Reviews
No complaints at all so far.
I installed this bike for Enduro race on my KLX230R. it is fixed in two places at the handlebar and bar end to protect my hand and lever. the material is plastic and there is no gold frame, but I have used it for about 2 years and there is no trouble such as lever breakage. There is no trouble such as lever breakage after about 2 years of use. Since it is a universal product, it is necessary to cut some parts of the frame to make it fit perfectly, which is a little time-consuming. However, since the material is plastic, this is relatively easy to do. View detail
Exactly to Hand guard for the first time
What made you decide to buy?
I bought this product because I was advised by my friends that I should have a hand guard for off-road racing. I've never used a hand guard before, so I didn't know how to choose one, and I chose this one because the price was cheap and the reviews didn't look too bad.
How was your experience with it?
I fell many times during the off-road race and the hand guard did not break and protected the lever very well.:It's Plastic, but it seems to have some strength to it.
Also, Material that seems to have strength.:Being lighter than the aluminum Hand guard, the Handlebar also felt lighter to handle.
Was the installation difficult?
I put the hand guard on for the first time, and it was Large strange to fasten the clamp part while dodging the wiring and so on.
【Please tell me the installation point and hang】
At first, the clamp part didn't fit on the Handlebar at all and I was in a hurry, but it's plastic and flexes well, so you can bend the hand guard to fit the shape of the Handlebar without any problems.
[Was the Instruction Manual easy to understand?
The instruction manual is in English version, so I don't understand the explanation well. I was able to install it with only a diagram because there is a diagram in every process.
[Included Parts:were they on?
All the necessary parts for installation are included, and the inner diameter of the handlebar is wide enough to fit most large handlebars.
[Was there anything that disappointed you?
None in particular. The strength was enough for the price, so I'm satisfied with the cosmetics.
Do you have any wishes or improvements you would like to make for the Manufacturer?
It's a foreign product, so I thought it would be like this.
[Do you have any products to compare it to?
None because it's my first product.
View detail
Cosma Large.
Something to protect your hands from the cold but not tacky in the winter, Aluminum bones (Grip Guard) If you don't want it, this is definitely Recommendation. The cost performance is very good. View detail
It has a nice, light handlebar feel that the Gold genus Guard doesn't have
? Reason for purchase
When riding off-road on the KTM Free ride 250R, you can put your hands on stepping stones, trees, etc I was looking for a Hand guard to protect me from
The conditions for doing so are There's no core in the genus Gold stuff
In the past, when driving off-road, such as with Enduro, we have had to use the It is equipped with a Hand guard of the type to protect with aluminum or other I did
However, it's only because of the considerable weight of the Gold genus, which makes the Handlebar feel heavier and I was very tired when I was running on the rough terrain where the Handlebar often swung I did
Therefore, this product was chosen because it is light but has a certain degree of protection performance Installed
To prepare for Brake/ClutchLever damage due to a fall, the ARC's unbreakable Lever(Material):Plastic) would not be a problem to install, it was decided that it would be fine
? installation
A normal Pipe Handlebar should be able to be installed with no problem
I used a bolt for Clamp and Handlebar End Therefore, I installed the Pierced Type Grip which has a hole at the end in advance It's easy to leave behind
Depending on the type of vehicle, such as a TRAIL vehicle that has a lot of switches, there may be a Switch box or a MASTER You may need to fine-tune the position, etc
? feeling of use
We were able to achieve both a light handlebar feel and protection at the same time It was
Clearance with Lever etc. is also sufficient for 1 or Quantity:The 2pc finger control felt fine for Space, even with 4 fingers, of course
For Small stones from the car in front and Small branches on the woodland course, etc Protection performance is also adequate
However, unlike the Hand guard made of the Gold genus, it will break in the event of a fall (Lol)
I've seen this product in clean, unbroken condition, as I usually fall down multiple times in one race It was only once ^^^;
I understand that this is just the nature of the product
Well, the price is so low that I had to replace it several times when I reached the limit of the Repair
In general, I'm happy with the cosmetic results and the color of the Orange matches the Frame So I like the OEM PowerParts feel
View detail
Other than OEM Knuckle guard
I installed it in DL 1000 V-STROM 650.
Knuckle guard is on sale from SEA BASS with OEMOption, but Design seemed to be unbearable, so purchase Poly sports' Knuckle guard that was also attached to TDM 900 before..
Since it's a big deal, Choose Suzuki yellow according to Body color. I thought it was a bit flashy, but it is a good feeling.
Since the Body has some flexibility in the installation, I installed it while adjusting it well. Because the Clutch lever slightly interfered, I shifted the position of the Holder to the center side by 5?.
As Demerit, when installing this Knuckle guard, the OEM's Handlebar weight needs to be removed. Nonetheless, even if you remove Bar Weight, you can run without any problems.
I have been waiting for a while because the ordering period since ordering is long.
View detail
I like it very much.
Among Closed type of All resin, overwhelming Cost performance.
There is not much fancy, but the Guard part is made of 1 Parts, so it is harder to break than what is made of 2 Parts.
Material If there is, it will not crack unless it is used quite a bit.
I think Guard strength is necessary and sufficient.
Also, as it is not quite light, it is better not to have any influence on Handling.
If there is one drawback, it can be said to the general resin hand guard, but the sense of fixation is weak and it is easy to twist and turn around.
View detail
Knuckle guard also suits On road motorcycle
I installed it in the TDM 900 and already love it for about 10 years since I bought it.
The hardest thing about Riding in the cold season is the cold of the limbs. So, I installed a Grip heater on a thick Winter Gloves, and it will be, but when I run on a highway, the degree of cold weather protection is so cold that there is no effect.
I think that wind protection measures are more important than anything to prevent cold in Motorcycle. Recently many ManufacturerOEM's Knuckle guard has been lineuped, but Universal products are not so many.
Also, OEM's Knuckle guard is often undesirable in Design.
Poly sports's Knuckle guard is almost mountable if it is a Pipe Handlebar Motorcycle and design is also Sharp so I think it will fit various Motorcycles.
Although it is not a very large Guard, it is Large enough to hide his hands, and the running wind is surely prevented.
Even if installation is somewhat uneven, because it is universal, I think that if you make delicate adjustments Large I think many things are durable, but if you need to prepare Spacer separately, such as Washer and Color.
Also, when installing this Guard, depending on the shape, I think that OEM's Bar End will be unusable.
Quality has been used for more than 10 years, but there are no cracks, no cracks, no color fading has occurred. I think that it is a Knuckle guard that not only adaptive Motorcycle and MOTARD series but also SportsNAKED suits.
View detail