Reviews
To protect the license plate.
[How is it used?
I searched for a License Plate Holder on Webike to protect my SEROW225WE License Plate. I was looking for the cheapest product and came across KITACO's product.
How was your experience with it?
The appearance is that of steel with plating, so the Material:If you compare it with the products that are Anodized Treatment for each color in Aluminum. Cheapness." cannot be hidden.
However, the motive for purchasing License Plate protection that bends every time I go out to play in the mountains." Therefore, since they are going to be bent anyway, Cost is more important than texture.
How did it compare to other products?
As I said above. "Cheapish" The price is actually cheap, so there is nothing to be done about it.
Material of the same thickness, perhaps due to the material of steel:It is a little more rigid than the Aluminum product, and so far the License Plate has not bent.
[Points to note]
The product is made of steel with plating treatment, so it will eventually be rusted if scratched.
Even without Wound, Rust may be unavoidable depending on the environment, so it may be better to protect it with Wax or similar.
There is a possibility that you may get hurt if you handle it roughly with your bare hands. [Color] I sprayed ClearSpray.
Other items that would be helpful
The deciding factor in the purchase
Cheapness, that's what it's all about.
In my case. "the expendables" However, if you are looking for texture, Material:Aluminum and Material:I think you will have less post-purchase regret if you consider Carbon's other products.
【Included Parts:presence or absence】.
Only one Plate is available.
Simple, low price, just the right product for me.
[ITEMS TO BUY TOGETHER
The existing Bolt can be used to install the License Plate with no problem, but it may be a good idea to add an Aluminum Collar or CoolBolt (if you are in an area where theft is common, you may want to consider an anti-theft Bolt).
Opinions and requests to Manufacturer.
We look forward to a long-lasting Lineup for Cost-conscious Users.
View detail
The License Plate is bent, so it is reinforced with a License Plate Holder!
I was looking for an inexpensive License Plate Holder before the License Plate bent into a squishy mess, and I found KITACO's License Plate Holder!
I like it because of its simple design and good texture!
View detail
Solidly built
I haven't installed it yet, but I think the texture and look are great.
It seems to be sturdy and does not seem to have any flapping.
View detail
Effective for vibration control of License PlateLarge
Used for KLX125.
Since the License Plate has been cracking due to vibration, I installed it for protection, but it seems to be stronger than aluminum and so far I have had no problems.
I think the quality is good with no unevenness in plating.
View detail
Seeking to hide bracket and increase texture
Purchased to conceal Number mounting Bracket.
It was not completely hidden, but it was better.
The product is not as shiny as I expected.
be on the verge of tying the number Claws. should be spread out and then put Number between them.
I feel like I'm getting a little old-fashioned, but it's cheap. Well, okay." I feel like.
View detail
Is good
It is inexpensive, but the accuracy is good and the quality of the plating is fine. There is no sense of existence than I thought in a good sense after installation. The point that I want to improve only one is to pinch the lower side of Number. Claws. This is the sharp edge. Since this is a sharp edge, it would be 100 points if you could refine it to a chamfered shape, but since it's plating, you can't sand it yourself. (Rusty) So.... View detail
This part is a good one for the cheap
I bought it to protect Number on MONKEY
The Number is already a little warped when the motorcycle is put in and out of the garage In the meantime
Modified and installed
It is a little heavy, but I am satisfied with its cheapness and simplicity
The claw that inserts the bottom of the Number seems to be tight, but if you put a little force, it will go in
But after you plug it in, you can use Quantity:Pair (for Left and Right) The Gap adjustment of the
You may want to plug it in
PlateHolder and Number Quantity:Pair (for Left and Right) I guess I shouldn't care about the difference in the gap between
View detail