Reviews
Match the color of the car body.
Deep orange was selected to match the body color Orange.
PackageThe color before opening the package looks somewhat Orange or Red under the light.
Easy installation on vehicle body with only M6 cap bolt
Under sunlight, the Orange color was consistent with the color of the car body.
No BALI, etc. and quality seems good.
View detail
Importance of imple
[How is it used?
It is installed on a jc61 grom OEMHandlebar.
Dress-up and Suma Holderetc. installation purpose.
Was the one you received as per Image?
I love it so much that I Repeat it.
Was the installation difficult?
It was about 10 minutes.
How was your experience with it?
I am not sure if it is because I could not install it in the correct position this time, but it feels a little more jittery in my hand than before.
[Was there anything that disappointed you?
I made the mistake of buying it because all the impressions I saw said that 187mm was JUST the best for Groms, etc.
The jc61 is not 187mm and is more expensive, but the length adjustable Type is better.
With proper installation, the way Clamp fits is obvious.
I don't think it makes sense unless the face of the Clamp and the face of the Handlebar are Exactly aligned.
I will consult with Wallet and replace it with Posh's adjustable Type.
View detail
Good quality
Good quality, well built. The inside diameter of the clamp is correct for 7/8" handlebars. The only issue is that the braces sold by this company would not get tight when clamped, unless you add some washers. View detail
Installed in conjunction with POSH Handlebar Brace
Together with the Handlebar Brace, it will cost about 4,000 yen,
I thought it was more reliable and cost-effective than buying a product from a no-name manufacturer.
View detail
Used with the handlebar of the model, it will match well. love it View detail
Handlebar Brace side thickness needs to be adjusted
I purchased this product at the same time to install the Handlebar Brace. When installing it, there was a gap on the Handlebar Brace side, and it was wobbly even when tightened tightly, so I installed it with two extra washers I had at home. If the gap is filled, there is no wobble, but if you install it normally, there will be a gap of 2 to 3mm, which is not an individual difference. Personally, I think it would be better if the color were a little more subdued. View detail
A little overpriced.
The Red color has faded away so I replaced it with Silver. I don't remember the length of the brace, but the standard length brace has a quantity angle for CB400.:Pair (for Left and Right) Brace is recommended to be a little shorter. I wrap a gap tape around the handlebar clamp to prevent damage to the handlebar and then tighten the clamp. View detail
A set of the circumferences of a preparations handle was changed into commuter rapid-service specification. As a result of examining many things, the product made from POSH out of which a feeling of unification comes was used. A handle bracket, a
A set of the circumferences of a preparations handle was changed into commuter rapid-service specification.
As a result of examining many things, the product made from POSH out of which a feeling of unification comes was used.
A handle bracket, a handlebar, a handle brace, a handle brace clamp, bar end, and a heavy weight nut were made the product made from POSH.
Color was unified by champagne gold.
When the vibration at the time of a run was reduced, there is also Schopp's recommendation and it equipped with the handle brace and the handle brace clamp.
Since the direction of the effect carried out simultaneous wearing also of heavy weight bar end and the heavy weight nut, the effect of the simple substance was not able to be checked, but it became the feel gently carried out compared with normal as the whole being operative.
Since there were also the master cylinder of a brake and a clutch and hose exchange besides the above, attachment was requested from Schopp.
However, as long as a configuration is seen, even if it equips by itself, I think that it is possible in about several minutes.
Since the master cylinder of a brake and a clutch also chose the gold of the daytona nisshin, there is a feeling of unification, and it was finished in the satisfying thing.
View detail
Without this.
Of course, without it, the bar will not be attached.
There are a variety of colors to choose from, so you can even choose different ones.
Yes, it is.
View detail
The quality is good, but the price is a bit high.
This is a replacement from the Gold color that the previous owner had. There is a gap on the Left SideClamp, so I will use a Washer. Durability (Painting) will be reviewed in the future. View detail
Good
I was worried about the color. I chose champagne gold to match the color of the fork on the Grom, but gold might have been a closer color. I didn't want to scratch it, so I put a thin rubber sheet between the screws. I didn't want to scratch it, so I put a thin rubber sheet between the screws. When I have time, I'll try to fix it with a washer. View detail
Sold separately from the Handlebar Brace.
I bought this clamp along with the Brace to install the Handlebar Brace on my Honda, Grom and JC92.:I think they should be sold as a set, but.... When I installed it, I dropped it on the handlebar and the paint on the handlebar peeled off a little. I think it's a very reasonably priced part, so it's easy to get for custom beginners.
The installation was a bit tricky to get the Brace straight and at the right angle, so I had to temporarily tighten it several times, move it away, check the angle, and repeat.
I was worried about the length of the supplied bolt, so I bought a bolt 2mm longer than the supplied bolt from Home center and used it. I'm very happy with it!
View detail
Use this to install the bar. Tho It's a little bit expensive for what it is, I bought it. The quality is mediocre, but if you want the color to match the bar (from the same brand) you need to buy it. View detail
Easy installation
I decided to install the Handlebar Brace because I was worried about the vibration of the Handlebar, but I was going to use the one that came with Hardy's Handlebar, but the clamp is not an open type, and I had to remove all the things attached to the Handlebar to install it. It was necessary to remove all the things attached to Handlebar, and it was troublesome, so I came to purchase this one. The product is solid, and there are no problems with the texture, color, shape, or finish, and I think the cost is good. I dropped it during the installation process, and of course, the paint was scraped off and Wound came in. If you are concerned about the wound, please work carefully.
The thickness of the joint of the shaft is different from the one of posh. I had to shave off about 0.5mm from the joint on the shaft side to be able to fix the clamp to the handlebar, and then I moved the Radar and Smartphone Holder onto the shaft. It was very easy to install thanks to this Clamp. The effect on vibration is subtle. It seems to be effective, but it may be my imagination. I will try to think of something else.
As for the Shaft, it was a little long, so the mounting position became high, and I don't like the position of Radar and so on a little. I'm thinking of buying a posh shaft of moderate length in the near future.
View detail
Parts required to install Handlebar Brace
This is required to install the Handlebar Brace. View detail
Solidly built.
I bought it with the same manufacturer, Brace, but I didn't learn enough and it was too Exactly I couldn't adjust Clamps, so I shaved a little bit with Grinder, but I shaved it off. The cylinder hides the cylinder so there should be no problem with its appearance.
View detail
Purchased Mat titanium
MONKEY (Z50J) Because Knob of Left Side Hondlebar is shifted by vibration,
As a countermeasure to that, I bought it with Race Shaft at the same time.
Since it is simultaneous with Race Shaft,
Impre will be with Race Shaft,
I have not run yet, but I was able to experience the effect just by pushing and pulling the car body.
I made Shaft Blue and Clamp Mat titanium,
I think that it is good to be able to combine with your favorite coloring.
View detail
I have a good texture.
I installed it on the ZrX 1100.
It is OEMHandlebar. Choose Blue to fit the car body color.
Installation is simple. OK with on-board tool. Feel satisfactory.
Although there is no change in running, there is a sense of messing around and I am immersed in considerable self-satisfaction.
The purchase reason is the installation of ActionCamera. It got together beautifully.
Shaft and Quick Release Brace Clamp purchased with Set.
Shaft does not come with us, so please join us.
Since both Color are abundant, various combinations can be done.
I tried to Blue and Matte Black. I like it..
Impression sentences are the same as Shaft, but I changed the pictures.
View detail
It seems easy, but a little Large strange?
Installation itself is easy, but Quantity : Pair (for Left and Right) It is difficult to fix it while aligning the position.
Brake - Around Clutch - Handlebar OEM - Clearance is quite tough if it is NORMAL.
View detail
Easy installation!
Shaft and Color should be combined.
It can be combined with Color of the car body, it will be one point dress-up.
It's easy to install and it will not take 5 minutes.
If you only pay attention to Shaft's Length Clamp is fine.
View detail