Reviews
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Attached Screw
The idea is a great product.
The included Screw and Spacer 8mm may not be able to be installed if the Motorcycle side is thick.
We purchased another product (see photo) for NumberSecurity, and applied a 6M×diameter 18mm×thickness 3mm Spacer, and adjusted the height of this product so that it does not hit the Number Limit.
*Motorcycle is SMART DIOZ4 2004
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Bolt and color included!
Honestly, it's rather expensive, but the Bolt and color of Aluminum, not cheap iron.
I'm glad that it comes with a moped because I change mopeds around a lot.
Sticker can be directly attached to another motorcycle when transferring liability insurance.
I'm glad to see that it's a great product. It looks good, it's practical, and it's a RECOMMENDATION!
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
If you want to put CALI Sticker! Here it is!
It is a CALI Sticker sticker sticking Plate exclusively for mopeds.
I did not want to put the CALI Sticker directly on the License Plate, so I purchased a Plate.
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Stable KITACO products!
It is a liability insurance Sticker sticker Plate for up to two types of mopeds!
I didn't want to put it directly on the License Plate, so this works perfectly!
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
It's a small component, but it's great.
[How is it used?
I installed it on a JC92 Grom for CALI renewal Timing.
We wanted to keep the color scheme in Black, so we did not use the supplied low-head Bolt and color.
It was installed using DAYTONA's License Plate Bolt and Posh's aluminum spacer. (super self-satisfaction)
Was the one you received as per Image?
The texture and large size are just like the Image, and the packaging was very well done, just like KITACO.
How was your experience with it?
it's the best (Lol)
I had been forced to paste it on a small license plate of a moped.
CALI Sticker now has a proper place in CALI Sticker.
[Points to note]
None in particular, easy to install and position.
I think it is good enough to be ManufacturerStandard Equipment.
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
SmallerParts, but good Accent.
I use it on my MONKEY125.
If you try to put CALI Seal so that the letters are not hidden, it will be easy to peel off the edge of the screen, but this product can be put on a flat surface, so you can put it firmly.
It's a small party, but I think it's a good accent with Black in the Number of Pink.
The product itself is Large strange and beautifully finished, and the Spacer is included, so I am satisfied that it does not wobble after installation.
The Bolt that comes with the product when you get the Number can be easily removed with the +Driver, but this product comes with a Type Bolt that is tightened with a hexagon, so it helps prevent tampering & it is also good in that it looks SMART.
Due to its structure, it will rotate when a little force is applied by hand, but it will not rotate due to the vibration of the Engine.
The price is a little high, but I think it is a product with a high level of satisfaction after installation.
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
It's subtle.
I put it on because I don't like the interference between Sticker and Bolt.
It's not very good because it comes out from the width of the License Plate.
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Is it a bit high?
Is it a bit high? I think it's a good idea, but it's called the Large size, which is just one size larger than the CALI Sticker I bought it after hearing about the
As for the motivation for the purchase, I renewed my CALI the other day, but when I peeled off the sticker, the Number Some of the paint came off with the sticker still on it
Therefore, I wanted to replace the Number and scrapped the car & rarr;registration I bought a plate because I didn't want it to happen again It was a new license plate with half a year of registration I think it's a rare case that the paint peels off and it doesn't hit even if you search the net (sighs)
I'm glad I put it on and it looks cooler than I thought it would, without the worries mentioned above
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Casual and Stylish Parts
What made you decide to buy?
The CALI Sticker that is stuck in Space at the top of the License PlateLeft One thing I wanted to do was to keep the Number and CALI Sticker separate, and the other, from behind, casually I wanted a stylish look that wasn't there, so I bought and installed it
By the way... I bought the KN Project's Cali Sticker Plate in August of '19 and My CALI renewal was for April 20, so I kept it until I renewed it The CALI Sticker Plate for the KN project this month, the month of renewal, and the CALI that was just renewed I put Sticker on it... and by golly, the Plate is better than the CALI Sticker Large size, I felt quite uncomfortable (tears), I checked the size, CALI Sticker size is 3.5×3.5 KN Planning's Cali Sticker PlateSize is 4.5×4.6 CALI Because the feeling of discomfort after Sticker attachment could not be wiped out, KITACOCali I changed to Sticker Plate By the way, the KN Project's Cali Sticker Plate has become a Key Holder!
How was your experience with it?
KITACOCali Sticker PlateSize is 4.0×4.0 CALI Sticker size is 3.5×3.5 KN Planning's Cali Sticker It sits on the plate more neatly than the plate Also, because the plate is flat, it can be applied more neatly than the number
Was the installation difficult?
The Plate itself can be installed with Hexagonal Wrench and 10? Easy to install The difficulty in this process was that the newly updated CALI Sticker was installed in the KN project This was the process of stripping it off the Cali Sticker Plate To remove the Cali Sticker cleanly, put boiling water and mild detergent in a container and When the Sticker Plate is warmed up, the adhesive strength weakens and the Sticker Plate becomes neutral again The detergent will make it easier to remove, but be careful not to work too fast or forcibly It is Also, since hot water is used, be careful of the burn Keep quiet until we get back I left it quietly for one night In addition, the transplantation work is self-responsibility, and please consider it to be a reference
【Please tell me the installation point and hang】
The Plate itself can be installed with Hexagonal Wrench and 10? It is easy to install, but you can install the NumberMounting Bolt in one place at a time Installation! By doing so, the Number is fixed and both hands can be used to work without stress By doing so, the Number is fixed, both hands can be used and the work can proceed without stress After installing it, please check it from behind You may notice things from a distance that you may not notice up close
[Others]
I think the price is not cheap at $1,600 including tax I was put off in purchasing one myself, but now I'm glad I did! I think The gloom from the rear has become stylish Also, when you buy a Sticker Plate, it's easy to put Sticker on your car when you renew your liability insurance I think it would be nice to put it up nicely in
If the liability sticker position is 250? or less, the upper portion of the License PlateLeft and the road It is required by the Motor Vehicles Act and also note where the word Number is hidden
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Required in some areas
I'm not sure about all prefectures, but the PinkNumber in our area has the upper part of Yamagata When you install the seal, you have to cut the seal to make it stick
So this bracket looks great and installs beautifully!
Number is recommended for those in the Yamagata area
I purchased the pink color, but there was no particular feeling of discomfort with the Number
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Maybe the original?
This came out and saved me from getting dirty in Number At that time, there was only KITACO, but now it is good to be able to choose from a variety of companies View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Satisfied except that Cover just touches it
As expected, when you remove Motorcycle Cover it is slightly misplaced just by touching Cover somewhat MinusPoint.
But I wonder if it can not be helped structurally.
Together with the License Frame, the sense of fashion around Number will be much more increased!
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
Good texture
I purchased Pink according to the color of Number.
Although it is a color, the product photo is the same as the color of Number, but the real thing is glossy and slightly different.
But since the large portion is hidden in Seal and the difference is not conspicuous so well it is okay.
The thing itself is Large funny good.
However, since the height of the attached Color is 8 mm, it comes to a considerable extent.
So I am installing two 1 mm Rubber Collar on hand.
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
[Webike Monitor] Although it is an object for compulsory-automobile-liability-insurance Stickers, it can use also as a MINIStay of small digital equipment. The focus of this Items is wonderful. However, when this is stolen,
[Webike Monitor] Although it is an object for
compulsory-automobile-liability-insurance Stickers, it can use also as a MINIStay of small digital equipment.
The focus of this Items is wonderful.
However, when this is stolen, it is brought the whole compulsory-automobile-liability-insurance Sticker.
View detail
Fits: Others Engine Displacement Volume 125cc or less (Moped 1st/2nd Class)
It is ZOOMER. Since it changed into the minicar from motorized registration, it turned out that a Number is changed. It thought that adhesive power would fall if a Seal is removed repeatedly, and purchased. Since it was pleasing also in Design, it
It is ZOOMER.
Since it changed into the minicar from motorized registration, it turned out that a Number is changed.
It thought that adhesive power would fall if a Seal is removed repeatedly, and purchased.
Since it was pleasing also in
Design, it is very satisfactory.
It is said that it is very pleasing and purchases when it is shown to the
friend.
View detail