Reviews
Fits: KAWASAKI KLX250, KAWASAKI D-TRACKER-X
For those who want to make the silhouette of the car look sharper...
I am an uncle who loves Fender Eliminator Large, so I was the first to replace it when I bought D-Tra.
Please note that if you buy only the product, you will not be able to use the reflector or the OEMB blinker, so you will need to purchase a reflector and a bracket to attach the OEMB blinker, which you may have lying around, before you can finally drive the product on public roads.
Now, as you can see in the image, the weight is reduced due to the overwhelming difference in area.
This doesn't mean that it is lighter or anything, but it is lighter (lol).
I personally thought that the Rear area was cleaned up and the finish was very cool.
View detail
Fits: YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R
DRC DRC MOTO LED Edge aluminum holder kit
Lighter than expected, looks good, and now that the Blinker has been replaced.
I feel like we should change it at this point.
View detail
Washer included is a bit much.
I wanted a red lens, but they were out of stock, so I purchased a Smoked lens and a Red lens as a Single Item.
Installation was easy, but the number of RubberWasher and Washers was a bit cumbersome.
I would also like to remove the entire Tail lamp when running Course, so it would be nice to see a little more refreshing in that area.
Wiring protection also seemed a bit weak for Off driving.
View detail
I could go to WR250F.
It was designed for WR250R and X, but I used it for F.
There is no Frame to the Tail, so we drilled a hole in the Fender to accommodate it.
The Number fixation I originally used was also a Fender fixation, so I don't think about vibration etc.
There were some unnecessary Bracket sections that had to be cut or something, but the thing itself is solid and quite secure.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D-TRACKER-X
Mounted on T2Racing seat cowl
To participate in RaceCategory, where only vehicles with numbers are allowed to participate.
Forcibly installed on T2Racing seat cowl by diverting another car model.
View detail
Appearance is perfect for sharp WR. The blinker was also made into the set. Although it is smoke, there is visibility of enough of daytime and it is a satisfactory level. It is dramatically pleasing.
Appearance is perfect for sharp WR.
The blinker was also made into the set.
Although it is smoke, there is visibility of enough of daytime and it is a satisfactory level.
It is dramatically pleasing.
View detail
This is the best Tail for Dr-z400sm
I did it at last. I thought that now is the last chance for the dr-z400sm which I owned in the past, and I bought a First Model Type in the shop of my father who likes Off-road Large in the neighborhood at a very low price.
So I immediately went to my dad's shop and had him put on a drc Fender Eliminator.
The Blinker Bracket is sold separately, but my dad's shop has it in stock, so I got him to service it for me.
The Fender Eliminator is a great match for the Racer dr-z400sm.
I don't have the car in hand now because it is still undergoing inspection and delivery maintenance, but every time I take a break, I go to see my car under maintenance and I am enchanted by its coolness.
View detail
If you want to convert DR-Z400SM to Fender Eliminator, this is it!
I think the back view of the Fender Eliminator, which stands out for its sportyness, is a good parenthesis for MOTARD.
Tail lamp with good color is more visible to the following vehicles than OEM tail lamp, and it is convenient for safety.
Not only DR-Z, but also trail bikes are familiar with DRC which is safe and stable.
Don't forget to install Reflector for legal reasons.
View detail
Fits: YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R
Not a bad shape.
Fender Eliminator and Quantity because I fell and broke my Stop-lamp.:I bought it because I thought it was a good deal in Set.
I'm a little disappointed that it doesn't come with a Connector as others have written.
Wiring is also available for the WR250R in Both Sides, Black, Yellow and Blue, and the included Stop-lamp in Black, Yellow and Red.
It is necessary to pay attention to the wiring of Black and Black, Yellow and Red, and Blue and Yellow.
When I connect Yellow to Yellow or Red to Blue, the auxiliary lights flash.
Also, of course, when you work on it, you have to turn off Ignition or Fuse will jump.
I inadvertently touched the Wiring when I was checking the lights and skipped the MainFuse (10A), so …
The blinker was originally from DRC, so I put it on as is, but it looks like it might go pop-drill depending on the angle of the fall.
It looks like I should add a Bracket and move it inside the Rear Fender.
The Stop-lamp is a little waterproof, but I'm not sure if it's waterproof as other people's Impressions say.
The mounting bracket of the Body seems to be sturdy, so that area seems to be good.
View detail
DRC MOTOLED EDGE ALUMINUM Holder Kit
I'd order DRC Motoled edge aluminum holder kit with smoke lens, the bracket is titanium color (not black color), but I like this color. I take about fifteen minutes to remove#31;the original license plate holder and OEM blinker. I use the LED turn signal light oringinal on Triumph speed twin again, so I change, customize and replace the hole blinker bracket (include) with 10mm stanless steel hole blinker bracket. It took me 2 hours to reinstall, great results, look very nice, more modern and sporty. The photo attached to the review. View detail
Fits: KAWASAKI KLX250, KAWASAKI D-TRACKER-X
Satisfied
I bought it because I thought it was a Fender Eliminator first
Because the blinker bracket that came with it was a hole of M8, it was substituted with the Homsen bracket I did The shape is satisfactory
View detail
I like Design
I am currently using the same product, but because I have been using it for over 10 years or because License Plate Light has become unavailable, I purchased it.
Stop lamp is getting dim. - -.
It is scheduled to be replaced early for safety, but it is hard to re-exercise Wiring which toughened Taping
Bold, is not it?.
I am happy that it has been manufactured in the same form even after 10 years or more.
View detail
I want you to think more about product concept
I think that it is not good that Seal is pasted and OEMBlinker can not be used.
OEM Product is integrated with Blinker.
I made it possible to use it using synthetic rubbers.
Initial product design that it can not be used OEMBlinker
It is wrong..
Even if you are diverting to other MODEL, this Concept
not good.
Also, do not cheat Wiring's connection with Bullet TerminalSet.
I'd like you to be able to connect to SUU using the same connector.
Thanks to it, it is true that I had amusement - - - (Lol)
It took about 2 hours.
Naturally, to be able to return to Sug at OEM
Bullet Terminal also attached to OEM Product.
(Because it is 400 cc, I also want Japanese Vehicle Inspection Correspondence. )
(Even though Headlight is dark and Large strange as well - - -. )
View detail
There is no problem as a product, but how about WR
We installed in WR 250 R. I bought it thought that it would be better to trade with Tail lamp
OEM seemed to be Parenthesis good, just Fender Eliminator just did not use Tail lamp.
I think that it would have been better if you bought the person of Repair Parts, but another Motorcycle (CRF250L) So I can use this Tail lamp for now. Since I did not use the Tail lamp this time, I purchased the LED License Plate Lamp separately. Although it is Parenthesis when attached to CRF, WR is definitely Parenthesis better if OEM is better.
View detail
Fits: YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R, YAMAHA WR250X, YAMAHA WR250R
Rear tightens, Parenthesis will improve
Fender Eliminator Kit is troubled because there are many kinds, but this is Recommendation. Off Because the fall is an attachment, it is safe to make it easy to correct even if it is distorted.
Photo Blinker made Bracket by processing Aluminum plate and attached Posh's one. It tightens more than NORMAL Pon attachment!
View detail
Parenthesis Is it okay?
LED of License Plate Light does not light with initial malfunction ...
Because I corresponded promptly, although there is no complaint, I felt the accuracy of Bolt kind too low. I do not want to attach or remove again many times.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D-TRACKER-X
Fender Eliminator
Purchase to make Rear clean. Since OEMBlinker is not attached, replace with LED Blinker. Although attaching is easy, it is necessary to separately prepare the Coupler separately, although it is exclusively for the car model. It is good that it is attached to the Coupler. View detail
DR-Z400SMFender Eliminator
Before purchasing this product, I bought a similar item, but the similar item could not be installed with inferior goods.
Since it was after bought bad goods, it was uneasy whether it could be installed, but properly translated (Instruction Manual for easy entry as well as a simple installation drawing is stated and there is nothing to worry about mounting was. Also, Rubber Bush comes with and I thought it was wonderful to be able to slightly reduce the vibration from the car body.
There was nothing that caused the bulb to be broken in the item I purchased for the LED. I think the amount of light is enough. Lens color was changed to Smoke together with Blinker. I feel a sense of unity in Tail, I am very satisfied.
The bad thing is that Waterproof's processing is sweet and when riding in rain, water enters a little in Lens. It seems that it enters through a hole that passes through Wiring in Rear, not between the gap between Lens and Body. Water wound by Tire is entering. I would like to take the treatment on my own earlier.
View detail
Is good
Because thick Aluminum material is subjected to Shot blast treatment and finished with Gray's Anodized, feeling is high in addition to your own thoughts. LED Lamp also has enough illuminance, you can nod your heart like Off Standard car Custom.
OEMBlinkerMount Bracket was out of order so I searched for it with ok. It's a shame only here.
View detail
Fits: KAWASAKI KLX250, KAWASAKI D-TRACKER-X
Repurchase by transformation due to falling
Because the Aluminum Holder I had attached was deformed and repurchased. The basic set is Edge Tail light only with Aluminum Holder and 8 mm hole Bracket, but it is quite expensive for Edge Tail light 3000 yen Plus. 8 mm hole Bracket is difficult to install and the black paint of 8 mm hole Bracket will also rust soon etc etc. Although there is somewhat dissatisfied, the Fender Eliminator Kit has only this choice and has re-purchased.
View detail