Reviews
KIJIMAGrip sch RingTube
Grip heater protection and electronic Throttle is heavy so I wanted to make the Grip thicker.
The length and thickness are just right.
View detail
Grip reinforcement is satisfactory
There are no problems with quality, texture, etc.
Design would like to see more Variation.
Well, it's ShrinkTube, so I guess it can't be helped.
View detail
Grip heater protection essentials
Repurchased due to Motorcycle changeover.
Previously used on BMW F800R.
I drove it about 25,000 km in about 7 years,
Installed and never replaced,
They protected Grip.
Grip heater is when the Grip wears out,
exchange.
It would be quite an expense,
It is safe to wear Tube as soon as you purchase Motorcycle.
View detail
Use.
It is easy to grip and feels gentle in the palm of the hand. View detail
comfortable to hold
It seems to be less stressful on the palm of the hand than holding the Grip directly. (This is my personal impression). View detail
Decrease measures?
The BMW Motorcycle grips seem to wear off a little faster, so I installed them as a countermeasure.
I am satisfied.
View detail
ErgoWorks (KIJIMA) Grip Shrink Tube
I was told that S1000RR's grip is with heater, so when it wears out, the whole part needs to be replaced (50,000 yen including labor! I was told that I would need to replace the whole part when it wears out (50,000 yen including labor!), so I installed it. View detail
Grip Reinforcement
Just put it through the Grip and heat it up with the Heat gun.
It's easy. bmw has a grip heater, so I recommend installing it as soon as possible because replacing the grips will be expensive.:1 Set of 2pcs. but the length is slightly different, so if you are concerned about the length, please adjust the length with Scissors.
View detail
Texture very good
The price is good, the texture is good, and it is easy to grip and protect.
Installation is also easy with a heat gun.
View detail
regularly-scheduled replacement parts
2 years use
As expected, only the Throttle side was worn out and felt a decrease in gripping force, so it was replaced.
Just cut, fit, and sear with a Heat gun.
It is cosmetically superior because it can easily protect OEM's expensive Grip heater from abrasion.
And it lasted two years.
View detail
I'll take your opinions into consideration.
I had it installed when I took delivery of my car.
The grips wear pretty well."
It would cost a nice Gold amount to replace it."
I thought it would be a good idea to install it before I fell down.
I'm not sure how the Grip felt before it was installed.
Maybe a little poncy after installation.
I am riding it without any discomfort.
Installation was requested by Dealer upon delivery of the car.
Perhaps it is easy.
I think I will do it myself when it wears out and needs to be replaced.
View detail
I installed it on my s1000rr.
I installed it on my s1000rr.
I have been concerned about Grip wear lately and knew about this product, but had put off purchasing it.
The grip, texture, etc. were both great.
View detail
Grip wear prevention.
I purchased the Grip heater because it is more worn than I expected.
The Grip heater used is PLOT's EFFEXGrip heater.
There is also a product for EFFEX in Lineup, but I preferred the look of this one, so I used this product this time.
I was worried about whether it would stick properly because it is quite uneven, but it worked perfectly!
After covering it, the whole thing was then burned with a heat gun.
It may be a little easy to Slip because of its spongy feel.
It is simply a Large Heat Shrink Tube.
I didn't know such a product existed, and if I had known, I would have installed it before it wore out.
View detail
Used to prevent slipping
My HondaOEM Sports GripHeater started to slip after about a year of being installed.
This product is attached from above.
It was very effective in terms of preventing slipping, and I didn't have to grip the Grip as hard.
It made the ride very easy.
Heat Shrink Tube in the same manner as the Heat Shrink Tube, aligning and warming it with a Dryer (preferably a Heat gun) will cause it to shrink.
It is a small point, but since it is attached to the original grips, the grips are larger in diameter, so it is necessary to use a larger grips.
The feel of the grip changes considerably.
The Sports GripHeater is sold on the slenderness of its grips.
When I rolled this one up, it was about as thick as a regular Grip heater.
The non-slip effect remains the same even after a year, and if you don't like it, you can cut it off and remove it immediately.
You can also try it easily.
(If you want to increase the non-slip effect/grip diameter (but don't want to change the grips for some reason), you can use the
Very effective product.
View detail
Cosmo
With a heat gun, it takes less than 5 minutes to install, and you only need a heat gun for installation, but the only thing left is durability. View detail
It's easier than you think!
Bought this to prevent grip wear on my S1000R OEMGrip heater.
Because I had seen the installation article of other people beforehand, I bought Heat gun together and installed it immediately.
Very easy to install, just run it through the Grip and warm it up.
The hang is to apply the warm air of the Heat gun evenly, and it is completed in about two or three minutes of One Side.
The surface seems a little smooth, but if the Gloves are leather, they don't slip, especially
It is available.
If I have one complaint, it's that the price is a little low, as others have commented.
Well, it's a small price to pay for replacing the OEM Grip.
View detail
This is a must have item for BMW riders.
I installed it on my BMW R nineT.
To replace the Grip on a BMW, you have to replace the entire Throttle lever.
However, wear of the Grip is inevitable. (Leather Gloves can slow down the wear to some extent) 。
About the size feeling
The length is perfectly aligned with Lever in the shipping stage. Therefore, the position was easy to align.
I used a heat gun to attach it, but it didn't need to be that hot for it to shrink. (HIGH) But I had a feeling it would shrink. (I don't know.) 。
As for the pattern and grip feeling, I personally feel that it is neither good nor bad. As for the price, it is acceptable.
View detail
Grip heater Grip wear and tear measures
I bought this for the Grip heater to prevent Grip wear.
I use them on my BMW S1000RR, and since they are OEM grips with a built-in heater, when the grips are worn out, you have to replace the entire grip unit. Therefore, it is very different from changing to an external grip for 4,000 to 5,000 yen. To install the Grip Unit, use the heat gun to shrink it. When it becomes loose, heat up the heat gun and shrink it again.:Since it is Rubber, it does not compromise the performance of the Grip Parts.
View detail
It can be mounted with a grip heater and is extremely thick.
Grip heater became slippery, so I installed it to prevent it from slipping.
As a result, Grip is good.
But I put it on the Grip heater, which is originally thick, so it became very thick.
And I chose red, which makes it look even thicker.
I immediately bought the Black one again.
It's very easy to install the thing because all you have to do is cover it up and stir it up.
But I didn't have a Heat gun, so I bought one for this.
If you don't have the right tools, you can't attach them, so it's not very cosmetic.
View detail
I think it's good Items
I've been reading the articles on the introduction of motorcycles, etc., and it seems that people are using them I also tried to put it on
I installed it myself, but I'm not sure if the Left Side wasn't overheated enough, or if the Grip Heater As I used to use it, it came off
I overheat it again and use it
It's working fine now, I didn't have it on my last motorcycle, so it's 10,000 The grip is decreasing in Km, but this time, it seems to be Large sturdy
View detail