Reviews
CRF250L MD47 for ACCWiring extraction
Used on a 2023 CRF250L.
If you remove the Left Side Cover, you can access the upper area of the Accessory Case, where there is a 4-pin Optional Connector hidden by the Waterproof Cover. There is a 4P Optional connector hidden by the waterproof cover.:Since 2pc is ACC, we used this Connector to take out ACC and used it for ACC connection of DAYTONAD-UNIT.
View detail
For rainy day measures.
I bought this Coupler because the original Coupler was not waterproof specification. It's a bit large, but I think it's safe for rainy days...? View detail
Sufficient performance
Accuracy is good, and the Bullet Terminal snaps into place in a small, spontaneous way.
The Rubber seal is of good quality and still holds up well about two years after installation.
If I ever get the chance to use it again, I will choose this one.
View detail
LEDCustomTail Lamp To install it !!!
WEBIC mode : I bought LED custom tail light smoke for installation on Grom. WEBIC mode : LED custom tail light coupler connected to smoke is different from grom genuine shape, if you examine it : Coupler housing was waterproof type 3 poles HM 090. I think that it takes less than 10 minutes if you are working on wiring. Just to be careful ? ? ? Pay attention to the direction of the waterproof packing attached to each wiring. Because there is no manual also attached here, Google Mr. resorted to Mr.. Another one is a one-shot game because there is no terminal reserve. If it fails and the terminal is damaged, the terminal for HM 090 comes out to Yahoo auction so please rest assured. Also in my experience, as a certain case record ? ? ? When wiring was connected to the terminal and connected to the coupler, only the terminal remained in the coupler, and the connection was disconnected!. Terminals can be removed from the coupler even at such times. Removal tool minus precision screwdriver (Very small size) is. Although a bit of knack is necessary, you can remove the failed terminal from the coupler, so please do not give up! Connection ? Experience and correct tool selection are necessary for terminal crimping. Perhaps tools are also available for purchase at Webbec, so why buy them at the same time? View detail
Just in case...
I do not think it is necessary because it does not ride when it is basic rain, but sudden rain and car wash etc. In mind when considering when Motorcycle gets wet. It looks like insurance.
Used for Power Sub Harness of Y's Gear.
View detail
OptionCoupler
By installing ETC, you can install it without damaging the OEM's Wiring. Basically I do not like interrupting OEMWiring and connecting it. I had a hard time finding out. View detail
Where Waterproof performance is required
【What made you decide the purchase?】
I was looking for Waterproof Coupler for Automatic for Vehicle where I was using it for use.
【How was it actually used?】
It was as expected as it was also used for each car OEMHarness.
[Others]
I think Mark probably matched the Coupler, so probably it was manufactured by Mr. Sumitomo Electric.
Since there was Catalogue from Mr. Sumitomo Electric, as a reference.
HMWaterproofSeries
Applicable wire Size : 0. 3~1. 25mm2
Applicable wire finished outer diameter : 1. 8~2. 9mm
Applicable wire example (mm 2 / sq) :
AV 0. 5~1. 25
AVS 0. 3~1. 25
AVX 0. 5~1. 25
AVSS 0. 85~1. 25
AVSSX 0. 85~1. 25
* Terminal itself is 1. 4~2. It corresponds to 9 mm, but since WireSeal does not correspond, 1. I write as 8mm ~.
View detail
[Webike Monitor] When the Meter made from a yell Well ACE-2802 was attached to a D tiger, it was used for wiring processing for using a pure Speed sensor. Having used it is not using the Coupler only with a terminal. The triangular type wat
[Webike Monitor] When the Meter made from a yell Well ACE-2802 was attached to a
D tiger, it was used for wiring processing for using a pure Speed sensor.
Having used it is not using the Coupler only with a terminal.
The triangular type water proof Coupler of the
photograph was also fitted satisfactorily.
The pliability of the
Seal is high and it expects waterproof performance.
If [ if the
price is / the back / somewhat cheap ] - ^^
View detail
When a Tail light was exchanged for an external article, the Fender back side was wired with the plug terminal. it decided , however not to arrange, unless it ties checking the combination of a plug whenever it removes, but to exchange for a Coupler,
When a Tail light was exchanged for an external article, the Fender back side was wired with the plug terminal.
it decided
, however not to arrange, unless it ties checking the combination of a plug whenever it removes, but to exchange for a Coupler, since it was troublesome, and since it was a place which receives splashes of mud etc., it ranked next and was alike and exchanged for the water proof Type.
Since it must caulk simultaneously with a Seal when caulking, a hang may be necessity a little.
The degree of satisfaction after the
Seal stuck seriously, has played the role and finishes constructing wiring is quite high ^^
View detail