Reviews
It's good, but it needs improvement.
This is a report on the Z900RS.
The texture is refreshing and good.
The hole to pass the wiring of the Blinker and License Plate Light is large, and water enters under the seat when driving in the rain, and ETCBody etc. become dirty.
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
A satisfying dish
The InstallationInstruction Manual is a little hard to read, but it didn't interfere with the installation.
It looks great and I'm very happy with the Large.
View detail
Perfectly made, I'm happy!
I installed it on my 2010 CB1300SF. it took me a long time to remove the OEM fender and the tail cowl was cracked, but I managed to remove it. The installation itself was easy and no problem, but if I had to say, I would have appreciated if the instruction manual was a little clearer. View detail
CostValue High!
[How is it used? 2 weeks after installation
Was the one you received as per Image? It is almost as Image.
Was the installation difficult? I think it's relatively easy to install even if you don't have much skill.
How was your experience with it? I really like the angle of the Number.
[Included Parts:were they on? Not particularly.
[Was there anything that disappointed you? Not particularly.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer It was difficult to pull out the coupler of normal fender from between the frames, so I cut it off. When you install it, you can pass it through without any problem because there is Bullet Type Terminal in the middle.
View detail
Fits: HONDA CBR250R (2011-), HONDA CBR125R, HONDA CB250F
Number one for compactness and stylishness!
I bought this to install on my '14 CBR250R late model.
The mounting holes are open for both the first and second semester, so it can be used with either.
When I purchased this kit, I compared it to the Fender Eliminator Kit TYPE 2 made by False Design.
Because it is the commodity of the appearance which is very compact and stylish with the License Plate Light which is not conspicuous in the Small Type of LED, both were comparing and examining, but when it installs NumberSIDEBlinkerCompact made by Active at the same time However, I hesitated at the price of double of Made by HURRICANE, so I decided to process and install here.
[Contents] The Fender Eliminator Body is divided into 3 parts, LED License Plate Lamp, a set of mounting screws & Rubber molds at the rear end, tape to cover the unused holes, and instruction manual.
The product is made of 3mm thick aluminum material with good fitting and finish on each part.
Anodized is also applied evenly and beautifully.
The manual does not describe the disassembly around the Tail as carefully as the service manual, but you can get the flow, so if you don't want me to teach you how to do it, it's not a problem.
The installation of the Fender EliminatorBody is illustrated and very easy to understand.
I didn't need the OEM Blinker mounting base, so I cut out the Number mounting parts from the same thickness aluminum plate and made them myself as shown in the attached image.
Quantity:I could cut off the Blinker mounting base of the Set product, but I don't want to be able to put it back when I need it…
One of the reasons we chose this product was that it was structurally easy to manufacture this part.
Easy to install. The LED License Plate Lamp Connector is also Bullet Type Terminal so you don't have to worry about wiring.
However, since there is no clear positioning for attaching License Plate Light, please be careful.
Please refer to the attached image of the figure installed together with the Number baseReflectorW122&Active NumberSIDEBlinker made by the company.
Personally, I think that there is no other Fender Eliminator Kit for MC41 that is so refreshing.
The construction is robust and there is no concern about damage from vibration.
The attached LED License Plate Lamp is also very bright in both brightness and irradiation range.
I think that the person who is concerned about the mud splash does not make Fender Eliminator in the first place, but I think that it is still better in terms of the position and angle of Number.
By the way, when the kit is installed as is, the Number installation angle is about 40-Degrees. (Depends on the suspension and individual …)
But it's not without its concerns.
First of all, because it is exchange for stylishness, it is unavoidable, but the wiring of the tail circumference which was settled in OEMFender is translated to move in Fender Eliminator, but it is very small in space.
I'm adding terminals and Wiring myself. (Please refer to the diary) And even more so, I can't afford the space.
So, be careful not to squeeze or pinch the Wiring or Connector during Tail cowl installation.
As for flooding in the Tail cowl, it looks like it will be more than OEM…
If you are thinking of using a short LED Blinker etc. attached to the Blinker mounting base because there is a mounting base behind the Number, it may be hidden by the Number and become difficult to see, so it is necessary to check.
Also, the attached screw is too long even if the individual difference is considered.
The nut with looseness prevention is put in the body side of all four installation screws, but it is strange to turn to the tightening position.
It's not a problem for installation, but it's awkward to have four screws sticking out unnaturally in the tail cowl, so I'm planning to replace them with screws of appropriate length.
If you like this design and you can understand Demerit, I think you can buy it without a doubt.
View detail
I want Reflector on it too.
I don't like NORMAL Fender of ZX-10R.
So, I considered making a Fender Eliminator and went to various manufacturers.
As a result, I chose HURRICANE's Fender Eliminator Kit, including the cost and design.
I bought it because I thought the price was fairly common.
Installed as soon as it arrived.
I'm a novice, but I was able to install it quite easily because it came with an instruction manual.
The trouble would be when you remove the long bar that holds the current Fender in place.
It didn't come off at all, so I hit it with -Driver and Hammer to remove it.
On the downside, as others have written.
There is no Reflector, so you will need to purchase them individually.
In addition, the angle is docile, and the board Gold side where LED Light is installed is
Is it that there is a little gap between the vehicle and the body?
Other than that, no complaints.
View detail
The OEM Mudguard wasn't cool, so I replaced it!
The OEM Mudguard wasn't cool, so I replaced it!
Rear area has been refreshed. (^-^)
*ReflectorLicense Plate Bracket is required separately!
View detail
Up type muffler beware!
It is a universal blinker. When I installed it, I was relieved to find that it is not allowed to use a universal blinker, because it has a small blinker.
When I installed it, it hit the Yoshimura Exhaust System Up TypeR-77SCYCLONE and I had to change the blinker to an ultra-small blinker.
Also, the gap between the License Plate and the Exhaust End is only about 5mm.
The Down Type Exhaust System should not be a problem, but the Up Type muffler should consider the Blinker's Large size before purchasing.
The product is easy to install and cheap.
But in the end, I ended up paying the same amount of Gold as the more expensive Fender Eliminator.
View detail
Looks neat!
I purchased and installed it in order to refresh the GSR750's gears
I'm happy with the cost and the build quality
Personally, I think it would be better if the angle of the Number can be adjusted
I modified another car's Normal fender for rainy day driving
If you don't know about the GSR750, I think it looks like a NORMAL
View detail
All in all, I think it's a product that is worth the price
This is a Fender Eliminator Kit for the GSX-S1000, order it now I haven't received it yet, so I don't know how it feels or the texture of things etc
As you can see in the product description image, the position of the blinker is a little bit far from the number, so I'm worried about it Some of you may be
Also, you need a reflector, so it would be nice if you could include one with this package
View detail
It's a good, solidly built product
It was inexpensive, well-built, and easy to install
The other Fender Eliminator has a gap between it and the stop lamp and I don't like it very much is not, and this product is great because it doesn't have that, and it doesn't feel different!
I'm glad I refreshed the rear area and purchased it
View detail
It's a good costumer and looks great
When I bought the GSX-S1000, it was my first Custom for the HURRICANE I threw in the Fender Eliminator Kit
The installation system is perfectly fine, and the Installation Instruction Manual is included I think it can be installed easily in about 30 minutes if you do it while watching it In addition, the cheap price and the wiring process of the position lamp is very easy to install I liked the fact that it was unnecessary
The only complaint I have is that the Reflector is a Quantity:The point is that it is not a set and must be purchased separately
Recommendations for those who don't care about the brand, and who care about the costumes I think it's a product
View detail
○
I installed it in MODEL of 2020/2/20 release, but it can be installed and used without a problem
Naturally, the bounce is great
View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
Clean around the rear!
GSX1300R HAYABUSA 10 years old, installed for use in North America
It's pretty neat around the rear! I don't like the raggedy OEMRear Fender, and the Fender We recommend "Made by HURRICANE" which is the cheapest Eliminator Kit available It is
Installation is easy if you can remove the rear cowl, Couplet-on for easy installation It is
In my opinion, I would have liked the Number angle to be a little higher
It also comes with a License Plate Light, but it's not that bright
It doesn't have a Reflector, so you need it separately for inspection
Overall, the Rear area is cleaner and the Number is angled, which makes it look very It gets better
View detail
Fits: YAMAHA MT-09 To Racer, YAMAHA TRACER900, YAMAHA TRACER900
Cannot be used by those who wear the side case
Side case and Blinker interfere with each other, so you can't use it
(I put it on as a Large mod.)
If you don't use the Side case, I think it's a good thing it's cheap
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
Cool
Reflector is the license plate base of CB400SF (sold separately) I purchased a The assembly, wiring, etc., can be installed comparatively plainly by the Construction Manual, and it is possible to be installed The LED is also very nice and sharp It's solid and I'm happy with it The installation took about 4 hours to complete, with Wiring taking a long time to put away View detail
Happy!
It's affordable, easy to install, and you don't have to sacrifice the Loading Hook I am very satisfied with it If you are worried about installing it yourself, there is a person who uploads a video of how to install it on the net Please look for it and see if you can find it View detail
Fits: SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA)
I was able to install it on Kan Tan
It was cheaper than other companies, so I bought it There is no
Connector is also included, and is used to cut the Wiring on the MotorcycleBody It's easy to do without
View detail
That's good!
I wanted to Refreshing Rear, which was feeling heavy But I don't want to spend that much Cost
You can use the OEM Blinker and License Plate Light as it is I'm glad I did
I'm satisfied with the image
View detail
It looks good
User vehicle inspection failed due to light leakage from the license plate light, Touch pan I painted it and it passed I could see the white LED from right behind View detail