Reviews
สินค้าถูกจัดเตรียม และ ส่งออกมาได้อย่างรวดเร็ว ของมาถึงเร็วมาก แพ็คเกจหนาแน่น ไม่ได้รับความเสียหายใดใด ตัวสินค้าสวยงาม ราคาเหมาะสม เล็กกระทัดรัด รูปทรงสวยงาม View detail
A little bit of installation. ? Will be
As others have mentioned in the review, the convex part to fit the lower cosmetic bolt×1 and the upper OEM bolt×2 do not fit if they are left as they are.
The lower inner side is fitted by grasping and compressing the inner side with your hand.
I am a little impatient because this area is not in the Instruction Manual.
I am not sure if it is only for the 2023 model, but there is a 5mm pin hole on the inner cowl side, which is flooded with slop water, so I filled it with Pate.
You can see it when you actually fit it, but it is a pin hole that does not bother you that much, so those who do not mind may not mind it.
I wanted the Fender angle to be a little more warped, but since it is a regulatory Limit, other Fender Eliminators may be the same.
View detail
For Chain exchange.
Used to replace Chain in 428 Size.
It is convenient to have multiple Adapters and to support various Chains. The texture is cheap, but the whole thing is rigid, and I think Large things like Pin are well made.
If you only need to replace it once, it is cheaper to ask a supply store, but doing it yourself is simply more surface white and satisfying. Durability is unknown.
View detail
Easy to use
I used to use another company's aluminum screws, but they were so soft that the hex on the head of the screw would come off when tightened.
It is getting worse as it spreads more and more.
This product is hard and tight.
If the head size were a little larger, I would have used four of them, but they were Exactly in the part I use.
Cost performance is good.
View detail
Fits: HONDA CRF150R, HONDA CRF250R, HONDA CRF450R, HONDA CRF250RX, HONDA CRF450RX, HONDA CRF250X, HONDA CRF450X, HONDA CRF450L, HONDA CRF450RL
When OEM is not readily available.
I bought this one in stock because the OEM was Timing which was not readily available.
There are naturally no problems with performance, quality, etc., and we have the peace of mind of being a DRC.
Thank you for treating OEM Equivalent Product as a niche for Motocrosser as well.
Racer has a low Oil capacity and will be replaced as soon as possible.
View detail
Conforms to ST1000 Regulation
I purchased the Tail Lamp to compete in the ST1000Class at the regional championships.
I purchased the DRC Tail Lamp because it meets the ST1000 Regulation.
Brightness is not a problem.
View detail
I'm happy with it
It is a Simple design, almost as good as OEM, but the functionality is Plusα. The Bellows part is back and forth from Quantity to Quantity.:Pair (for Left and Right) The Mirror can be moved to the position of your choice. Most importantly, when you fall over, the Mirror will probably run away from you, which will reduce damage to the Mirror. View detail
Fits: YAMAHA SEROW250, YAMAHA TRICKER, YAMAHA SEROW225WE, YAMAHA SEROW225WE, YAMAHA SEROW225W, YAMAHA XT250
Conscientious price and good quality
Compared to other manufacturers, the price is reasonable and the quality of the product is balanced. View detail
Delivery date undecided, huh?
I ordered in August 2023 and was told that delivery was scheduled for mid-February 2024, but I canceled the order at the end of February because it showed "delivery date undecided". It arrived the next day after I placed the order on Amazon.com. View detail
Commonly usable
It is not difficult to use and can be used normally.
In the usage situation, the handlebar is removed from the vehicle body, the handlebar is fixed in a vise, this product is installed, and the cut is performed.
It is not a tool I use often, but I think it is worth the price.
View detail
Easily change colors.
It is easy to change the color to match the car body color.
It is a general offfor vehicle shape, so changing the color does not affect the operability of the vehicle.
View detail
Fits: KAWASAKI D tracker, KAWASAKI D Tracker X, KAWASAKI KLX250, SUZUKI DR250R, KAWASAKI KLX250, SUZUKI DR250R
Texture.
Great texture.
I think it's hard to install if you don't have any experience.
View detail
Colorization while open ended
The grip was replaced with an open-ended grip in conjunction with the installation of a hand guard with a fixed grip end, so the color was matched to the vehicle body color. View detail
It's just a different look ….
I decided to replace the hose with a new one in conjunction with RadiatorCleaning and Coolant replacement for DRZ400sm k9, which had probably never been maintained. I wanted to change the appearance as much as possible, so I bought a DRC Hose set.
I really don't think it will be any different from the OEM in terms of performance, just a different look.
Since the coolant must be removed when replacing the coolant, it is best to change it together with the coolant replacement time.
Or when you plant a Water Temperature Sensor between hoses.
Well, we have to say goodbye to coolant anyway.
The handling is the same as the OEM, so there are no problems.
Band is also diverted from OEM as it is.
If I had to say, this Hose was more difficult to push into the back than the OEM Hose.
Maybe because it's brand new.
Reviewing the current situation since the replacement has been in place for 3-4 months, I do not see any deterioration of the hose itself, but the color has already faded.
It was bright red when purchased but has faded.
I think it's especially - because it's a Red color.
Recommended for those who want to change their look and feel.
View detail
Purchased for 23CRF250L
Purchased for CRF250L.
The minimum ground clearance is low because it is a non-S model, and also because it uses ACERBIS skid plates.
It does not fit under the Engine as it is.
I have to pull the vehicle up to get the STAND in, and when I lower it down, the STAND is stuck.
I would appreciate it if you could lower it a bit more.
I use STAND after putting the front and rear Tire on the Block because it is inconvenient.
If not for this, it would be a perfect score, but I originally had the same impresion for use on a CRF250L
I purchased at my own risk and have no problems.
View detail
It is inexpensive and easy to use.
[How is it used?
This tool was used during Tire replacement &Puncture repair work on a Dual Par Pass car.
We are currently using PROTOOLS' Air Valve Puller, but we used this product before that.
Many Dual PurPass vehicles that enjoy mountain play and forest roads use a Tube in the Tire, so these Items are very useful for getting the Valve of the Tube out of the Valve hole in the Rim.
Wire is thin, so please be careful when working with it, as the Wire clamps that hold it in place at the handles can easily come off or break if it is pulled with too much force.
Did you receive the item as per the Image?
Material:The aluminum and simple design of the handle makes it very easy to use, and its compact size makes it highly portable.:I always had it in my Set, it is just like the Image.
How did you like it?
Once you get the hang of it, you can easily pull out the Air Valve in no time at all.
Especially in winter, when tires become hard, I can't do without this product because it is so useful that I don't feel like doing it without it.
[Points to note]
After fixing to the Valve mouth because the Wire is thin Forced by brute force." Be careful when trying to pull it out, as it may come off from the clasp or Wire may almost break off, making it fragile.
If you search for DRCAir Valve Puller in the product introduction section of Webike, you will find a video at the bottom left of the introduction section that explains it in an easy-to-understand manner.
How did it compare to other products?
The wire part of this product was getting badly warped, so I bought a PROTOOLS Puller from Webike at a lower price at the time of replacement. I think I will go back to DRC's Puller when the Puller I am using now is no longer good. (Possible individual differences) 。
Other items that would be helpful
Point and hang of installation
With your free hand, press lightly on the backside of the valve of the tube toward the rim while guiding the tube.
The rest, as I mentioned above, you can watch the video.
Basics We're not in a hurry. We're going to do our job well and reliably." is the best shortcut.
[ITEMS TO BUY TOGETHER
Since this is used when replacing a tube-type tire, you will need to prepare a lever, BEETWax, and inflatoretc. for tire removal and tube replacement (you will also need a removal tool to get to that point).
[Opinions and requests to Manufacturer
It would be nice if you could use a stronger wire to ensure durability, but we would be grateful if you could just keep this product in the lineup.
View detail
I like the color.
This is my first ReturnRider in 8 years, but I have been using DRC mono for a long time, so this is a Repeat purchase.
I love the texture and color.
However, you should be careful not to widen the claws on the bottom side, otherwise the Wound will get into the edge of the License Plate.
(I actually inserted it without expanding it, and when I removed it, it had a Wound in it…)
Currently I am using only the color Washer and Bolt because they interfere with the Fender Eliminator Kit that I installed separately.
View detail
Challenge to recombine Rim
[How is it used?
The front wheel of the GasGas EC250 2023, which I always use for forest road touring, has become distorted and swung large, so I replaced it with a new rim. I used this Gyro Stand to build the Spoke.
How was your experience with it?
I worked with DirtFreak's You Tube as a reference while taking a swing.
It took us about two hours and we were able to correct the flare there.
The ride felt completely comfortable and I was able to replace the Rim without any problems.
The Off-road Wheels are easily distorted when used,
I felt it was important to correct Wheel distortions from time to time.
I am glad I bought the Gyro Stand and tried it myself.
View detail
Fits: HONDA CRF250L, HONDA CRF250L(S), HONDA CRF250RALLY, HONDA CRF250RALLY(S), HONDA CRF300L, HONDA CRF300L RALLY
Solid for the price.
The installation was easy with the Instruction Manual included.
Since there is no reflector, I installed DAYTONA's Slim reflector on top of it.
View detail
Exhaust pipe stepping stone injury prevention
I installed this Guard as a measure to prevent mud stains and scratches from stepping stones on the exhaust pipe. I am satisfied with the workability and cost performance of the Guard.
The only complaint is that the paint color of the Guard adheres to the exhaust pipe. Although I have some dissatisfaction with the product, I am satisfied that I have achieved my goal.
View detail