Reviews
It's the only way
First of all, thank you, HURRICANE
I'm wearing an EnduranceCarrier, so I need to find something to wear with it I was looking for it
Endurance products developed at the same time are designed to be worn together However, when I look at the blogs of our ancestors who wore the boards, I can't even call it a gap It was in the form of water and mud all over the place
The ones that are available elsewhere are not perfectly shaped and impossible to wear together
A friend of mine was concerned first Maybe we can go to the HURRICANE? So, my friend and I had a look at HURRICANE's blog, and we had a paper Then I licked it around so much that it was scraped and punctured
And if you look closely at the shape, you'll see that it's not only shaped to fit the underside of the Seat Cowl The Blinker is also in a position where it doesn't interfere with the Carrier and there's nothing growing underneath the board
And the installation is exactly the same as the way to install the Carrier's Bracket It was a thing to fix with M6Bolt between the Spacer and the M6Bolt
Grin, Carrier's Spacer is 39mm, this Fender Eliminator If the Spacer is 15mm and the thickness of aluminum plate is 3mm, put a 21mm spacer between them If it's a good calculation
So, Posh's 20mmQuantity for M6:1 Set of 2 Spacers of 2pcs. and 1mm thick flat Washer for M6 I was able to install it by pinching it and co-tightening it
As I wrote in my blog, the gap between the individual differences is 1mm thick and 1 cm wide Sponge I used a type gap tape and managed to make it work
The angle of the Number is not that far up, so it's a zero, and my friend has a GSX-R750 with an ACTIVE I'm wearing the thing, but it was more slanted that way
License lamp and Reflector are fixed on both sides, Lamp is quite bright and Tail The area around the License Plate appears to be faintly pink because it is mixed with the lamp light is stylish
Since the Blinker also fits inside a little bit, the Cover is Smooth, and it's easy to put on and off The license plate is high and the seat is underneath the seat, so it's in the garage Stress has been reduced as you won't run into any ladders
This is my second motorcycle and the first time I've ever been on a Fender Eliminator Thank you again, HURRICANE, I got the sticker too! (Naps WebShop (angry) ) and put it on the back of the Upper CowlFront blinker ( Quantity:Pair (for Left and Right) ), it is Large change satisfaction in conjunction with Handlebar
View detail
Fits: YAMAHA Bolt CSpecifications, YAMAHA Bolt, YAMAHA Bolt
It's all clear
I wanted to make the back view of BOLT a little bit better for parenthesis, so I installed it It is the type which does not remove the Stop lamp of NORMAL Since the external LED stop lamp is not reliable, I was looking for the type that makes use of NORMAL Because I installed it without reading the Instruction Manual, it is Normal Because it became the installation with removing all the fenders, it had some difficulties I think this is a good product to protect because it also hides behind the back Just replace the NORMALCoupler and the License Plate Light It was made brighter by LED View detail
It's easy to install with a small ball
I installed it in the old Grom
Installation was easy and OEM Blinker was attached without problem
Although there are also explanations, Red's Reflector and triangle magazine Sealetc. I need to prepare myself and I do not have a Bracket so I bought another Bracket for Reflector and since the Wiring part of the Reverse side is all out, it would be better to think about something Waterproof measures
Texture was good and I was satisfied.
View detail
Good vibes!
I worried a bit because it is cheaper than other Manufacturer's items, but it is a good feeling that it can be installed safely.
After all the Fender Eliminator looks better!
I would recommend it..
View detail
Installation is easy
BMW I attached it to S1000R 2017 without problem
It is easy because it is wearing with basic Bolt 3 books
License Plate Light is also safe because it is OEM use
The accuracy is also high in the simple form but it will be saved if you can suppress Cost a little more
View detail
It's cheap. Installation is ... ,,
About License Plate Light This price is cheap.
I am satisfied with appearance also Refreshing and OEMBlinker without incongruity.
As for installation, Instruction Manual is a piece of simple paper. It was pretty much Large..
I think that it will be easier if you do not weld the Fender with Screw and Nut, but weld the Nut part etc..
And since Bracket in the License Plate Light part is a little Large, I think that I refreshed more if it is more compact.
I also recommend ordering the Made by HURRICANE Reflector.
View detail
I will recommend it..
When installing, it is necessary to remove Side cover and Blinker etc. once, but it can be installed easily with just labor. I am recommended because it is well-fitted and Cost performance is also good.. View detail
good
Worn on New Year 16-year Grom.
Because the new model has protrusions in the ass, this product which is not empty is not ordinarily attached, but it will be managed by processing.
Marking the protrusions, drill a standard hole with Drill and Cut to square in the Grinder, the position of the mounting hole does not change at all and it will be attached properly.
Work time including Cut is about 30 minutes.
It is somewhat troublesome to have a hole to escape the electrical system, but it is somewhat troublesome, but if you are used to DIY and have a tool, it is possible to make it cheaper than the new type Fender Eliminator, so it is Recommendation for those who can do it.
View detail
Early! Cheap! Easy!
Remove NORMAL while reading Papapa Instruction Manual, Complete installation on papapa.
It was over in a short time.
There is no Bracket attached to Reflector, so it is necessary to prepare separately if with Reflector.
Because NORMAL is quite heavy, I refreshed it.
I think that it is also possible to attach Helmet holder and pole stands after a bit of remodeling.
View detail
Cospa Good!
We are on the S1000RR of MODEL 2016. Since I mentioned 2012, I thought that it might not be attached ... but it came with Exactly.
It was the cheapest S1000RR Fender lessKit I was looking for, but I am satisfied with my firmness.
Not only this Fender lessKit, but also those who want to port NumberHolder of bmw at the same time, it is considerably difficult to remove Number Holder unless there are thin Pliers etc.. As I saw in the third photo, I took it about 3 hours using the slotted screwdriver and I could do it off.
I'm not complaining about this product, but I think that one who is bought should pay attention to the following points.
- Angle of Number is constant and can not be adjusted to my favorite angle.
- A bit heavy
Is it a lol?
If you do not stick to the angle it will be cool enough by this ^ ^
View detail
Almost satisfied
Compared to other Fender Eliminator Kits, since Blinker is inside Number, there is sense of Slim and Parenthesis is good. Although I removed Tandem Footpeg, I was troubled by the place to install the Helmet holder and I do not want to stand out, so I attached the Helmet holder to the NumberReverse side of the Fender Eliminator Kit. Machining was easy because Material was Aluminum. View detail
Firm, design is also good!
Even without attaching License Plate Holder, it can be attached without processing. It looks SMART, I thought that it fits this Motorcycle well. Wiring was saved because 2-pole Coupler was also included. Installation is easy. View detail
It is Cool.
I wanted to make the circumference around Rear so I exchanged it.
Image changes quite a bit after replacement.
I think mud bounding is equivalent, but I do not mind because I do not ride on a rainy day.
View detail
As expected!
Normal fender I bought it without being able to endure the overhang which is not too much.
Motorcycle came by connecting several, but it was my first time to convert to Fender Eliminator
It was easy to install because the making is solid.
Just to wire, the removal of Rear Fender (Although it is not absolute) Necessary
I had not taken off yet so I took Large minutes time there.
Also, I do not know the competitor's Fender Eliminator,
The hole that allows Wiring to pass through the company is surprisingly large, so it seems that water intrudes into Rear cowl as it is.
Initially I tried Waterproof by plunging Black Bus coke into Wiring hole and Blinker hole.
Wiring of License Plate Light was the opposite of Instruction Manual, but there was no problem just by replacing it as written in the Instruction Manual. (I think that because Waterproof? Cover is attached to the Female terminal of Bullet Terminal and it is not attached to the Male terminal, it does not wind up even with an insulation tape.)
View detail
Fits: KAWASAKI Z250SL, KAWASAKI NINJA2 Helmet50RSL
Is it because it is cheap?
I bought it because it is cheap
250 SL is to remove the winker-ASSY
It is a strange Large strange
WiringCoupler - is also hard to remove
A few centimeters winker from Norma will also extend
It's a waste of a slim car body.
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
HURRICANEFender Eliminator Kit
Manufacturer that needs Connector Processing Many are Manufacturers that need to process completely, Extra Processing Not Required is absolutely the choice without any wiring processing. The mounting position is also perfect, anyone can install it if you can do daily maintenance. View detail
Replaced
It is a replacement from DAYTONA. Building is Simple Rear around Rear and Parenthesis has improved. I still have not run wet road, but muddy flew back to DAYTONA before, so this is more than that ^ ^;
It is comparatively light compared to DAYTONA (^^)
View detail
Fits: YAMAHA Bolt CSpecifications, YAMAHA Bolt, YAMAHA Bolt
Installation is completed.
I could easily install it even with amateur myself. But electric Wiring had a different color, so it took a while. Others was a product without complaint. View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Refreshing with Favorites
It is still light with Aluminum's point as it is a thick Stay Easy to install The LED's License Plate Light is also solid and Wiring can be installed without any difficulties. It is my favorite. View detail
I bought this thing to look more sporty. There is no problem with the screw holes and design. attractive and sturdy design. at first I used the oem signal lamp. but when riding with a pillion, pillion foot are exposed at the oem signals. then I change at
I bought this thing to look more sporty. There is no problem with the screw holes and design. attractive and sturdy design. at first I used the oem signal lamp. but when riding with a pillion, pillion foot are exposed at the oem signals. then I change at a much smaller signal lights. There are no more problems. Another problem at license plate lights. When shook, the lights will not go on occasion. so I remove license plate lights. View detail