Reviews
Soak before fitting
I soaked them in warm water prior to fitting, as per the advice of other reviewers.. No issues getting them on the levers, it did take a few minutes for each side though. They are sufficiently firmly in place that they don't move around at all. Although I expect they may shift a bit if they get wet. View detail
SP Mukawa Lever grip
[How is it used?
Used for scooter levers
Was the one you received as per Image?
As per Image
How was your experience with it?
Good feeling when gripping.
[Points to note]
May not fit depending on Lever size
How did it compare to other products?
There is no comparable product.
View detail
Fits: HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA Cross Cub 50, HONDA cross-cub 110
If you try to fit it in when it's cold, it rips.
When I tried to fit it, it ripped and was destroyed before I could use it. View detail
Fits: HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA Cross Cub 50, HONDA cross-cub 110
Lever does not get cold
Installation was done by wetting the inside of Sponge and Lever with water.
Forcibly attaching it will result in tearing or shredding of the sponge.
*When installing, it was written in red letters not to use organic solvents, oils, or greases because they cause slippage or deterioration.
The effect is outstanding. Lever gets quite cold in the cold winter, so there is a big difference between having it and not having it.
View detail
Fits: HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA Cross Cub 50, HONDA cross-cub 110
One pointAccent！
I bought this as a One pointAccent on my Brake lever. I like the manufacturer's logo. (^O^) View detail
SP TAKEGAWA Lever Grip
About quality and texture It's a common product for sponges About the feeling of use It feels soft Products to buy together None. Difficulty of installation It's hard. I'm wearing a takegawa quick lever, but the end is round, so it's hard to put it in from there Cost performance and comparison with other products The price is good, but it feels like a one-time product About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing I was going to use the reinforced clutch because my hands felt tired, but if I installed it now, I thought it would not be usable at all during the riding season, so I postponed the installation View detail
Is good
Lever becomes easier to grip and prevents slipping.
The cushioning is good, so the hand feels better when gripping it, and the hand does not get tired.
It is easy to install, but care must be taken not to tear it.
View detail
As a measure against cold, it is better than nothing.
I installed it on the Scooter that I use for shopping, etc.
It is installed on Initial ModelBirdCity125 and OEMLever.
I bought this to see if it would help with the coldness of the Lever, which is transmitted even when wearing winter Gloves.
When I actually use it, it's better than nothing, and cold things are cold, but I feel that the speed at which the heat is taken away from my fingertips has slowed down.
It is uncomfortable at first because Lever becomes thicker when you put it on, but it does not interfere with Lever operation because there is an unevenness that matches your finger.
When I put it on, I tried to put it on Lever without thinking anything and I went as far as wrapping the ball of LeBar End, but it didn't proceed from there. I remembered that I used detergent in the impression of other people and I put 1 or 2 drops of kitchen dishwashing detergent in the hole. I put a drop or two of kitchen dishwashing detergent in the hole, and it went in easily.
It moves right after I put it on, but after a few days, it doesn't move anymore.
View detail
Fits: HONDA CROSSCUB110, HONDA CROSS CUB50, HONDA Cross Cub 50, HONDA cross-cub 110
One point on the brake lever
Installed as a dress-up for the CROSS CUB Brake lever. It is expected to relieve the coldness of the lever in winter.
I was able to fit it without ripping it by wetting it with water thoroughly when I put it on.
View detail
Be careful not to pull too much.
It is easy to install but you need to be careful not to pull too much to avoid tearing. View detail
It ripped when it was first installed!
The Clutch Side was a breeze to install! But Brake Side ripped it up in one shot! Lever is made by the same brembo. The torn one I touched, the rubber is hard and won't stretch! Did you mix the new one with the sifted one, SP Takekawa-san, that's terrible! I trusted you!
Related Videos
[MONKEY125] For some reason I installed the well-received Parts OUTEXSteering stem stabilizer!
https://www.youtube.com/watch?v=4IqK231SbMQ&t=2s
View detail
Anti-slip, improved grip!
It is installed and used on the OEM Lever It helps to prevent slippage, makes the grip more comfortable, and reduces the vibration transmitted from the Lever When using it on rainy days, use a dry Towel to drain the water out of it If they are still wet, they will shift in position View detail
Grip
This is the second time buying this grip. Good feel on the lever. Nice material and the feel on the grip on brake or clutch improve. More response on brake tap on fingers. View detail
Lever Grip 06-08-3029
SP TAKEGAWA(Special Parts Lever Grip 06-08-3029)last round, black order Come to try and feel that the foam material is good quality, soft and durable, but the screen has some peeling according to usage. At a satisfactory level so decided to order it again in blue. SP TAKEGAWA (Special Parts Lever Grip 06-08-3029) Last Round Black Order Let's try to feel that the foam material is good quality, soft and quite resistant, but the screen is somewhat peeling by the use. At a satisfactory level, I decided to order again in blue. (translated by Google Translator) View detail
Get cold
It's hard to get in, so when I paint Bead wax in, I entered it very easily.
However, after putting in, slipping too much will wrap around it unless you wipe it off.
View detail
I regret to rip it - - -
I put it on the APE 50, expecting it to be easier to grasp.
As Instruction Manual Wet with water Challenge. OEM's Brake lever side was able to be installed somehow, but the Clutch lever of the Other Company Product was cracked as the bulge of Les Bar End was somewhat larger than the OEM, it pushed in and forcefully.
Making is solid (Strong) The installation is Large strange as you are doing. The Manufacturer's Instruction Manual that I repurchased was written to use a small amount of neutral detergent. You may have installed it with detergent.
The feel I grasp is somewhat stiff (I like preference for a bit more). It is stylish that Mukawa's Logo is included. I was not able to install it properly in my case because it was expensive, so I made it a lower evaluation.
View detail