Reviews
It's crisp and clean.
This is a change from OEM.
The installation can be done without too much difficulty if you have experience in such work as replacing the clutch lever, since there is a translation (please enter hereManual).
Also, while installing it, I felt that the accuracy of the cutting process may vary a bit, and you may be dissatisfied with the Quick Adjuster for Red and Blue. The color will deteriorate under ultraviolet light while in use, and the color will fade, but if you are considering purchasing these as Custom, please be aware of this.
Grease is also applied to the bolt that fixes the lever from the beginning, and the handlebar is fixed with a clamp system, and the screw is very precise, so it was installed comfortably.
The clamp that fixes the handlebar is a little hard plastic material, so there is a possibility that the entire clamp may rotate when it falls over. If you are concerned about it, you may want to change to RubberMaterial.
As for the feel of the operation, as per the Title, it is snappy and sharp.
If you want a direct feel from it, I think you can further modify the Sleeve in the Thailandico fixation area.
Even with the Sleeve position in its normal state, the OEMLever comparison is better, so I felt that the Point is a point of preference depending on how a person uses Clutch.
I wish I had not been stingy and purchased it earlier, as it is one of the other Items that can be fine-tuned for Lever position.
View detail
Used for RADIPON MASTER
I purchased this product to install a Guard made by another company.
The handlebar is very well made, and the handlebar is fixed with 4 screws, so even if it loosens a little, it is not likely to become defective immediately.
This time I installed it on a Fat bar and was able to install it without any problems.
I put it on as it says RightLeft on the product, but there seemed to be no difference in the shape.
I would like to see if it is sturdy enough, since I think this kind of thing plays a stronger role in resisting impact by rotating rather than guarding against falls.
View detail
To avoid breaking the Lever
I installed it to enjoy Motorcycle in various Situations in the future.
Installation, etc., is not a problem at all, as it is often seen in videos, etc.
However, if you need to open the throttle cone and want to process it nicely, you need to have tools.
I think it is easy to work with.
After installation, the motorcycle looks tighter and I am satisfied.
I don't want to feel the effects as much as possible, but it has become a talisman.
View detail
Expensive but good product.
I bought it for a place where I really want to fix Wiring.
It's Titanium, so it's expensive, but I'm satisfied.
View detail
Good to have a variety of colors to choose from.
This one is good because it offers a variety of Coloring choices.
Both Cx and sx bars come with Pad as standard, but the Black is Quantity related to the color of the bar.:Set
Inevitably, every time you buy a bar, Black's Bar pad will accumulate in droves! 。
There is almost no profit to be made selling them on Mercari or Yahoo!
I would like to be able to choose the color of the Pad anyway, but I think it would be better if the Pad is treated as an Option like the comp bar and the unit cost of the Handlebar is lowered.
View detail
Fits: KAWASAKI D-TRACKER, KAWASAKI KLX250, Others , YAMAHA WR250R, YAMAHA WR250X
There are some good things that only a comp bar can do.
I put a MOTARDMedium comp bar on my CRF250RLY50.
I had worn cx bar mx-123Blue before, but I thought it would be more comfortable with a little more aperture in terms of position. I decided that the comp bar would fit CRF250RLY50, which is not so strong and rigid, and bought it.
As a result Large was the right answer
The position, moderate rigidity of the handlebar, and coloring are perfect.
View detail
as necessary
This is the purchase of consumables that are included with the exclusive product.
There is also a Dirt run, and I was a little concerned about the Chain coming off, so I bought it.
View detail
For dress-up purposes.
[How is it used? Touring Sometimes I want to go into the mountains.
Was the one you received as per Image? Yes, it is neither large nor small.
Was the installation difficult? Very easy.
How was your experience with it? It's spring and the weather is nice, so I don't feel the effect of windproofing etc., but it looks better! 。
[Included Parts:were they on? Mounting Bolt
[Was there anything that disappointed you? There is none
Other items that would be helpful
Since the Armour Hand Guard Bend was originally installed first, it naturally fits perfectly.
We will go into the mountains and see if this works.
View detail
Stability only possible with Fat bar
This is a Review at least 6 months after purchase.
Quantity:Pair (for Left and Right) Fell multiple times on Tarmac in (SlipDown type) were, but there are no visible signs of breakage or bending, and the feel of the product remains the same.
The length of the bar is 800mm, which may be a little too large for some Japanese, perhaps due in part to the length adapted to the physique of Westerners. I use it with the bar packed.
Motocross athletes often use them without filling them these days, so if you take that into account, you can use them without any particular concerns.
View detail
Fits: KAWASAKI D Tracker 125, KAWASAKI KLX125, KAWASAKI KLX150S, Others
Used for DT50.
I'm 184cm tall and the OEMHandlebar was making me feel like Curve was repricing, so I changed it.
Operability has been improved.
View detail
Installation review
I bought it to change the rear luggage rack, and contrary to my worries, it fits well. However, you have to separate the air duct and pull it hard from the inside with pliers to make it fit all the way.
There is no difference from the other parts and the finish is clean. I dressed it up at a low price. -------------------------------------------------- -------- I bought it to change the rear luggage rack, and contrary to my worries, it fits well. However, you have to separate the air duct and pull it hard from the inside with pliers to make it fit all the way. There is no difference from the other parts and the finish is clean. I dressed it up at a low price. Powered by Google Translator
View detail
Very beautiful Red
I like the design and practicality.
It can reduce finger pinching in the event of a fall.
View detail
Cool
This is Cool, although I honestly don't know how effective it is.
Red is good.Color:Red is unexpectedly suitable for Gray Motorcycle.
View detail
Mounted on ADV160
I put it on for spring, summer and fall.
The design is good, and the small size allows for good ventilation.
It rarely runs Off, but it suits ADV!
I chose Black, but a matte color would give me more options.
View detail
Fits: HONDA CRF250L, HONDA CRF250M, HONDA CRF250L(S), HONDA CRF300L
Hokkaido Tour
this summer
Hokkaido Touring Schedule
Little by little, we prepare for that.
Removed for forest road touring
with ScreenKakeTamaMaju I can't mock up comfortably.
Easily removed by PointUp??
View detail
Fits: HONDA CRF250L, HONDA CRF250 RALLY, HONDA CRF1000L, HONDA CRF1100L
Not that I'm complaining.
I have not tried riding without the rubber, but I think it is a good solution if you remove the rubber. Also, the quality of the product is good, and compared to Chromoly products, the Material:I think it's also good that Parenthesis is made of aluminum, and as a footpeg, it's quite wide, so I felt it's good that my feet don't get tired easily. View detail
Great product, great price, easy install
Easy install, took only 15 minutes,went on with no issues. Very good quality and really makes for a much more comfortable ride. Being a 185cm tall rider the 30mm additional height was exactly what I needed for those times I need to be standing up through the rough technical terrain. I would definitely recommend these for taller off road riders.The zeta clamps are exactly what I needed at an affordable price.I can easily recommend these risers.It's worth the money in my opinion. View detail
Fits: HONDA CRF250R, HONDA CRF450R, KAWASAKI KX250F, KAWASAKI KX450F, KAWASAKI KLX450R, KAWASAKI KX125, KAWASAKI KX250, HONDA CR250, HONDA CR125
Anodized is beautiful.
MX-123 was installed on a CRF250.
OEMSeat is modified with 3cm up high seat and 14mm up spacer to get the best position.
View detail
Fallen cannibals
I use Retractable Lever, but I bought this one just in case.
I have not yet encountered a situation where I can install it and see how it performs, so I can only judge it by its appearance.
Cut-out products are quite satisfying just to install.
When installing, make sure that the Clutch Side and Brake Side are facing in the correct direction, as it is indicated on the package which side it is on. Also, there is no indication of which way is up or down. Use your own experience to cover it.
View detail
Windproof effect.
There are many videos on youtube etc. for installation, so you can install it while referring to them. As for the windproof effect, it has a windproof effect from half of my face to my chest area. The Demerit has a screen that creates turbulence, which causes the head to shake when the wind blows against the helmet. The height and angle of the screen must be adjusted as often as possible to avoid turbulence. It is not enough to just raise the screen, but it is better to adjust the image so that the turbulence hits the entire helmet and the wind pressure is dispersed throughout the helmet. It is not easy to adjust the helmet, but I like it because it reduces fatigue during long tours, and it also makes the helmet look more like a travel helmet. View detail