Reviews
Ideal for small adjustments
I bought a battered 900SS (900SL) and am Restore.
The frame was not bent, but it had a history of falls. After restoring and reassembling the frame, it was discovered that the Right Footpeg Holder was slightly inside the body of the vehicle.
The Frame had already been painted, so it was impossible to correct it now.
It is not an easy place to turn in the first place, and the correction is extremely difficult because the turn is really very slight.
I thought about installing an unnecessary footpeg and forcibly bending it back by sticking an iron pipe into it, but the footpeg holder part is integrated with the seat rail, and that seat rail is integrated with the main frame.
When I corrected the footpeg bend, it seemed that the bend would appear in an extra part (probably the seat rail section), so I decided to swing the footpeg plate outward with a collar in between, which is a bad idea.
The color used this time is a mere 2mm, so there is zero discomfort associated with wearing it.
It doesn't bother me at all
And the gap between the Swing Arm and the Swing Arm is now about 3mm in areas where the gap was almost Zero.
I wondered whether I should choose the slightly more expensive Black Anodized Aluminum color, but it was a Large decision to go with the Silver color (no Anodized) since the location is relatively visible while parked.
We succeeded in Offsetting by 2mm with almost no noticeable difference.
The color material also seems to be a hard material, not just raw aluminum, and there is no sign of deformation even when sandwiched between the M8 Bolt's Large Torque.
This should eliminate the need to buy expensive parallel Washers in most places.
View detail
To prevent deformation of the Footpeg Holder fixation area
I bought a battered 900SS (900SL) and am Restore.
There was a history of a fall by a previous owner, and although the frame was not bent, the footpeg holder was slightly bent and tilted inward, and when the right footpeg was attached, there was only 2mmm clearance with the swing arm....
Leftfootpeg has a Clearance of about 5mm, so I purchased this collar to be inserted between the Footpeg Holder and Frame to ensure this Clearance.
Separate Quantities:Pair (for Left and Right) The gap does not have to be aligned at 2mm, but 2mm is indeed too narrow....
There are cheaper aluminum collars, but those cheap ones are made of the same soft raw aluminum material, not parallel or anodized....
The base of the Footpeg Holder is a part that is subject to large forces, and it is a part that can be seen to the fullest extent.
Material is not specified, but looking at the coloration of Anodized, I wonder if it is in the 6000 range?
It feels like a round bar of extruded material that has been machined.
Perhaps we did not dare mention the Material name because we could not use a good sounding name such as Duralumin or Super Duralumin.
But if it's in the 6000s, it's rather wishful thinking.
Exactly for use in external visible positions due to its high corrosion resistance.
Of course, unlike cheap products, they are very hard and will not deform or crack even when tightened with an M8 bolt.
Small items such as these tend to focus only on cost performance, but it is only natural that good items are expensive.
If you procure colors from Home center for cosmetic reasons, they are bound to be white, powdery, and shabby in a year's time.
For those who think that the most important thing is not the price in the immediate future, but the ability to remain solid for several years to come, the Quantity is a small fraction of the price of the original product.:2pc. This product, which is available from Set, is convenient and geeky.
View detail
For fine tuning
Used to compensate for Cowl Bracket Gap in combination with other thicknesses of Spacer View detail
Spacer
Purchased to fine-tune the standing width between the Screen and the Screen stay. View detail
uplift
It is used to create an angle between the Screen stay and the Screen. It is black, the same color as the Bracket, so it does not stand out and is unobtrusive. View detail
Used when installing Sissy bar
There were no problems with quality or installation. View detail
Purchased for Sissy bar installation
There were no problems with quality or installation. View detail
Quantity:It was 1 Set of 2pcs.
I should have looked closer, but the Quantity:1 Set of 2pcs. without noticing Quantity:I bought 2 Sets.
I needed the color to make Rear Sets for footpeg, so I bought it for that purpose.
View detail
Used for installation of Rear Sets for other vehiclesOEMfootpeg diversion
Purchased as Spacer for Rear Sets installation on Z650 (Zapper) with OEM footpeg for GSX-R750.
Although it is possible to install the washer by using a stack of washers, we chose this product to improve the appearance.
No problem to install as the inner and outer diameters are the same as the Washer. The appearance has been improved to a large size, and I am satisfied.
However, if the height is WasherQuantity:The difficulty is that it is not possible to replace it completely because it was short by 1 pc.
View detail
Rear Sets installation using OEM footpeg from another car
I bought this as a spacer to install Rear Sets on my Z650 (Zapper) which is a GSX-R750 OEM footpeg. 1pc. is just a spacer and the other one was cut down on the side to fit along the plate. It was easy to process because it is made of aluminum. （I inserted a washer of the same diameter for the slightly insufficient height (as a matter of course), but it would be nice if the height could be adjusted in 2mm increments. View detail
alignment
Rear Sets position, used to avoid interference.
Quantity:1 Set of 2pcs., good product at a reasonable price.
View detail
alignment
Rear Sets are installed for alignment and fine adjustment.
Size type, Quantity:2pc. Set-in, the price is not that high, which is helpful.
View detail
Suspension collar
Used for Suspension Diversion More Looks and Accuracy than Overlapping Washers Size not found in KCON View detail
It can be used for many things, not just 4mini.
Used as a spacer to attach the Master Cylinder of the Disc brake to the Rear Sets of MONKEY's for Drum.
This kind of Spacer has a lot of use for something, so it is nice that it is sold at this price.
View detail
Center out.
[How is it used?
I bought an external wheel from Spare, but the brake disc did not fit in the center of the Caliper, so I used this Spacer to adjust the center.
At first I tried to recreate the Wheel color, but it was a pain in the ass, so …
Was the one you received as per Image?
As per Image
It's a beautiful finish.
Was the installation difficult?
Simply insert it between Caliper and Caliper support.
How was your experience with it?
The disc is now in the middle of Exactly.
[Included Parts:were they on?
Not particularly
[Was there anything that disappointed you?
Not particularly
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
They have spacers of various thicknesses and sizes, which is helpful for Privater.
View detail
Substitute for RearCarrier color.
I used this product due to the relocation of the rear blinker.
The size of the bracket is very good.
View detail
To fill in a small gap.
It is a beautiful and inexpensive way to buy a light. View detail
Convenient colors
I bought a used Slash guard for XJR400R, but it didn't have the attached color etc., so I used this one instead.
I really wanted to get the 60mm color, but none of the manufacturers were offering it, so I got the 30mm×Quantity:2pc. I substituted this product in Set.
The color of the product is also Black, so it does not stand out strangely, and I am very satisfied because it is made carefully and is inexpensive.
View detail
Instead of Shim adjustment of RADIAL CALIPER
Used for Shim adjustment of RADIAL CALIPER.
I changed the Rotor to a slightly larger one, so I used it to position the Caliper.
I am satisfied with the accuracy of this product.
I love that it comes in a variety of thicknesses.
View detail
For adjustment.
I used it to adjust the width of my DAYTONA rear stand hook!
I put on 3mm, but I think 5mm would have been better…
It is helpful to have various Size.
View detail