Reviews
tmr mjn32 Slow Jet
Purchased to change Slow Jet from #22.5 to #20 for tmrmjn32 for cb400sf from High Octane Spec. to Regular Specification.
As I mentioned before, it's well made.
I have bought other Jet of the same model, but the accuracy is incomparably precise.
However, since it is a 4-cylinder, it was quite expensive to buy 4 of them, and it was a bit difficult for Wallet to afford them.
View detail
tmrmjn32 sj22.5
I have a tmrmjn hanging on my CB and bought #22.5 because the one used was #25 and it was darker near the Idol
Effective, Idol stabilized.
View detail
Stock would be a lifesaver!
A 4-cylinder would cost just under $3,000 at a top ranking, but rather than price trends, WeBig was more helpful in having a decent inventory of major Pilot Jet models in stock.
I purchased several items at once, and I appreciate that you could deliver about 4Ranks at once.
View detail
Used for YOSHIMURATMR-MJN
The MJN suspension for the ZEPHYR1100 was PJ27.5, so it was too thick in the low RPM range. We considered other brand products to make it thinner, but since there is no large difference in price, we purchased Mikuni OEM product for peace of mind. We are using the following products:Otani SP2, Ram Air filter oil, no Striker Baffle, and OthersOEMSpec. I think it could be a little smaller. View detail
YOSHIMURABrand! MikuniOEM Product of course!
Some AfterMarket products are similar to OEM Products 。
Not all of them are low quality, but setting parts like Jet are required to be less than Comma accuracy.
YOSHIMURABrand uses MikuniOEM, so it goes without saying. 。
The price is naturally higher than the Other Brand Product (or is the Other Brand Product too cheap?), but you will not have to spend a lot of money later on because you are not sure about setting up the product. ). You don't have to spend a lot of money later on because you are not sure about the settings.
View detail
Pilot Jet Replacement
I bought a Motorcycle that had been replaced by a TMR, and when I switched to this one, it didn't have the same low speed and didn't have the same engine.
Response is better and looks better!
View detail
Used in DR250R
I used it on my SEA BASS DR250R
The 90's MODEL of the DR250R had a forced-release Carburetor instead of a negative pressure system They are employed
The TM28SS is a forced open/close carburetor, but there is little information on the jets, so we have to look into it I turned around and finally found it
The main jet is the general Mikuni Large (or is it?) But the Pilot Jet is a bit special
Some people said it was the same as TMR, but when I actually bought it, it was slightly different
Specifically, the Pilot Jet has a different outside diameter below where the screw is cut
The TM28SS is thinner than the TMR
Screw diameter and Pitch are the same, so it's even more confusing to get about 4 rounds in It has become
If you tighten it any further, the tip of the Pilot Jet becomes a carburetor body It won't go in by hitting the
If you force yourself to tighten the tip of the Pilot Jet or Screw, you can get the tip of the Pilot Jet or Screw You'll be crushed...I'll have to cry when Carburetor body is gone lol
That said, the actual Pilot Jet available was this Jet for HSR
I wasn't familiar with HSR, the Carburetor, but Harley- Davidson's XLXL1200C SPORTSTER 1200Family It seems to be one of the most commonly used in Custom
I don't have a lot of information about this carburetor, although it should be MAJOR in your area
Well, if it's MAJOR, it's not likely to be discontinued immediately or something like that I think it's a good idea to buy it after it becomes
By the way, the TM28 (unbranded) and TM28SS used in Yamaha's 2Cycle are not the same thing So please be careful
View detail
It's a Mikuni OEM Product, so it's not a problem
Buy Mikuni OEM Products rather than buying from Mikuni Buying from YOSHIMURA was a little less than 10%, but I got more points from them It was a great deal View detail
I use the TMR-MJN32 installed on CB400 VTEC 3, Buy Jet Pilot has a high precision, tuned is very sensitive and practical. Very sensitive, maybe it is the relationship of multi-cylinder vehicles, Taiwanese products are completely incomparable.
I use the TMR-MJN32 installed on CB400 VTEC 3, Buy Jet Pilot has a high precision, tuned is very sensitive and practical. Very sensitive, maybe it is the relationship of multi-cylinder vehicles, Taiwanese products are completely incomparable. View detail
It is during a Setting of YOSHIMURA TMR-MJN 38.Since the eyes' smarting from exhaust gas at the time of an Idling and the Plug were deep-black, it shook one-rank thinness.Since air temperature also falls although it is still somewhat deep touch, it is a s
It is during a Setting of YOSHIMURA TMR-MJN 38.Since the eyes' smarting from exhaust gas at the time of an Idling and the Plug were deep-black, it shook one-rank thinness.Since air temperature also falls although it is still somewhat deep touch, it is a standby now. View detail
[Webike Monitor] It was used for TMR-MJN with which ZRX1200 was equipped. I think whether since it is YOSHIMURA Brando who made MJN, it is reliable. Since this one was cheaper at the real sale of the same thing, it chose nominal cost from th
[Webike Monitor] It was used for TMR-MJN with which
ZRX1200 was equipped.
I think whether since it is YOSHIMURA Brando who made
MJN, it is reliable.
Since this one was cheaper at the real sale of the same thing, it chose nominal cost from the goods of a Manufacturer besides
.
View detail