Reviews
good value for money
Material of Type using K-FACTORY's OEM License Lamp:I purchased this Eliminator to replace my Stainless Steel Fender Eliminator, which has a Stainless Steel base plate, black chrome plated and clear coated finish. I am satisfied with it because it is less expensive than other manufacturer's Fender Eliminator. In my case, I replaced the blinker with a POSH one, so it took time to adjust the angle and position of the blinker.
Of course, the accuracy was also fine. However, it would have been better if the bolts on the base plate were black instead of stainless steel.
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
Refreshing with Slim design
I bought it because I wanted it to look Refreshing and Sexy from the back.
I am quite satisfied with the design, which is slimmer than other products.
I think most of the other companies' products are a little more blobby.
With this product, it seems as if it is integrated with Cowl.
The Instruction Manual was easy to understand and the DIY installation was a breeze.
View detail
High quality
The fitting was good, and the HarnessAdapter setting was smooth. The fitting was good and the HarnessAdapter was set up smoothly. View detail
Easy to install and good look
This eliminator kit is within a hour installed and contains all parts nieder. I had to readjust the angle of the Lizenzen plate due to german law. That is no problem with this product. Recommended. View detail
It's a great costumer
The ZX-14R's ungainly rear area will be refreshed. When installing, pay attention to the wiring and other things. I mistakenly cut off the ETC wiring. ('; Ω; `) 。
It is less expensive than otherManufacturers, but it requires a separate Reflector, so is it still the same in the end?
View detail
good
I am very satisfied with the HURRICANE soilless removal kit. It is easy to install and rich in accessories. It allows the removal of the cargo rack to make the rear line look better. The workmanship is good. Non-destructive installation. The license plate light is very bright and cost-effective. View detail
Cheapest in gsx-r1000r fit
The License Plate Light and the Connector for power connection are included for easy installation.
The shape is simple and good.
View detail
Happy to be Refreshing
I'm happy with the Refreshing look around the Rear.
I was troubled with the Active product, but I decided to go for the Made by HURRICANE product, because I don't need to change the key cover of the Seat lock when I use the NORMAL bracket.
I'm a little bit worried that the LED License Plate Light is attached with Double-sided Tape &with Reflector, and the Made by HURRICANELicense Plate Bracket is Quantity.:I think Set would be a great product.
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
A satisfying dish
The InstallationInstruction Manual is a little hard to read, but it didn't interfere with the installation.
It looks great and I'm very happy with the Large.
View detail
Perfectly made, I'm happy!
I installed it on my 2010 CB1300SF. it took me a long time to remove the OEM fender and the tail cowl was cracked, but I managed to remove it. The installation itself was easy and no problem, but if I had to say, I would have appreciated if the instruction manual was a little clearer. View detail
CostValue High!
[How is it used? 2 weeks after installation
Was the one you received as per Image? It is almost as Image.
Was the installation difficult? I think it's relatively easy to install even if you don't have much skill.
How was your experience with it? I really like the angle of the Number.
[Included Parts:were they on? Not particularly.
[Was there anything that disappointed you? Not particularly.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer It was difficult to pull out the coupler of normal fender from between the frames, so I cut it off. When you install it, you can pass it through without any problem because there is Bullet Type Terminal in the middle.
View detail
Fits: HONDA CBR250R (2011-), HONDA CBR125R, HONDA CB250F
Number one for compactness and stylishness!
I bought this to install on my '14 CBR250R late model.
The mounting holes are open for both the first and second semester, so it can be used with either.
When I purchased this kit, I compared it to the Fender Eliminator Kit TYPE 2 made by False Design.
Because it is the commodity of the appearance which is very compact and stylish with the License Plate Light which is not conspicuous in the Small Type of LED, both were comparing and examining, but when it installs NumberSIDEBlinkerCompact made by Active at the same time However, I hesitated at the price of double of Made by HURRICANE, so I decided to process and install here.
[Contents] The Fender Eliminator Body is divided into 3 parts, LED License Plate Lamp, a set of mounting screws & Rubber molds at the rear end, tape to cover the unused holes, and instruction manual.
The product is made of 3mm thick aluminum material with good fitting and finish on each part.
Anodized is also applied evenly and beautifully.
The manual does not describe the disassembly around the Tail as carefully as the service manual, but you can get the flow, so if you don't want me to teach you how to do it, it's not a problem.
The installation of the Fender EliminatorBody is illustrated and very easy to understand.
I didn't need the OEM Blinker mounting base, so I cut out the Number mounting parts from the same thickness aluminum plate and made them myself as shown in the attached image.
Quantity:I could cut off the Blinker mounting base of the Set product, but I don't want to be able to put it back when I need it…
One of the reasons we chose this product was that it was structurally easy to manufacture this part.
Easy to install. The LED License Plate Lamp Connector is also Bullet Type Terminal so you don't have to worry about wiring.
However, since there is no clear positioning for attaching License Plate Light, please be careful.
Please refer to the attached image of the figure installed together with the Number baseReflectorW122&Active NumberSIDEBlinker made by the company.
Personally, I think that there is no other Fender Eliminator Kit for MC41 that is so refreshing.
The construction is robust and there is no concern about damage from vibration.
The attached LED License Plate Lamp is also very bright in both brightness and irradiation range.
I think that the person who is concerned about the mud splash does not make Fender Eliminator in the first place, but I think that it is still better in terms of the position and angle of Number.
By the way, when the kit is installed as is, the Number installation angle is about 40-Degrees. (Depends on the suspension and individual …)
But it's not without its concerns.
First of all, because it is exchange for stylishness, it is unavoidable, but the wiring of the tail circumference which was settled in OEMFender is translated to move in Fender Eliminator, but it is very small in space.
I'm adding terminals and Wiring myself. (Please refer to the diary) And even more so, I can't afford the space.
So, be careful not to squeeze or pinch the Wiring or Connector during Tail cowl installation.
As for flooding in the Tail cowl, it looks like it will be more than OEM…
If you are thinking of using a short LED Blinker etc. attached to the Blinker mounting base because there is a mounting base behind the Number, it may be hidden by the Number and become difficult to see, so it is necessary to check.
Also, the attached screw is too long even if the individual difference is considered.
The nut with looseness prevention is put in the body side of all four installation screws, but it is strange to turn to the tightening position.
It's not a problem for installation, but it's awkward to have four screws sticking out unnaturally in the tail cowl, so I'm planning to replace them with screws of appropriate length.
If you like this design and you can understand Demerit, I think you can buy it without a doubt.
View detail
It's a good, solidly built product
It was inexpensive, well-built, and easy to install
The other Fender Eliminator has a gap between it and the stop lamp and I don't like it very much is not, and this product is great because it doesn't have that, and it doesn't feel different!
I'm glad I refreshed the rear area and purchased it
View detail
It's a good costumer and looks great
When I bought the GSX-S1000, it was my first Custom for the HURRICANE I threw in the Fender Eliminator Kit
The installation system is perfectly fine, and the Installation Instruction Manual is included I think it can be installed easily in about 30 minutes if you do it while watching it In addition, the cheap price and the wiring process of the position lamp is very easy to install I liked the fact that it was unnecessary
The only complaint I have is that the Reflector is a Quantity:The point is that it is not a set and must be purchased separately
Recommendations for those who don't care about the brand, and who care about the costumes I think it's a product
View detail
○
I installed it in MODEL of 2020/2/20 release, but it can be installed and used without a problem
Naturally, the bounce is great
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
Cool
Reflector is the license plate base of CB400SF (sold separately) I purchased a The assembly, wiring, etc., can be installed comparatively plainly by the Construction Manual, and it is possible to be installed The LED is also very nice and sharp It's solid and I'm happy with it The installation took about 4 hours to complete, with Wiring taking a long time to put away View detail
Happy!
It's affordable, easy to install, and you don't have to sacrifice the Loading Hook I am very satisfied with it If you are worried about installing it yourself, there is a person who uploads a video of how to install it on the net Please look for it and see if you can find it View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
I was able to install it on Kan Tan
It was cheaper than other companies, so I bought it There is no
Connector is also included, and is used to cut the Wiring on the MotorcycleBody It's easy to do without
View detail
It's the only way
First of all, thank you, HURRICANE
I'm wearing an EnduranceCarrier, so I need to find something to wear with it I was looking for it
Endurance products developed at the same time are designed to be worn together However, when I look at the blogs of our ancestors who wore the boards, I can't even call it a gap It was in the form of water and mud all over the place
The ones that are available elsewhere are not perfectly shaped and impossible to wear together
A friend of mine was concerned first Maybe we can go to the HURRICANE? So, my friend and I had a look at HURRICANE's blog, and we had a paper Then I licked it around so much that it was scraped and punctured
And if you look closely at the shape, you'll see that it's not only shaped to fit the underside of the Seat Cowl The Blinker is also in a position where it doesn't interfere with the Carrier and there's nothing growing underneath the board
And the installation is exactly the same as the way to install the Carrier's Bracket It was a thing to fix with M6Bolt between the Spacer and the M6Bolt
Grin, Carrier's Spacer is 39mm, this Fender Eliminator If the Spacer is 15mm and the thickness of aluminum plate is 3mm, put a 21mm spacer between them If it's a good calculation
So, Posh's 20mmQuantity for M6:1 Set of 2 Spacers of 2pcs. and 1mm thick flat Washer for M6 I was able to install it by pinching it and co-tightening it
As I wrote in my blog, the gap between the individual differences is 1mm thick and 1 cm wide Sponge I used a type gap tape and managed to make it work
The angle of the Number is not that far up, so it's a zero, and my friend has a GSX-R750 with an ACTIVE I'm wearing the thing, but it was more slanted that way
License lamp and Reflector are fixed on both sides, Lamp is quite bright and Tail The area around the License Plate appears to be faintly pink because it is mixed with the lamp light is stylish
Since the Blinker also fits inside a little bit, the Cover is Smooth, and it's easy to put on and off The license plate is high and the seat is underneath the seat, so it's in the garage Stress has been reduced as you won't run into any ladders
This is my second motorcycle and the first time I've ever been on a Fender Eliminator Thank you again, HURRICANE, I got the sticker too! (Naps WebShop (angry) ) and put it on the back of the Upper CowlFront blinker ( Quantity:Pair (for Left and Right) ), it is Large change satisfaction in conjunction with Handlebar
View detail
Good vibes!
I worried a bit because it is cheaper than other Manufacturer's items, but it is a good feeling that it can be installed safely.
After all the Fender Eliminator looks better!
I would recommend it..
View detail