Reviews
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-03 (2015-), YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
I installed it on a 2023 R25 ….
The Shift side is fine, but the Brake Side is a problem.
As you say, it is impossible with the included Plate.
I really wanted to set it at 50mm up and 50mm back, but the brake hose interfered with it and it was too tight, so I set it at 45mm up and 40mm back.
The plate was substituted with a KITACO Universal Bracket that was left over in Garage and a nice color that happened to be available.
After installation, the knee grips feel better and easier to use.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-03 (2015-), YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
It was great.
You can feel like a Racer just by installing the Plate. View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-03 (2015-), YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
The instruction manual is confusing.
Installation is easy.
However, the instruction manual is difficult to understand.
Watch the video on YouTube to see the Point during installation.
You can install it with Included Parts:only.
Of course, you can't install it without modifying the Cable or other handling.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-03 (2015-), YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
RearBrake master cylinder
RearBrake master cylinder is difficult to install with just the bracket that comes with it. View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-03 (2015-), YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
Inexpensive and Sporty
The NORMAL footpeg is almost directly below the seated position. It is a common part with MT-25/03, so it can't be helped, but.... In addition to the appearance, I, who am 174cm tall, had a problem that it was too narrow and hard for me to operate.
In fact, Rear Sets, which replace the entire unit, would probably be better, but they are too expensive, so in my case, these are sufficient.
40Back/45Up、40Back/35Up、50Back/50Up、50Back/40Up (mm) I have 50Back/40Up for now.
It didn't even make my legs feel tight. This is it!" It's like
The drawback was that the included Brake fluidTank Bracket was too short and caused the hose to bend unnaturally, so I later made my own Bracket with a commercial Bracket.
Also, it may be a matter of familiarity, but the Side Stand is now slightly harder to get out.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-03 (2015-), YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
hopeless case
After all, only the bottom hole is usable.
Brake hose also needs to be devised.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-25, YAMAHA MT-03 (2015-), YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
To prevent contact
To begin with, OVER RACING's TTFORMULA 750S (for yzf-r25) I was wondering if I should use Rear Sets or Step Up Bracket, and then I bought this Step Up Bracket. I was able to install it in a position where the exhaust system does not come in contact with the footpeg and the footpeg does not rattle when driving on the circuit. I personally recommend to use the OEM set up first, and then gradually change the settings. In that sense, Step Up Bracket is just right parts. View detail