Reviews
Fits: YAMAHA SR400, YAMAHA SR400, YAMAHA SR400 19, YAMAHA SR400 19
Perfect Kit!
This kit made replacing my OEM handlebar very easy. All parts were good quality, and the new cables and brake hose were cut to the perfect length. I highly recommend this kit for those wanting a straight-forward option to giving your bike the cafe-racer look. This was installed on my 2015 Yamaha SR400. View detail
Fits: YAMAHA SR400, YAMAHA SR400, YAMAHA SR400 19, YAMAHA SR400 19
To CafeSpec.
The quality is good and the product is from a reliable Manufacturer.
Position changes considerably, and the posture becomes more forward leaning.
Compared to the separate handle of yzf-r25, the position is lower, the Sauce angle is also there, and I feel that the Handlebar under the Top Bridge makes such a difference.
Sauce angle doesn't seem to be too much, but if you ride long enough, your wrist will hurt.
I think it is a little difficult to ride, but I think that is one of the best parts of Motorcycle.
View detail
Fits: YAMAHA SR400, YAMAHA SR400, YAMAHA SR400 19, YAMAHA SR400 19
It's easy and helpful. But that's all.
I installed it on my Type 5 SR400FIMODEL.
I want to use Separate handle for now, but I don't know.
In such a case, the quantity that Recommendation DAYTONA is putting out:The Set.
If you buy this Separate Handlebars Set, external Headlight Bracket, and Brake fluid, you can make it to Separate handle.
The solid rigidity, the convenience of adjusting the Sauce angle, and the Other Brand Product "I welded Clamp to the Iron Pipe. It's very good that it doesn't feel cheap like
However, depending on the installation position and the compatibility with other brand products, it may be very difficult to install the wires.:The length is decided as a Set product, and it becomes revenge. In my case, Wire of Decompression interfered considerably, and it was difficult.
Also, personally, I would have preferred a Handlebar with a Grip end attached.
View detail
Fits: YAMAHA SR400, YAMAHA SR400, YAMAHA SR400 19, YAMAHA SR400 19
Cafe racer has a Separate handle
I had it on my SR400.
I was using Normal baseCafeSpec.
good point
1 Cable, Handlebar Stopper, etc. are available. Thanks for your help.
2 Handlebar hanging angle is not too loose or too tight, just right.
3 At any rate, it will be cool. You can be like a British Cafe racer.
4 Since it's DAYTONA, you can also buy repair parts.
A bad point
1 Position. because the footpeg of the Position of NORMAL is closer to the front, it is good to replace it with Rear Sets. By the way, OEM Rear Sets (OEM footpegs from '85 to '95) are recommended because external Rear Sets are expensive.
2 Decompression is not available.
You need to be a little creative, but it will definitely improve your parenthesis.
View detail
Fits: YAMAHA SR400, YAMAHA SR400, YAMAHA SR400 19, YAMAHA SR400 19
Handlebar is good, but ...
Handlebar itself is not bad. It is very easy to get on because there is not so much hanging angle.
However, the kind of Wire is somewhat subtle.
I am on the 2007 ceremony, but since 2001 Quantity : For Set, Wire is -80 mm from OEM (By the way it is said that the previous one is -100 mm. ).
Clutch Wire may be due to my own handling, but it is quite long. It may be better to shorten another 20 mm. Therefore, we extend Screw of play adjustment to the limit Limit. Still LimitClutch is about to expire.
The biggest problem is that Brake hose is hard. Anyway it's hard. It is hard enough to not handle it at all. I gave up and used OEM's Hose.
Accelerator Wire can be used without problems.
Decompression wire attached posh's decompression lever, so it is unused.
This Quantity : It may be better to buy OmegaHandlebar with Single Item than to buy a set and arrange different types of wire.
View detail