Reviews
Poly sports exterior
The hole to insert the washer is generally small. I went to Smooth for installation. View detail
No complaints at all so far.
I installed this bike for Enduro race on my KLX230R. it is fixed in two places at the handlebar and bar end to protect my hand and lever. the material is plastic and there is no gold frame, but I have used it for about 2 years and there is no trouble such as lever breakage. There is no trouble such as lever breakage after about 2 years of use. Since it is a universal product, it is necessary to cut some parts of the frame to make it fit perfectly, which is a little time-consuming. However, since the material is plastic, this is relatively easy to do. View detail
Fits: HUSQVARNA FE501, HUSQVARNA FE250, HUSQVARNA TE300, HUSQVARNA TE150, HUSQVARNA FE250-501, HUSQVARNA TE150-300
As Repair Lever
[How is it used?
I play mainly in Enduro race with HUSQVARNA TE250I.
I broke the brake lever during a practice run.
Pivot Lever Purchase
Was the one you received as per Image?
Installation can be easily done without removing the OEM lever.
The texture feels a little cheaper than previous Aluminum models, but it feels good to hold.
It was a little more Short lever style than OEM, which was surprisingly good for me.
I think this will alleviate the worry of it breaking in the event of a fall, but I haven't fallen over it yet, so I'm not sure how durable it is.
View detail
Fits: YAMAHA YZ, YAMAHA YZF, YAMAHA YZ125X, YAMAHA YZ250X, YAMAHA YZ250FX, YAMAHA YZ450FX
It has become a must-have item.
The shape is OEMLever itself.
The rigidity of the lever itself does not have any strange rattling, and it feels just like OEM.
Bottom line. Unbreakable." It works well enough as far as I'm concerned.
Bent Levers need to be put back by hand, but this should not be a problem for the average adult male.
There is probably nothing that surpasses this Lever in terms of cosmetics.
It's a good product
View detail
No longer a standard product
The Poly sports headlight has become a staple of Offfor Vehicle headlights.
Similar products are sold at low prices on Amazon, etc., but I have the impression that the difference in price is directly connected to the difference in quality.
In addition to the Rubber Mount that wraps around the Fork, two types of Brackets for adjusting the Headlight position are provided for installation.
View detail
Can not be installed
To install, a screw-in StraightSocket covered by a Rubber Bush is inserted into the hollow hole in the Pivot shaft of the Swing Arm, but the K7 uses a Quantity:Pair (for Left and Right) The Brake Side (Right) is too small and cannot be installed because the attached parts are of the same size. In addition, it is thought that a new car can be installed, but in the case of my car with rust and dirt adhering to it, the Shift Side (Left), which is thought to be the same size, could not be inserted either.
Although it can be machined and installed, it is recommended to use another Manufacturer's
View detail
WINnedProtector is easy to lose.
Total Material as well as KTMOEM:I like that it is Plastic.
We feel that it is moderately strong and supple and will be the first source of Damage in the event of a fall.
The problem is that the Black WINDProtector can be easily blown away by a Bush or tree branch and lost.
Grip end fixed Guard in general, but it is inconvenient that you can't hang a little Helmet on the Grip.
View detail
The quality is still different.
I have previously purchased a cheaper CHINA Exterior Kit. The quality and texture has improved a lot recently, but there are still some problems with the mold or the finish, such as bali, sagging, and deformed holes.
Poly sports' Exterior Kit has none of these problems. The exterior kit is beautifully finished in all areas and can be installed without any worries at all.
I am not too concerned about weather resistance for Motocrosser use, but what about TRAIL?
The Decal Kit will be applied immediately after installation, but it looks fine in terms of texture.
It is not surprising since the company also undertakes OEM for Manufacturer, but from User's point of view, the price is low and it is very helpful.
The fitment is listed as CRF450RX, but CRF250RX is also common, so it is used as is.
View detail
Genuine Polisport Frame Protectors for CRF250R
As this bike does take a lot of stick when it comes to being ridden in bad conditions, the purpose here was to get some better frame protectors. I have personally never used Polisport before but the customer specifically asked for this brand. Finding the part was not difficult at all as Polisport search function is really simple to use and you are greeted with what ever part is needed. The price from Webike was good value as they were actually in a sale at the time of ordering. I do have always some other parts to order so got them all shipped together via EMS. My order arrived very well packaged and 100% perfect condition. The frame porectors themselves a re a nifty piece of work. They are really a really tough rigid plastic composite but have a small amount of bend which makes this easy to fit. The finish and quality of these frame protectors is excellent as far as I can tell. They have a smoothed out matt look which works very well with the bike colour scheme. They attach pretty easily with the cable ties already included. If you wanted to go more permanent you could bond them on but cable ties for if you ever need to change them. Very pleased with this purchase and will look at Polisport in the future for other bikes if needed. Thanks Webike. View detail
Fits: YAMAHA YZ 450F, YAMAHA YZ 450FX, YAMAHA YZ 250F, YAMAHA YZ 250FX, YAMAHA WR 250F, YAMAHA WR 450F
Easy to install! Fit securely!
Installation is very easy, just tighten with Tie Wrap.
The brake hose is also cut to fit beautifully. The Swing Arm is now well protected and secure.
View detail
Fits: YAMAHA YZ 125, YAMAHA YZ 250, YAMAHA YZ 250F, YAMAHA YZ 450F
No, not very good.
As an overall evaluation, we have no problems with the material of the plastic part.
However, there are a number of critical problems with the other aspects of the program, and we do not recommend it as a general comment.
・Screw
This screw is included as a new item because it is co-tightened with the clamp section, etc. However, the accuracy of this screw is so poor that it cannot be hand-tightened with a ScrewSingle Body.
After machining the Screw with Dice, it finally went in.
In addition to the problem with Screw Mountain, there are other parts with surface scratches and other concerns.
In addition, although an Instruction Manual is included, it does not explain which screws to use and where to use them, and the quantity of screw holes is not included, even though they are to be used for the co-tightening described below.:The diagram is such that 2pcBolt will be included.
It is better to confirm the actual match only as a reference for assembly.
・Disc Side
Cannot be installed without modification
The discCard is installed after the Fork bottomGuard is installed, but even with the BottomGuardSingle Body, the screws cannot be inserted due to interference and distortion of the large screws. However, the distortion remains, so it is necessary to hold the whole body down while installing the screws.
The Glasses Wrenchetc. tool with a handle will not fit due to the shape of the area around the screw hole.
In the meantime, there is some relief in this regard, as a thin meaty Box can fit in it.
The bottom guard and disk guard are fastened by a single screw on the inside of the clamp, but the accuracy is not good, so serviceability is also a problem.
Opposite side
There were no accuracy issues here.
One point of improvement is the replacement of the hexagonal screw that holds the Fork Guard in place with the included screw, but this screw pops out quite a bit.
Originally, the head height was designed to be lower than that of the plastic Guard to prevent damage to the head of the Screw in the event of a fall, etc. However, since the attached Screw is a bolt with a normal head, it sticks out about 8mm.
This condition will quickly ruin the Screw as it is the part that is most likely to be bumped during a fall.
I thought it would be better to find some good Screw and replace it.
View detail
Used in conjunction with Under Guard
Right Side is the lower half of the ClutchCase Magnesium cover
Cover each of the following.
It prevents damage when falling on stones or hitting trees, and also protects against scratches and stains caused by Boots rubbing.
The generator side is perfectly protected by this alone, but the water pump on the clutch side does not have a cover, so it is possible to separate the water pump by using the Under Guard side to follow the water pump.
The back side has silicon rubber along the protective section.
The inside of the pack is unusually clean when removed after driving, as it serves as a shock absorber as well as for packing. However, after riding with Muddy, it is recommended to remove and wash them because of the mud that gets into them.
The attached screw is long enough to hold the device in place in three places, and it has never leaked even with oil in it, so it can be attached and removed by course.
Quantity:Pair (for Left and Right) Remember to tighten the cover tightly in advance, as 1 pc of each will be hidden under the cover.
View detail
Looks Yoshi for Defensive Up:??
It was guaranteed to fit up to 21MODEL, but I was able to pop it on my MY23 YZ250X.
The work is completed in a minute or two.
In addition to its defensive capabilities, the Engine waist looks tighter.
View detail
It looks good, but the light leaks.
I have a TT250R, but the light is too dark (like a moped) and the face is a little too much, so I changed to this one which is cheaper and has a headlight.
Installation is as simple as using an Elastic band and tying it to the front fork, but of course the coupler on the Headlight will not fit, so it may be difficult for someone who can tinker a bit.
Headlight Bulb is one of the objectives as it also fits H4 Light Quantity Up】 【Light Quantity Up I personally think that Parenthesis is good with a Small face and the NORMAL look is gone.
Minus point is light leakage.
As you can see in the picture, the headlight leaks quite a bit around the meter. Also, there is no Instruction Manual, so it may take some time for motorcycle beginners to understand.
Well, it is cheap, so overall I am Large satisfied!
View detail
pimping
UFOTwin Headlight Halogen discontinued, Light is too dark, changed to XRMOTARD playback.
LED with Sphere God of thunder Gu2 to match.
Installation is done with a simple push-on installation.
The adjustment range is narrow and it is difficult to adjust the optical axis.
It looks small and parenthesis is nice. I am a little concerned that the OEMMeter is not hidden.
It is much brighter than Twin Headlight, but Off-road motorcycle lights are still dark.
View detail
Fits: YAMAHA YZ 450F, YAMAHA YZ 450FX, YAMAHA YZ 250F, YAMAHA YZ 250FX, YAMAHA WR 250F, YAMAHA WR 450F
I think it's good.
[How is it used?
Forest road Gare
Was the one you received as per Image?
as it is (i.e. now)
Was the installation difficult?
Easy
How was your experience with it?
It serves its purpose.
[Included Parts:were they on?
It comes with Sponge as a buffer.
[Was there anything that disappointed you?
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Bolt holes match, so it is possible to mount the bolt.
[How is it used?
Last 2CycleMotorcycle of my life!" KDX220SR was purchased used with great enthusiasm.
Since the vehicle is over 20 years old, it is inevitable that the exterior will become crusty due to UV rays and age-related deterioration.
Since the design of the Front Fender has almost no connection with other refurbished panels, we dared to purchase and install a product with the same design as the current Kawasaki off-road model, regardless of the design at the time of its release.
It may not be suitable for those who want to finish with OEM parts of the time, but I personally feel no discomfort, and I think it was a good purchase because it is difficult to be distorted by wind pressure while driving and the handlebar is not taken off while driving on the highway.
Did you receive the item as per the Image?
The product was exactly as shown in the Image because I had to confirm that it was the same design as the vehicle currently being discussed by Kawasaki.
Was it difficult to install?
It is an extremely simple job, simply remove the four Front Fender mounting bolts that were originally installed, remove the wires, and then install them in the reverse order.
How did you like it?
There is a gap of more than 20 years between the exterior design of the Front Fender and Others installed this time, but I personally do not feel much discrepancy.
Is this because it is not installed consecutively with other exterior parts as mentioned above?
I don't know if it's because I'm replacing the light cowl with a product from another Design company. (OEMLight is too dark and has been replaced with a light cowl that can be fitted with H4Type Valve). 。
Ultimately, if the owner likes it. (This is based on the assumption that Large is not a nuisance to those around you.) I don't see any problem with what a third party can say.
It is a world of complete self-satisfaction, but I am happy just looking at my car in its Beauty exterior.
Was "Included Parts:" attached?
Front FenderBody only, no Included Parts:or Instruction Manual.
Were there any disappointments?
Nothing personal, I am Large satisfied because I was able to purchase a product of the same design for a little less than OEM Product.
Other items that would be helpful
Point and hang of installation
In a sense, this product is also like OEM parts, so there is no hang or anything, but it is definitely better to temporarily assemble the product and adjust the overall adjustment before fixing it in place, just to be sure.
[Availability and clarity of the Instruction Manual
No Instruction Manual, no, but as noted above. All you have to do is remove the same type of parts that were originally installed and install them in the same way." So I don't think Instruction Manual is necessary.
[Notes]
Nothing in particular, if it is an Other Brand Product. Screw holes won't fit." However, this product has no Bolt hole gap and can be assembled without any problem.
The bolt holes are slightly wider to allow some forward/backward movement for balance adjustment. "Temporary group." I would recommend that this fixation be made from
[ITEMS TO BUY TOGETHER
Since the motorcycles themselves are more than 20 years old, sales of OEM parts as well as other brand products are about to end.
It may be a good idea to Stock items that can be replaced while they can be purchased and parts that may need to be replaced in the future.
[Opinions and requests to Manufacturer
We look forward to a long and continued Lineup.
View detail
Can be mounted on 20-22MODEL (Decal is Gap)
The hole positions are the same for the 20-22MODEL, so installation is no problem.
Since the plastic molding is individual, apply a little force while attaching the bolt so that it is straight.
The shape of the shroud is slightly different, so if you use OEMDecal or 20’-compliant Decal, I think you have to cut it a little to get a clean paste.
I took a picture so you can refer to it.
I think most people will smash it and replace it, so I don't think many people care about Decal breaks, etc., but I hope this helps.
View detail
Wow that's cool
I installed it on my CRF250L. The color is almost the same and I am very happy with the fit.
Installation was also easy since it can be simply attached.
View detail
CRF250L with a pontoon
I bought this product because I wanted to put together the cowl and other parts of my CRF250L in White. I had bought the same product in Red before, so I knew I could put it on my CRF250L, so I chose this over the more expensive OEM.
Since it was originally designed for CRF150L, there is a gap under the headlight, but I think it looks good.
View detail