Reviews
Thank God they don't sell them at the homestore.
When I installed NAMETALCraft's aluminum chain guard on Over Racing's Swing Arm, the bolt nut on the reverse side was dangerous because it interfered with the chain when I fixed it with the bolt on the front side bracket. I inserted a 12mm Truss Screw from the Reverse side and fixed it with this Cap Nut with Flange from the outside using an AngleDriver. After that, there was no more interference and I am satisfied with the result.
This was helpful because these special Nuts are not sold in Home center.
View detail
Hidden Dress-upItems!
There are so many little parts to We-Big, and it's fun to research and plan out all the details! KITACO and ConvenienceParts have a wide range of products for motorcycles. There are a lot of screws and plastic parts that can be Isn't this good for dress-up? There are some beautiful Parts that look like this. This time I found this 24K Plating, SUS Cap Nut with Flange! I wasn't sure if I could put it on my car Grom, but I bought it, and even though I bought two bags That's 1,200 yen! Cheap compared to other dress-up parts!
The first aim is to replace the Cap Nut that fixes the exhaust pipe to the cylinder. It was a However, because of the length of the Stud bolt, the Long Type Nut was still used. This Nut made by KITACO seemed to be able to tighten it, but it was too much. Because it was like a Limit, I decided not to turn on the Exhaust System. Since the frequency of removal is quite high, this Nut is getting painful. So I'm looking for a strong and clean nut, but if it's not a Cap Nut, the Stud bolt is not I'm worried that it might rust. But Material:Titanium's and the like are just regular Nut with a popping tip.
On the other hand, this Cap Nut and the perfectly sized Cap Nut from KITACO are used in four It is the head cover of Engine. Before installing it, I cleaned the bolt and installed the head cover. I applied a small amount of MOTOREX CuCompound before tightening it up. It may not be as hot as the pipe part, but I think it still gets quite hot, so bite prevention is essential.
What do you think? It's beautiful! It doesn't match the color of the surrounding gold alumite parts, but this one in 24K Plating Real gold color. I wonder how long this shine will last, but I'm sure it's stronger than Anodized. It may not be able to be used on every car, but you can make this kind of customization with some creativity. It is possible. For the Large size of the effect, it's very cheap! Please visit ConvenienceParts to find a beautiful part that will fit your vehicle! Please!
View detail
Accuracy...
Since OEMCap Nut of Cylinder head came, I bought it for Replacement together with Reinforced Stud Bolt.
1 pc out of 4. The accuracy of the thread of the screw was bad, and the thread of Stud bolt was broken owing to gnawing. Is it inferior to Made in Thailand's OEM Parts and is not JAPAN?
View detail
For the purpose of improving beauty
AGRAS : Screw is heavy to install the Racing slider
Because we used Titanium's long Bolt, it is bag-like so that the Screw part does not protrude for the purpose of preventing danger and improving aesthetic appearance Nut. KITACOConveniencePartsK-CON : I used Cap Nut with Flange.
It also becomes Dress-up
View detail
Since the Screw is exposed by the usual Nut specification in many cases, the old vehicle is ideal for rust prevention of the Screw of such parts.It is GOOD which cannot attach the crack by a tool easily at the time of work, either, since it is the STA
Since the Screw is exposed by the usual Nut specification in many cases, the old vehicle is ideal for rust prevention of the Screw of such parts.It is GOOD which cannot attach the crack by a tool easily at the time of work, either, since it is the
STAINLESS STEEL!
View detail