Reviews
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Yamaha FZ-09 Handlebars
Awesome. Handlebars arrived in 5 days. Product was packaged well. Looks like it will work great with my FZ09. Great service. Will buy from again. View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
XSR900
Great handlebar for xsr900. Install was great and easy. Took about an hour to do. Cheap and very fast shipping. Highly recommend View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
I was able to buy it at a discount.
As other users have mentioned in their impressions, there is a possibility of thumb damage when fully locked.
I also eliminated the problem by biting the Washer into the Handlebar Post to bulk it up.
Since the handlebar is lowered, the clutch cable and brake hose must also be reworked.
Position-wise, it will look good, but it will be a little heavier since it will be made of steel instead of aluminum handlebar.
In my case, I was able to buy it at a reasonable price, so it's a great cosmetic product!
View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Lean forward.
I installed it on my Trident 660.
This is a special product for MT-09, but it can be installed without any problem.
You will need to drill holes in the Switch Box.
For the Clutch SideGrip, drill a hole on the opposite side of the original hole and fix the grip.
It's fun when you're doing sports driving because you can lean forward a little.
I don't like to stay up too much, so it was just right.
View detail
Would buy 10x again!
Perfect bars for my use. Handling was good, more tuck but not bad on back or hips in new position, more than comfortable on my wrists too. Be warned you will need a plan on moving the cluster over with an aftermarket plate (probably). View detail
Hurricane Fat Swallow Bars on XSR900
Fit is perfect! Drops the riding position a little bit but is not that drastic to the point that you will hurt your back. The pre drilled holes line up to the clutch, brake and throttle controls perfectly. I also purchased the Hurricane clutch cable since the stock one will be a tight fit because of the solid bent portion hear the handebar side. Also, The stock bar end weight will not fit as the hole is 18mm so I am going to purchase a separate bar end weight soon. Without the weight theres a bit more vibration as compared to stock. View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Can be mounted on cb250r
I installed it on CB250R. The interference with Tank can be avoided by matching the existing hole on Axel side.
Clutch Side needs to be decided carefully, but I was still able to dodge it with Limit.
This is an ideal forward leaning position, but it would have been 5 stars if the width was a little narrower.
View detail
sdgt
I bought these handlebars for my 2016 FZ-09 to replace stock handlebars. The installation is very simple, but there are some problems. The master cylinder hinders most aftermarket windshields. I have to remove my PUIG windshield to install the Hurricane Fat Swallow handlebar... ---------------------------------------------- I purchased these for my handlebar 2016 FZ-09, to replace the stock handlebar. Installation is very simple, but there are some problems. Brake master cylinder prevents the windshield of most aftermarket. I have removed my PUIG windshield for installation Hurricane Fat Swallow handlebar .... Powered by Google Translator View detail
Awesome Product, but a few issues
Purchased these handlebars for my 2016 FZ-09 to replace the stock handlebars. The installation was very straight forward, but there were a few issues. 1. Stock Brake Master Cylinder gets in the way of most aftermarket windscreens. I had to remove my PUIG windscreen to install the Hurricane Fat Swallow handlebar. 2. Throttle cables had to be routed above the brake reservoir to prevent the throttle cables from binding. 3. Had to grind some of the plastic trim around the ignition to provide room for the clutch cable. 4. The stock brake line ends up on a 90 degree bend using the factory setup. Luckily, I'm upgrading the brake lines to braided stainless steel and will route the front brake line differently. Otherwise, you will want to disconnect the front brake line and route it differently. Overall, I am very happy with new sportier ergonomics on the bike that the Hurricane Fat Swallow handlebars provide. Just be warned that you will have to make some modifications for the clutch and throttle cables and be very mindful of the front brake line. View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Halfway to the front leaning posture
I am used to leaning forward in a forward leaning posture, but I can't hold my upper body in a fixed position, and I have a hard time holding onto it It will Once I got used to it, it was fine and easy to operate, but at first it felt indescribably strange, STD I decided to change the Handlebar because it feels like I'm on a wr and it's wide enough for me The OEMOption buffalo handlebar would have been better View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Basically, I buy what I like and I rate it highly
Used for THE KING OF MT
I think it can be attached by shaving Cowl and changing the brake hose handling It was done
It involves some processing, so you can either get a Shop mechanic to do it for you or do it yourself
Customise at your own risk anyway
View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
It's a front load
7cm forward and 3cm down, so it's a bit of a front load
This makes Corner's Breaking easier to control and easier to bend It was
Long distances can be a pain in the hand
It is Exclusive Design, but it is better to change the Clutch Cable's pull lever Stress is gone
View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Used in XSR700
I used it on the XSR700
To install, remove the headlights from the bracket and use the Throttle Wire You will need to adjust the handling of
Other than that, no problems
The lower Handlebar makes cornering a lot of fun
In my case, I am also wearing Rear Sets, but on a touring of about 200km, I have to use them, especially on my hips and shoulders did not hurt
View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Excellent fit for XSR700
These fit perfectly on my XSR700. The pre-drilled holes lined up perfectly and fitting the bars was very straight-forward. The bars give the bike a much more aggressive feel but are still really comfortable. They are a huge improvement over the stock bars. View detail
Perfect fit on my XSR900
perfect fit on my XSR900 Dont need to make hole for switches Easy to install took me 3 hrs to DIY which is my first time to switching handle bar. But need to buy a set of handle grip and a set of bar end. View detail
Love these handlebars!
Purchased these for my XSR900 as the stock bars are a bit too upright for me and I didn't want something too aggressive. These are the perfect mix! Gives you a more forward riding position while not compromising comfort. Feels better in the turns and gives the bike a great look, in my opinion. I also liked that they had the holes already drilled for the controls so installation was very straight forward. Very happy with the purchase. View detail
Outstanding!
I got these handlebars for my XSR 900. After doing just over 1K miles with them, I have to say I'm really pleased with this mod. Although you will lose some confort if you go for lower bars, this option sits right in the middle between the standard rise and the extreme position you will get with clip-ons or with the yamaha OEM clubmans (which at least IMO, are too far down). Needless to say the bars look great on the bike and they will improve the sporty feel when riding without hurting your back nor wrists. Another important thing is that they are quite easy to install. The clutch cable needs to be rerouted slightly to avoid being clamped by the forks, but other than that, nothing tricky about these. Note that the inner diameter is different from stock bars so you will need new bar end weights. Also, if you are in the EU, bear in mind that you will have to pay import duties (i think around 50€) at delivery. View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Optimal Position!
Since NORMAL has height and width, I personally wanted to change it to a Handlebar with a little more Sporty feeling so I bought it.
The feeling attached was more than I expected with Sporty Position without complaint.
The only point to worry about is that it is in full lock state that if the thumb on the in side does not hold handlebar, it suits A little painful eye.
Handlebar has been drilled, Handlebar itself was attached easily, but in 2017 MODEL, to attach the attached Spacer for Meter movement, since Metall Bracket's Bolt is welded so that it can not be removed, it is scraped off Processing is necessary. (However, if you do not process the Front panel before Meter, you will get a gruff on Meter Bracket, so you need to cut it carefully. )
I do not want to cut the Front panel, so I used POSH Faith Posh Face's Billet Meter Bracket and Universal's Bracket together.
Since the product was good, I think that if possible we can take measures for the above two points.
View detail
great handle bars
Very pleased with these handle bars. In my opinion the riding position has improved. This item is completely bolt on and fits right in, no modification needed. Overall great product. I do recomend it. View detail
Fits: YAMAHA MT-09, YAMAHA XSR700, YAMAHA XSR900
Sporty Handlebar posture is running ImageUp
I always wanted a Handlebar position that would fit even shoulder lower
I also considered purchasing the Separate Handle Kit,
Swallow handle is cheaper and it seems easy to install so purchase
At the Handlebar position as I imagined
The sense of stability of posture during high speed driving has improved remarkably
However, the installation was more than Large change
After handlebar exchange Throttle, Clutch Wire handling
It became rather heavy as it became tight.
In order to make both of them beautiful, we need a Fight light Unit
It may be better to remove and change Route
View detail