Reviews
No operating noise.
There is no operating noise. It is Relay that chooses the body of the vehicle. View detail
No operating sound.
I bought this for the sound it makes as I am getting older and forget to turn off my Blinker. Is it because it is an LED Blinker? It's a shame because it's made in Taiwan and I could have bought a normal Relay for 350 yen on Amazon! 。 I feel like I've thrown away more than a thousand dollars in gold in a ditch. View detail
The silent type is really quiet.
"OEMRelay failed and I replaced it.
It's not impossible to repair a Relay, but it's difficult for an amateur and Universal Product isn't expensive. You should be able to replace it honestly.
PMC's have a peculiar cylindrical shape, which is a bit large. The later models of Motorcycles are square in shape, but there is no difference in performance.
However, the Socket part of Relay is available in 3 and 2 pairs, which are either compatible with hazard lamps or not.
Please note that this product is a two-foot, hazard-free construction. "
View detail
So far, no defects!
I use it on my WR250F.
It's been about a year since I replaced it and it's been functioning well with no problems.
It's solid and the quality is secure.
View detail
You can expect to hear a lot of noise
Kachicachi, hoping for a sound of movement and a replacement!
It is being used by XG250 TRICKER
My XG250 TRICKER, Normal muffler and very quiet Engine! But
When the Engine is starting, you can hardly hear it running
The BlinkerIndicator on the XG250 TRICKER is hard to see, so I forgot to turn it off Prevention
I chose to use the sound system, but I am disappointed
As for the Blinker relay, it looks fine
We do not recommend purchasing based on the sound of operation
My ears aren't covered in the trial, though I did check with Helmet
Even in that state, there is only a small amount of confirmation of operating noise and no effect
If it's late at night in a residential area and you're not running Engine, it might be just fine!
If your STD Blinker reley breaks down, I think this is a great product to recommend
View detail
And the noise it makes is just right
I bought this because my APRIO Blinker stopped blinking It's a normal bulb, front and back, but it works fine Because the direction of the hole of the attached rubber was different, I used OEM Relay's rubber to use The terminal was able to be replaced with no problem The moped without an indicator has the sound of operation I'm grateful View detail
It is a very good product
VINO (SA10J) The mounting. OEM's Connector does not fit,
I installed it with CustomWiring.
Polarity was not written on 2 pin terminal, I did it with intuition.
The first time you make a mistake, Blinker stays on.
The second connection is reverse connection. I properly flashed properly this time.
I was expecting the operating sound, surprisingly Small full face
I can not hear it in urban areas when I suffer.
I could be a little bigger operating sound.
Since the OEM's Blinker relay was out of order, comfortable and secure
I am satisfied with Large as I can run.
View detail
It was cheap.
Cospa Good!
Easy installation!
However, it does not blink or it is not sounded out. Is it an individual difference? - - -
Is it Ha Gap? - - - People who can fix it by myself are recommended
View detail
Since the pure Blinker relay broke, feel that the blink speed of . Blinker which is a pure Blinker ball is a little early for purchase . order, but. the Timing which . Blinker currently used satisfactorily begins to attach is pure -- si
Since the pure Blinker relay broke, feel that the blink speed of .
Blinker which is a pure Blinker ball is a little early for purchase .
order, but.
the Timing which .
Blinker currently used satisfactorily begins to attach is pure -- since it is more nearly very early, it can use quickly .
-- again,
.
also with delightful the Mount of a Rubber also being attached -- while merely using, the touch which is likely to shift from a Mount is -- although it was uneasy that the form of the terminal was not written to explanation of .
goods, use safely -- it cut (two terminals of Ha's character ?L handwriting ?).
View detail
It will not blink, if a Blinker is all changed into LED so that the direction of others may say. Since it is , it purchases, and it is satisfactory and I can be using the object for Addresses v125 made from a KITACO.
It will not blink, if a Blinker is all changed into LED so that the direction of others may say.
Since it is
, it purchases, and it is satisfactory and I can be using the object for Addresses v125 made from a KITACO.
View detail
[Webike Monitor] Although it purchased and equipped also with that it is a IC Type and a thing which has an LED operation track record in play [ other ] by the conclusive factor, it does not blink in case of order LED. Since it will blink if
[Webike Monitor] Although it purchased and equipped also with that it is a
IC Type and a thing which has an LED operation track record in play [ other ] by the conclusive factor, it does not blink in case of order LED.
Since it will blink if
one of the two is replaced with a NORMAL ball, it is not likely to be the fault of the relay [ itself ].
The relays corresponding to low power will be things to the last.
-- a Cost performance -- it is good -- although ... -- -- -- not too bad, since operation is carried out once.
View detail
[Webike Monitor] It was used for Blinker LED-ization of CRM250Rr. A relay pure to CRM and attached to it is a thing with a built-in Position function, and the form of a Connector is also different. I write removal of Digital-meter attachmen
[Webike Monitor] It was used for Blinker LED-ization of
CRM250Rr.
A relay pure to
CRM and attached to it is a thing with a built-in Position function, and the form of a Connector is also different.
I write removal of Digital-meter attachment and an unnecessary relay, and am remaking wiring of the circumference of a Meter from 1. -- Operation is not stabilized [ whether it is because it is low-temperature now and ] although it is a direction of the
products.
If the
Switch is turned on, it begins to keep being attached, without a Blinker blinking.
If the ON/OFF of the Switch is carried out as it is repeatedly, it will be repaired after all.
Are they such things as
IC relay?
View detail
[Webike Monitor] Since the order LED Blinker was used, relays are also exchanged. Although it is very cheap, it is used satisfactorily at all. Connector form did not suit but it carried out only the processing.
[Webike Monitor] Since the
order LED Blinker was used, relays are also exchanged.
Although it is very cheap, it is used satisfactorily at all.
Connector form did not suit but it carried out only the processing.
View detail
In order to set a blinker to LED as part of power-saving of RZ, this IC relay was chosen. Probably, the reason for having chosen this is a low price of a price too. And it also has quite high evaluation that it was able to carry out bolt-on to RZ
In order to set a blinker to LED as part of power-saving of RZ, this IC relay was chosen.
Probably, the reason for having chosen this is a low price of a price too.
And it also has quite high evaluation that it was able to carry out bolt-on to RZ by 2 pole pin.
Although the LED bulb had not been put in yet, the normal valve also operated satisfactorily.
A sound (tick tick sound when a blinker is taken out) of operation is likely to be more greatly [ than normal ] useful also for a failure to return.
Since various electronic autoparts had been added recently, it was settled well or was uneasy, but since the elastic band which has only a size like the pure plus alpha and can moreover be fixed to the same location with it being pure was also attached, arrangement as an ideal was completed.
It is buying it if it is this price.
The rest will be goods which we can recommend especially to the owners of RZ, if it moves firmly when LED is put in.
View detail
It is very good! Although blink speed was different in the time of taking out the time of taking out why or the left blinker, and the right blinker, since it became fixed, the relay appropriate for [ although exchanged for the relay (6V) attached to the c
It is very good! Although blink speed was different in the time of taking out the time of taking out why or the left blinker, and the right blinker, since it became fixed, the relay appropriate for [ although exchanged for the relay (6V) attached to the chaly from the first ] the aluminum attached from the first is very glad.
Moreover, a thing with a cheap price is also good.
Although the relay appropriate for new aluminum was found at other sites, since the price was a top for a while, it was carried out here.
View detail