PAGE TOP
Keyword:
Model Search:
  • Register MyBike
Search Criteria:
  • Product: Slant License Plate Bracket

Product: Slant License Plate Bracket

    I thought about installing it on Fender Eliminator on another vehicle but I could not install it without clearance with License Plate Light


    Put this item to cut the Rear Fender of Address and angle it to a near vertical number.
    Is it because the vibration is Large in Single? Another Fender Eliminator is a strong Type that also fixes SIDE and more than double the price. Is that necessary?
    Certainly, when running after installing, the number is fluttered, but if you prevent vibration from breaking out Number, you can either add Cushion between Number and Bracket or attach License Plate Holder
    Is it okay.
    There is no extra Bracket next to it, so I'm satisfied as I'm refreshing.

    Put this item to cut the Rear Fender of Address and angle it to a near vertical number.
    Is it because the vibration is Large in Single? Another Fender Eliminator is a strong Type that also fixes SIDE and more than double the price. Is that necessary?
    Certainly, when running after installing, the number is fluttered, but if you prevent vibration from breaking out Number, you can either add Cushion between Number and Bracket or attach License Plate Holder
    Is it okay.
    There is no extra Bracket next to it, so I'm satisfied as I'm refreshing.

    It is attached to the original maker Scooter but it is not warped and it has become a very good angle. Normally it is hard to see NORMAL. Although the finish is slightly sloppy but it is a part that can not be seen, there is no particular problem.

    It is attached to the original maker Scooter but it is not warped and it has become a very good angle. Normally it is hard to see NORMAL. Although the finish is slightly sloppy but it is a part that can not be seen, there is no particular problem.

    【What made you decide the purchase?】
    It is decided that the comment of Impression and the height of evaluation
    【How was it actually used?】
    Certainly cheap and poor products are different in one taste and lid taste.
    【Was it difficult to install? (Hard parts case)】
    It was relatively simple as it removes the existing Number and tightens it together. Also handling Instruction Manual is described carefully so it is wonderful.
    【Please tell me the point of installation and hang (in the case of Hard parts)】
    Do not over tighten Bolt kind, make sure that there is no loose after running.
    [Is there anything I was disappointed about?]
    This product is TAB screw at both ends, so you can install Nuts if you have one. In other words, since Ploy itself has Screw Mountain on both ends, it can not be used with PlateSingle Body.
    【Hope for Manufacturer - Please let me know if you have any improvement points]
    I thought I wanted not to weld Screw Mountain.
    【Have you compared items?】
    License Plate Holder of POSH and so-called pushing raising
    [Others]
    I am using this product for reverse installation, because it is changing to POSH's Fender Eliminator Kit, the angle of Number is slightly rising so it was a little bit so it is for lowering the angle, please refer to the image. m (__) m

    【What made you decide the purchase?】
    It is decided that the comment of Impression and the height of evaluation
    【How was it actually used?】
    Certainly cheap and poor products are different in one taste and lid taste.
    【Was it difficult to install? (Hard parts case)】
    It was relatively simple as it removes the existing Number and tightens it together. Also handling Instruction Manual is described carefully so it is wonderful.
    【Please tell me the point of installation and hang (in the case of Hard parts)】
    Do not over tighten Bolt kind, make sure that there is no loose after running.
    [Is there anything I was disappointed about?]
    This product is TAB screw at both ends, so you can install Nuts if you have one. In other words, since Ploy itself has Screw Mountain on both ends, it can not be used with PlateSingle Body.
    【Hope for Manufacturer - Please let me know if you have any improvement points]
    I thought I wanted not to weld Screw Mountain.
    【Have you compared items?】
    License Plate Holder of POSH and so-called pushing raising
    [Others]
    I am using this product for reverse installation, because it is changing to POSH's Fender Eliminator Kit, the angle of Number is slightly rising so it was a little bit so it is for lowering the angle, please refer to the image. m (__) m

    It is good to make it cheap and secure.
    As the Number was moved to the back of the Backrest, due to Number which became too vertical mounting, the angle was adjusted with this product.

    It is good to make it cheap and secure.
    As the Number was moved to the back of the Backrest, due to Number which became too vertical mounting, the angle was adjusted with this product.

    【What made you decide the purchase?】 Since the Fender EliminatorSet is not in CBR 250 RR, since I tried to cut OEMFender by myself and turn it into my own Fender Eliminator, since the angle of Number is overturned, I will sell Universal Bracket sold at home center and so on so that it is level with the Tail part of Seat Cowl Although I was thinking to use it by bending it seems weak, friends broke Bracket while traveling in that way Bracket broke and dropped Number So when I was looking for a strong Bracket I found DAYTONA 's Slant License Bracket so I bought it Saw.

    【How was it actually used?】 I was worried how much the angle would rise, but I felt it was just too crowded, because it faced the tail cowl just in line with the angle of the original Fender, it's a very nice feeling. Unlike the Universal Bracket of the Home center, it's solid, so it's a bit heavy but it's sturdy and it does not seem to worry about breaking.

    【Was it difficult to install? (Hard parts case)】 Bracket itself is easy because it is attached immediately without processing anything.

    【Please tell me the point of installation and hang (in the case of Hard parts)】 It's very simple, so it's not particularly.

    [Is there anything I was disappointed about?] I wanted to decorate Number Bolt to Bolt, but I am sorry just because I can only use the Bolt included.

    【Hope for Manufacturer - Please tell me if there are any improvement points】 I'm happy if you can use decorative Bolt as I wrote above.

    【Have you compared items?】 Home center's Universal Bracket
    [Others] Although I was worried because there were few corresponding models, I could use it without problems for CBR 250 RR.