Reviews
Easy to change for new adapter.
The built quality is very high quality. Feeling secure and protected Easy to install and easy to use Very durable and feel confident to ride Very cheap than other brand Shipping as expected quick. Easy fix with the old broken adapter. The packaging is wrap with many protection. View detail
I used it for a Handlebar with a thick inner diameter.
I installed it on a HUSQVARNA TE2502017 which I always use for forest road Touring.
When I changed the handlebar to an ISA one, the inner diameter of the handlebar became thicker and the handlebar guard I had been using could no longer be used. I purchased this Adapter and was able to fix the bar end without any problems.
View detail
It flew away somewhere, so...
When he was competing in an off-road race, he fell off somewhere, probably because his Screw got loose in the Shock of the fall.
I bought this Repair item after deciding that this Guard itself is a bit expensive and still usable.
It is not about performance, but it is nice to have repair items for parts that are easily lost or damaged.
View detail
It is necessary for Mast when repairing and removing.
It is very difficult to reuse something that has been removed for Handlebar replacement, etc., if it eventually becomes unusable.
Also, if the Hex part has a governor, replace it as much as possible.
When removing the Quantity:You don't have to worry about anything if you buy from Set.
Especially before entering a race... I get unnecessarily impatient.
I'd appreciate it if you could make it a little harder to turn...
View detail
Repair item
This is an Adapter of Hand guard which can be removed if you gap a little.
It's easy to lose, so it's nice to have it as a repair item, but it's a bit pricey….
Quantity:1 Set of 2pcs. and when you lose it, it's usually one of them, so it's safe to keep the other one in your luggage as a spare.
If the Adapter becomes rickety, it will wobble no matter how hard you tighten it, so regular replacement is also recommended.
View detail
insisting on being a part of
I bought it for the Hand guard installation of the same brand.
It is precise, tight, and firmly fastened.
The mounting bolts are also strong enough to prevent licking even when tightened down.
If this is a product that uses an inferior Bolt, the last thing you want to do is put it on and not remove it.... This is an important point because it can happen.
View detail
Anything
I bought this item.
I arrived at hand, I went mounting without any sense of incompatibility...
That's incongruous.
Bolt is surely a new item was Stainless, is not it? Product images are also stainless... "* The shown image is only for reference. It may differ from the actual product. Is not it terrible?
Bolt of the thing that arrived was a thing that was Chrome plated.
Oh, sorry.
So I made this evaluation as a whole.
View detail
Thanks for selling as parts
Because it is a hexagonal head with Aluminum, I will lick immediately as I insert the Wrench tightly and do not tighten it.
Bolt will bend soon by falling.
I want a little strength.
I wish I could have sold only Bolt
Still, the hand guard of ZETA which is easy to get the parts is probably the best.
View detail
Tipping over, Bolt bent, so purchase
When falling, Hand guard Body did not have much damper,
Bolt only bent, so I bought this item.
When I bought it in second hand, because I had a hand guard, I got lost a little about how to attach it,
I was able to attach it safely. I remember that there was no Instruction Manual.
View detail
Only Bolt, I want you to join us.
Used for wr 250r. When I came back from the forest road there was no Bolt.
It is better to retighten.
I am not ordinary Bolt, so I got caught.
It was nice to purchase.
I wish I could sell bulk items.
View detail
In for Repair
For those who fall aside with Trekking it is essential Items' ZETAHand guard.
Bolt of Bar End was shaved while using, so I exchanged it.
It is fixed in Hexagonal Wrench, but mud and earth get into this Bolt hole
There are things often.
When detaching in maintenance, it is attention that it will be easy to make a snake unless you well clean the hole.
View detail
ZETA Zeta Bar End Adapter
I have attached ZETA's Hand guard to WR 250X, but when I saw suddenly, only the end portion was gone. I do not remember dropping after wearing, so it seems I went loose and flew by vibration.
It is appreciated to be able to buy it individually, but I think that it will be a little cheaper.
Tighten regularly regularly.
View detail
In substitute
Cut the Pro taper 's Handlebar, the favorite Magnum' s hand guard ceased to be attached ...
After checking carefully, there is a step in the inner part of Handlebar ...
Although I was at a loss, I decided to shorten the total length of Bar End mounting parts.
In this Parts, the total length was short and the price was reasonable too, so I bought it for purchase.
The installation fits perfectly and I was able to install the hand guard safely.
View detail
When dropped out
【What made you decide the purchase?】
During the Motorcycle race, the Bar End part dropped out due to vibration, and I lost it.
This part is necessary for the vehicle with CloseType Hand guard installed, so I bought it.
I can also use it for Guard parts of other Manufacturers, so I bought it for dropping it.
【How was it actually used?】
It is an essential part for Guard installation and Firmly fixed Hand guard.
【Was it difficult to install? (Hard parts case)】
Please be careful when installing, as Aluminum Bar and plug-in parts for iron bar are different.
【Please tell me the point of installation and hang (in the case of Hard parts)】
By vibration, Bolt tends to fall out, so fix Firmly mounting Bolt and let's tighten up occasionally.
[Is there anything I was disappointed about?]
I feel that the price is high except for non.
【Hope for Manufacturer - Please let me know if you have any improvement points]
Please make the price cheaper a little more.
【Have you compared items?】
There is none
View detail
It is easy to fall off
It is a part that is easy to fall out, so it was good to place an order with Single Item.
If you do not tighten up occasionally, it will be troublesome to fall off like me, so be careful.
View detail
Stock required
Once you knock it down, Handlebar fixed Bolt of this part turns before Handlebar and Hand guard bend.
Bolt besides low strength, but thanks to Handlebar because there was not bending, is it a dare to drop the strength parts ??
Off owns several cars and all hand guards are attached so we have it as a spare part.
It would be nice if Bolt alone could be sold as much as possible.
View detail
OEM → It may be necessary if you exchange it for external handlebar
Iron Handlebar (19 mm diameter) To Aluminum Handlebar (13. 9 mm diameter), so I purchased it because the Anchor of the hand guard that I used to date has not been included.
To be honest, scrap with File or CAInchor at DIY store (About 50 yen) I thought that I should divert it, but I thought of it due to temporal reasons. Bolt was inexpensive and it was good to purchase new as it can be replaced with a new one together (Lol)
Since it has not been overturned, we have not yet confirmed the ease of getting gaps seen in Review. I am not Gap at the place I hit Praghan ...
View detail
Since only one for Handles with a thick bore was attached, the place and Bar-end Adapters which purchased the Armor Handguard Bend in medieval times purchased.Although I who did check and did not purchase also have a fault, I think that it will be sav
Since only one for Handles with a thick bore was attached, the place and Bar-end Adapters which purchased the Armor Handguard Bend in medieval times purchased.Although I who did
check and did not purchase also have a fault, I think that it will be saved also when it has fallen and damaged if you sell separately per Parts in this way.
View detail
It is a thing used when Jeter's Hand guard made from an Aluminum is fixed to a Handlebar. Since it is exclusive elegance although the price is higher, it stops firmly. Can't it divert to Hand guards other than Jeter, either? in the case o
It is a thing used when Jeter's Hand guard made from an Aluminum is fixed to a Handlebar.
Since it is exclusive elegance although the
price is higher, it stops firmly.
Can't it divert to Hand guards other than
Jeter, either?
in the case of
, however a Motocrosser, it is vibration even if it binds tight quite firmly --
-- it loosens gradually -- a sake -- carelessly -- it tends to lose .
I think that it has and there is no loss when entering in a prolonged Race etc.
View detail
Since those who have attached the Hand guard are the things dropped unawares in the large Course which is a certainly lost Parts (smile), I have also lost 3~4 pieces until now (;_;) ... Again, Also when it lost by the Hand guard of an ACERBIS, although i
Since those who have attached the Hand guard are the things dropped unawares in the large Course which is a certainly lost Parts (smile), I have also lost 3~4 pieces until now (;_;) ... Again, Also when it lost by the Hand guard of an ACERBIS, although it was said that it was out of stock, by the ACERBIS, this product was able to use as it is! If it can do, I will want you to sell cheap only by a thread part (smile). View detail