Reviews
Fits: BMW S1000RR, BMW S1000R, BMW S1000R
Inexpensive among Front Axle Sliders
[How is it used?
Used as Slider in Front section
Was the one you received as per Image?
It is the same as the photo shown in the publication.
Was the installation difficult?
The installation itself is simple, but the Quantity:Pair (for Left and Right) Which of the following is to be installed as Main?
Check the installation. Check the Instruction Manual for handling.
The part that passes through the Axle Shaft is fully threaded,
It has a rubber tube to prevent scratches, but it is obviously long.
Since it was not possible to install it, the tube was cut and shortened a little for use.
How was your experience with it?
Hopefully not used, as it is effective in the event of a fall.
BABYFACE's Axle Protector was selected because of its proven track record and favorable reputation.
Since the fit is not that great, it is good to be able to wear it in a natural way.
The surfaces are just right.
[Included Parts:were they on?
Handling Instruction Manual available.
[Was there anything that disappointed you?
The resin part is grooved, but it is not chamfered, so if you easily grip it and tighten it,
Easily cuts hands. I think it should be chamfered originally because it is very sharp.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I would like the resin part to be chamfered.
View detail
Fits: DUCATI 899Panigale, DUCATI 959Panigale, DUCATI 1199Panigale, DUCATI 1299Panigale, DUCATI DIAVEL, DUCATI StreetFighterV2
Simple and inexpensive.
I thought I had researched and ordered it, but the PanigaleV4S was not among the compatible models. Sweat
Item number:006-AD007
The length of the Long Bolt was sufficient, so we cut the transparent tube of the Long Bolt by 1 cm to match the length.
It can only be installed if you have a 10mm deep socket.
I am surprised that neither the product introduction nor the Review mentions SheepSocket.
I went to Astro to buy one.
Single Item:about ?,300, Quantity:It is about 2500 for a set.
View detail
They'll keep you safe
I've been a customer of Panigale and CBR, so I'm going to use this one again because I trust it Manufacturer The installation is just screwed in, except for using Screw Lock
It will also stop the impact and scratches of standing moss and scratches to the Smallest limit, so only the most expensive Fork people I would recommend these Parts even if you don't have them
View detail
It looks stylish when installed
I doubt it will protect the motorcycle in the event of a fall since it doesn't protrude much, but it looks stylish
I'm not sure I'd be comfortable as a Slider without being a bit more assertive like the other Manufacturers
I don't want her to be stuck with me Be safe ！
View detail
Fits: KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Z1000 (water-cooled)
For you,
I thought that it was due to mitigation at the time of falling as I experienced standing,
Making ? Easy to install and easy to install, it was possible to install in 10 minutes as fast as ten in Socket wrench of 10?.
However, the Instruction Manual is too small and can not be read, Seal in the appendix is ??Large.
View detail
Left is Tsuraichi Right - - - -
In use in MT 07 in 2016
Left as a sample picture Tsuruti
Right - - - - Because there was a gap of 2 - 3 mm and it was a ubiquitous
We responded to Color with Grinder
View detail
I am satisfied.
Shaft was long so we had to process it. Although it can be mounted without processing it, it can be mounted cleanly.
We made this product because of Engine Slurder and Manufacturer, but the feeling of Fit after installation is satisfactory. Slider original role is not yet. I hope nothing will come.
View detail
Fits perfectly onto a Honda CB400SF 2010 perfectly. A simple 24 mm spanner to remove stock bolt and you simply fit the frame sliders and tighten the 22mm bolt, followed by the 2x 10mm lock nuts on each end. Product is great quality and has nice aest
Fits perfectly onto a Honda CB400SF 2010 perfectly. A simple 24 mm spanner to remove stock bolt and you simply fit the frame sliders and tighten the 22mm bolt, followed by the 2x 10mm lock nuts on each end. Product is great quality and has nice aesthetics. View detail
Fits: DUCATI 899Panigale, DUCATI 959Panigale, DUCATI 1199Panigale, DUCATI 1299Panigale, DUCATI DIAVEL, DUCATI StreetFighterV2
Satisfied with Cost performance
I installed it as a point of Front axle
Easy installation Instruction Manual was included but it is hard to understand
With Deer bell compatible items
I tried Fit but I tried it several times with trial and error
Quality is suitable for the price
Where it is not possible or impossible
View detail
Fits: KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Z1000 (water-cooled)
Although necessity was not felt for the time being, it purchased by the Frame slider and a Set.attachment was easy.A feeling of unification can be taken and it is result satisfaction.
Although necessity was not felt for the time being, it purchased by the Frame slider and a Set.
attachment was easy.A feeling of
unification can be taken and it is result satisfaction.
View detail
Fits: KAWASAKI Ninja 1000 (Z1000SX), KAWASAKI Z1000 (water-cooled)
Although it stood and there were no preparations, such as GOKE, if a rainy day and a few are also helpful to mitigation of a car body was thought, and it purchased. Although it was not, since R and a sticker were stuck on the right-hand side of the pa
Although it stood and there were no preparations, such as GOKE, if a rainy day and a few are also helpful to mitigation of a car body was thought, and it purchased.
Although it was not, since R and a sticker were stuck on the right-hand side of the packing bag, it attached and the instruction manual shone without changing between right and left.
Since a screw is a lock screw, it does not loosen.
View detail