Reviews
in line with the price
I am thankful that it is much cheaper than OEM Product.
It is also nice to know that the body can be any color since it is Carbon Style.
With JC61, if I wanted to use the collar that came with the OEM, I had to use a drill to widen the hole.
If you use Bolt without collar, it may not be necessary to modify it, but I am afraid that it may crack.
For people who prioritize cost performance anyway.
View detail
Fits: HONDA DAX, HONDA CHALY 50, HONDA MONKEY, HONDA GORILLA, Others , HONDA DAX70, HONDA CHALY 70, HONDA ST90 (ST90)
Commonly usable
Blinker relay of 6VMONKEY was broken, so I replaced it with this one. There is no particular problem, but the unique clinking sound of the blinker is gone, which is Minus. View detail
Fits: HONDA dachshund, HONDA Shirley.
OEM Equivalent Product
The front hub bearings were sticking and the shaft axle was worn, so we replaced them with new bearings. The paint was very good and the bearings were already greased up, so it was just a matter of assembly. View detail
Parenthesis good!
I installed it and I am satisfied with its appearance and Parenthesis.
However, the Change Pedal and the sub-frame interfere with each other because the engine is set to 125cc, and it seems that some ingenuity is required for installation.
View detail
Fits: HONDA MONKEY, HONDA GORILLA, HONDA CHALY
CROSS CUB (JA45)
Used for CROSS CUB (JA45)
The one from a certain Manufacturer is too expensive, so I chose this one.
It doesn't feel Aluminum-ish, but the texture is usually good.
It is also easier to turn when adjusting, increasing practicality.
View detail
Probably shoddy
I was able to use it, but the bearing assembly of the rotating part is not right.
The rotation at the time of jack-up is terribly heavy because of it.
As delivered, the grease of the moving parts was dirty and covered with iron powder and dust,
I took it all apart and Greased it up again before using it.
View detail
Fits: HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Necessary thing
Защита маятник нужная вещь. По просьбе друга купил ему . Она прекрасно подошла на его Honda Monkey. Теперь он доволен и радуется использованием. Отличная недорогая вещь. Рекомендую всем.
The pendulum protection is a necessary thing. At the request of a friend , I bought it for him . It fit perfectly on his Honda Monkey. Now he is happy and enjoys using it. A great inexpensive thing. I recommend it to everyone.
----------------------------------------------------------
Protecting the pendulum is the right thing. At the request of a friend, I bought him. She perfectly approached his Honda Monkey. Now he is satisfied and rejoices in use. A great inexpensive thing. I recommend to all.
The PENDULUM Protection is A Necessary Thing. At the Request of a Friend, I Bouught it for Him. It Fit Perfectly on His Honda Monkey. Now he is happy and enjoys using it. A Great Inexpensive Thing. I Recomment it to EVERYONE.
Powered by Google Translator
View detail
I wonder if I need it to replace the carburetor on the CUB.
Since the replacement of the carburetor in the CUB forced us to replace the cook with an OEM fuel cock carburetor, we had a little choice and thought about it.
(1) 2 system Cook replacement
(2) No Cook with Tank set to Custom.
(3) No Cook with Tank as one line with After stuff.
(4) On/OffCook installation with one Tank system.
So, for now, we decided to just use Cook, which is cheap and doesn't cost a lot of money up front.
The mounting position was extended with Bracket and temporarily attached. It was usable as usual. Not bad for the price.
I just put it on, so I don't know how durable it is. Therefore, I gave it 1 star minus.
View detail
Required for disassembly work
It would be nice to have when doing overhaul.
I have searched and found that many people reuse the Crankcase gasket, but I think it is better to smooth the Crankcase gasket with oil stone and replace the gasket to prevent oil leakage.
I studied the initial overhaul with New Engine.
View detail
Fits: HONDA CUB, HONDA CUB, HONDA CUB, HONDA CUB
Required for Engine conversion
I purchased the Crankcase because I needed it after the engine was converted to a Large type.
I would have preferred a foldablefootpeg if I could have, but I had no choice.
Brake pedal is also a Quantity:Set, and is required in the Quantity:Set sales are Reasonable and appreciated.
Perhaps Pedal plating is more prone to rust than domestic plating, so maintenance will be more frequent.
View detail
Fits: HONDA shirley, HONDA dachshund
I put it on CHALY.
We have a product BALI, so we have to prep it.
Painted. I think it is good for the price.
View detail
Fits: HONDA dachshund, HONDA Shirley 50., HONDA Dax 70, HONDA Shirley 70
CHALY That!
CHALY I bought it to make a thicker footprint of the I am satisfied with the cheap price. View detail
Fits: HONDA MONKEY/GORILLA, DAX, CHALY, CUBetc. vehicles equipped with Horizontal TypeEngine, HONDA MONKEY, HONDA GORILLA, HONDA CHALY, HONDA CUB
This is faster and quicker than a poorly designed Engine.
I bought this once because the Engine I put together myself was sluggish no matter what I did.
I was wary of the Chinese Engine or ……, but it worked on the PON without any problems.
I don't know about durability etc. yet, but I didn't have any difficulties except for the wiring process on the car body side.
CUBOEM's SeesawShift Pedal can also be used normally.
However, as mentioned earlier, if the supplied Harness is not used, it is necessary to modify the generator/StarterWiring on the car body side to Bullet Terminal.
Especially with Cell motor Harness, you should buy a Bullet Terminal that is compatible with thicker Cable because you need to process the thicker Wiring for Starter on the Grounding Wire.
View detail
More than Bore up.
Swapped from SUPER CUB 50 OEMEngine
With Engine itself pon
The carburetor came with a 16π? The carburetor came with a 16&pi carburetor, but I used a pc20 funnel and a YOSHIMURA intake manifold. The rest is KITACO clutch wire and clutch lever.
FSprocket exchanged R for 15, or was it 38?
I'm not sure about Included Parts:as you don't mention it specifically,
I tried to use the Indicator and found that there are two in the box, one for the carburetor side and the other for what? I tried to use the Indicator and found two in the box, one for the carburetor side and one for what? Well, I don't need it because CUBOEM13π is obviously not enough for 86cc lol.
The original engine oil was replaced with G2Oil after warming up and breaking in salad oil.
I don't know about the attached carburetor, but after breaking in, full throttle, well, thanks to the pc20, the CUB is no longer a CUB. 60kmMeter is swept away in about 5 seconds.
Another AA01 centrifugal 3 speed 88ccHigh Camshaft18πcarburetorOthersSprocket uses the same size, well, Gold amount is more expensive to bore up, so it is still recommended for those who want Manual clutch.
Installation can be easily done by one person.
The difficult part would be to modify the terminals to match the Engine side when using OEMHarness.
I think it would be more of a hassle to replace even the Harness.
As you may have read in other sites or on our side, the first time GEAR enters the market, it is very reluctant to do so.
Neutral goes in for me, but I often have trouble returning to 1st gear from 2nd gear.
The wiring diagram in the Instruction Manual was Harnessfor MONKEY, but the color was the same in CUB.
I don't know how durable it is since it is currently just loaded, but I hope it was a hit.
View detail
Fits: Others Universal
Less than six months later, this is what you get.
I bought it because there was room in the mounting area.
I bought it thinking it was made of Gold because it was more expensive than other companies' products, but it was inferior plastic.
Thanks to your help, I was just running, but the bolt of the Cover cracked and shattered from the receiving part of the bolt.
The structure is also bad, so if this part cracks, the Filter will not be routed through at all!
I got fed up with all the shoddy Powerfuls with Covers from all the Manufacturers, so I eventually went back to OEM.
View detail
Fits: HONDA MONKEY, HONDA CHALY 50, HONDA DAX70, HONDA DAX, HONDA GORILLA, Others , Others 4-pole terminal RegulatorSpec. It can be widely used for vehicles.
Voltage increased slightly when running.
I bought this Regulator to review the ignition system because the MONKEY was malfunctioning. It was not the direct cause of the problem, but the original one was so old that it seemed to be worn out. After replacing it with this product, the voltage when driving went up a little. It is a little bit larger than the OEM product, but I had no problem installing it. View detail
Fits: HONDA DAX, HONDA CHALY
Tanaka Dax fender
Fitment is great and paint finish is beautiful. Fitted on a USA spec 1970 Honda CT70 that I am converting to Japanese spec. View detail
Fits: HONDA little cub, HONDA Super Cub 50, HONDA Super Cub STD-92 (12V model), HONDA Super Cub STD-92 (12V model)
Don't expect quality.
I had a headlight unit from another company attached to my LITTLE CUB, but after more than 10 years of use, the plating was peeling, so I replaced it.
The installation itself was not a problem, but the Socket does not seem to be durable.
I installed it at the end of September 2023 and from the beginning of December 2023 the Headlight started flickering occasionally and a few days later the Headlight disappeared while driving and became completely unusable.
I suspected that the Valve was out of ballast and tried to remove it, but for some reason it would not come off. When I pulled it out by forcibly turning it with pliers, I found that the Socket had melted. The melted valve had lost contact with the valve, and the resin was further burnt.
Since the price is reasonable, I think it would be better to use OEM products like Large for Socket and Valve, with Socket and Valve as extras.
View detail
Fits: HONDA CUB, HONDA MONKEY, HONDA dachshund, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA dachshund, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla)
Easy to change carb position
Casting seems very strong, however the casting port hole for the engine side is not perfect. I'll need to use a Dremel to tidy up the port as can be seen in the photo. Otherwise I feel it will not produce as good as power as it could. Installation is very easy on monkey due to being able to position the carb however you like. Product was priced well just a shame about the casting hole. Webike is always very quick with shipping A+ View detail
Don't buy it.
I bought a DID 530VX3 to Crimp an existing Chain to replace the Chain, but the Crimp pin broke off and I could not Crimp it.
I managed to cut the chain by using Leutor to drop the crimp at the end of the chain and then cut it, but it seemed to break.
It was not of the least use and dumped the Gold down the drain.
I bought a similar Tool from Amazon for about 3,000 yen because the parts seemed to be usable, and it broke the same way, so I assume the contents are the same.
I ended up buying DID's Kashimaru-kun and did the Crimp, which is an OEM-specified product, and was able to do the Crimp easily and without any danger at all.
View detail