Reviews
Fits: HONDA CR250R, HONDA CR125R, HONDA CRF250R, HONDA CRF450R, HONDA CRF450RX, HUSQVARNA FC250, HUSQVARNA FC250, HUSQVARNA FC350, HUSQVARNA FC350, HUSQVARNA FC450, HUSQVARNA FC450, HUSQVARNA FE125-501, HUSQVARNA FX350, HUSQVARNA FX450, HUSQVARNA TC125, HUSQVARNA TC125, HUSQVARNA TC250, HUSQVARNA TC250, HUSQVARNA TE125-501, HUSQVARNA TX125
Convenient and lightweight! But low strength
Large change is useful for washing the underside of the Motocrosser!
However, it is so strong that it will bend if you try to start KICK with STAND applied.
If it only supports the weight of the car, there is no problem.
The handlebar can be used as an insert, making it easy to insert into an Axle Shaft.
View detail
L and U-shaped Attachment is Quantity:Great value for the set!
[How is it used?
I used to use a cheap Rear stand, but I am replacing it with a new one, and since I have several vehicles, both the L and U-shaped ones are available.:I was looking for something that could handle multiple vehicles with Set.
I would have preferred JTrip's, but they are quite expensive, so I chose this product.
Was the one you received as per Image?
The texture is not the best and a little cheap, but I think it is well worth the price.
It was also much lighter than the No Brand STAND we had been using, making it much easier to use.
The assembly is almost complete when it arrives, so all you have to do is adjust the height and tighten the screws.
How was your experience with it?
The body is light and the roller movement is smooth and light.
Usability is normal, but I am glad that it is lightweight, making it easier to maneuver within Garage.
[Points to note]
Hook is somewhat cheap.
If you are concerned about it, JTrip is a better choice. There is a price difference, so please consult with your Wallet.
Also, you need to bother with tools when adjusting the height, so that is MinusPoint.
How did it compare to other products?
It is easier to use than STAND, the No Brand product I had been using.
【Review】
This Rear stand is light and normally easy to use.
Not the best, but considering the price, I think it was worth more than the price.
View detail
Fits: その他 TOYOTA Hiace DX, その他 TOYOTA Hiace DX
It's well made, but....
Installed on High ace3 late model, WideMiddle roof car.
It looks and feels solid, but I can't get the Hook to work.
I had no choice but to use Tie Down's Sub belt.
View detail
Plenty of capacity! You can use it for the foreseeable future.
DAYTONA's Wire twister and Quantity:I bought it as a set
The product is of good quality, gives a beautiful finish, comes in a container, and is easy to use.
In addition, the generous capacity ensures that there is no need to worry about failure.
View detail
Individual differences?
I don't know how it works in other vehicles.
Maybe it's an individual difference.
The lower part of the Fuel Cock interferes with the Engine.
Float the rear of the tank with Washeretc.
I installed it anyway.
Seat is now difficult to install.
Fuel Hose fitting is thinner than OEM
The original Hose is not available.
View detail
Used for RM125
I use it to Lift up my RM125.
I thought that the Rail type would be too tight for the Racer's ride height, so I decided to go with this one.
Surprisingly, however, the height was just a little above the lower limit of the adjustment range and just below the belly.
It seemed that even the Girito Rail type could be lifted up.
View detail
For forest road
We chose it for Puncture repair on forest roads.
Lightweight Compact is good.
View detail
Easy Lift up
I had a hard time deciding between this and Jack's, but I chose this one because of its light weight.
Narrow type STAND is a little unstable, but it is stable when lifting the front.
When lifting both wheels or only the rear wheel, it is recommended to fix the Front with chocks.
This was the right choice for ease of lift up and portability.
View detail
How about one for Garage?
I purchased this product for the first time for Chain Maintenance.
I was nervous when I put it up for the first time, but Quantity was there without a hitch!:Set is ready.
It is so convenient that I wish I had introduced it sooner.
I am satisfied with the quality of the product, but I have one point,
The hook part was bare gold and it looked like it might scratch the Swing Arm,
I covered it with Fuel Hose, which happened to be available.
Other companies' MAJOR products have already taken countermeasures in this area, so please check this when purchasing.
View detail
Convenient
A particular problem when washing Boots is when washing the reverse side, which can be difficult if done in a half-assed manner, as water can get inside.
But this is good.
Water does not come in upside down and can be fixed so it can be scrubbed with Brush.
This product is very useful, especially off-road, where dirt gets all over the place.
However, there is one drawback... Water can get into the cavity of the Pipe through the screw gap.
Muddy or rusty water comes out of the crevice of the Screw when held at different angles.
This should not be a problem if you drain the water frequently, but be aware that if you hold it without knowing it, your clothes may get dirty.
View detail
Rugged STAND
It is BoxSTAND, Off-road motorcycle owners should have at least one.
I think it would be easier to put the Block under the Side Stand, tilt it to Left, and then put it in from the body Right.
BoxSTAND is so sturdy that once you buy one, it will last you a lifetime.
View detail
For transporter use with light trucks
It can be a Ladder and it can be an Extender.
It is strong and looks good, so I am generally satisfied.
I use it with mxSTAND to load and unload Motorcycle.
View detail
Unit Unit Silencer plug rating
4ST's Exhaust System has a thin end with a Silencer fixing Screw and a release bet.
I used to shave and modify it, but this Plug is not a good choice for me.
Exactly.
View detail
A little processing was required.
The inner diameter of the Adapter seemed to be a little small, so I could not install it, and since I did not want to cut down the STANDBODY side, I used a Leutor to cut down the inner diameter of the Adapter I purchased this time so that it would be large enough to fit. Although I was disappointed with the product itself, I am glad that the Adapter only was sold, even if it requires a little modification, because without it, I could not STAND-UP safely. View detail
Needs a little work.
The inner diameter of the Adapter seemed to be a little small, so I could not install it, and since I did not want to cut down the STANDBODY side, I used a Leutor to cut down the inner diameter of the Adapter I purchased this time so that it would be large enough to fit. Although I was disappointed with the product itself, I am glad that the Adapter only was sold, even if it requires a little modification, because without it, I could not STAND-UP safely. View detail
easy
I bought this for the purpose of applying ChainGrease and polishing the wheels, and it works well considering the price, although it does require a bit of effort to rotate the Tire. View detail
This is a great front stand.
This is a great stand for the price.
This is my first time using a front stand. It wasn't difficult to use.
After inserting the adapter that fits your bike into the front hook, hook it on your bike and lift it up.
It's quite sturdy and supports the bike well.
However, care must be taken not to scratch the front fender when using it.
I used it for gsx r1000 and there was no problem using it.
I highly recommend it to others as well. -------------------------------------------------- -------- It is a great stand for the price. I'm the first to use the front stand. It was not difficult to use. Put the adapter that fits the bike in the front ring and put it on the bike. It is quite strong and supports the bike. However, you should be careful not to scratch the front fender when using it. I used it for the GSX R1000, but there was no problem. It is highly recommended for others. Powered by Google Translator
View detail
Unit B2510 front stem-up stand
Tried it on a 2006 cbr600rr. There's no interference with the cowl, but you can't mount it the way you want unless you remove the horn. It interferes with wheel extraction, but try adjusting the height. View detail
Scooter Engine unloading is easy and safe.
I bought this to unload the Engine on my Scooter.
Front tire is fixed with steady STAND and rear frame is hung with 100kgClass Small Type Chain block.
The rigidity is high enough, and there are no problems at all. The construction and precision are high, and the bolt holes are perfectly aligned with the floor.:Pair (for Left and Right) The right angle of the legs of the "Rear" is also out and there is no tilt or rattling of the legs. The weight is not a problem for transportation, but in my case, I have to assemble and disassemble it each time due to the space in Garage, so I am a little concerned about the weight.:Pair (for Left and Right) It would be nice to be able to install the Hook on the
View detail
A little high for Minimoto use.
I was wondering about the step up Type,
Foldable and light enough to be left in the car.
I bought this one so that I can
The height is a bit high for Minimoto use.
Lifting and placing the Motorcycle is quite Large and strange.
You have to lift it up tight when you put it on.
The non-slip Rubber bites into the Under Guard.
STAND is running away from us.
If the leg opening angle can be changed and the height can be altered.
I thought it was nice.
By the way, Rubber smelled like petroleum at first.
After a week or so, it stopped bothering me.
View detail