Reviews
Low price but sufficient Quality
The price of Motion pro was too high, so I went with this one. The price is a quarter of the price, but the quality is solid and this product should be sufficient. The box is just a bonus, and the lid closure is so roughly made that it won't close after a few uses. View detail
MINIMOTO Regulator from 6V MONKEY Silicon Rectifier
I installed it on my 6V GORILLA, I bought it to customize it with 6V, the voltage is very stable and the battery life is longer. I will continue to ride on the Large Cutter while maintaining it. It has been my partner for more than 40 years. View detail
Getting the Center out is the hard part.
I was prepared for BALI and Small scratches, but I can't get the Center without modifying the Brake Panel side.
I also bought a 4mm Sprocket spacer but I think it will be useless.
Also, there is some distortion, so if you want to assemble it tightly, we recommend a reasonable price.
View detail
Great tool, highly recommend
This way is much more precise. Works like a dream. Bought this tool for removing the small KTM Bendix bushings. It worked perfectly. Great tool for the price, was able to remove all of my bearings from my transmission in my KTM plan to rebuild my KTM with it as well, didn't have an issue with any of the small sizes, you just have to be sure that you are setting it up properly. Note that you'll need up to a 26 mm wrench or a crescent wrench. Seemed a little pricey for a tool you do not use that much but it will serve generations of riders in the family. Tips: Don't forget to grease the sockets, center them exactly and tighten them. View detail
Fits: HONDA SUPER CUB 50, HONDA CHALY 70, HONDA CHALY 70, HONDA CHALY 50, HONDA CHALY 50, HONDA CHALY 50, HONDA SUPER CUB70, HONDA SUPER CUB70, HONDA CHALY 70
Used for CUB
[How is it used?
CUB's fuel tank cap was destroyed, so this is used
Was the one you received as per Image?
It was as per Image and there were no problems.
Was the installation difficult?
Installation accuracy is good, and it can be used with the same degree of force as the OEM.
It's a pontoon.
How was your experience with it?
Since it is thinner than the OEMTank cap, Fittingetc. can be installed without worrying about anything.
However, as is the case with OEM, there is a part where it feels a little difficult to turn a slightly thinner cap than OEM in order to turn a slightly more reluctant tank cap.
[Was there anything that disappointed you?
Not particularly
I think this is cosier than looking for a used one with Key cylinder.
View detail
In the Chinese VM Setting
[How is it used?
For some reason, Throw of Chinese VMcarburetor has this Type, so I used this one for setting.
Was the one you received as per Image?
The Sponge dividers were quite nice compared to the usual divider-only Packages.
It is good because Jet does not mess up inside.
Was the installation difficult?
Accuracy is adequate. There were no problems.
How was your experience with it?
Smallest SizeQuantity for SmallEngine Displacement Volume:I thought that with Set, I could Cover all of the Setting range.
It is said that OEMs are more accurate and better for jets, but if the mother company is a Chinese carburetor, I don't think it will be a problem.
[Was there anything that disappointed you?
None in particular
View detail
MINIMOTO6VMONKEY Silicon Rectifier Fire to Regulator
I have two 6V GORILLAs, so I installed the first one and the voltage became very stable and the battery life improved dramatically, so I installed the second one as well. I did not want to change to 12V, so I bought it to keep driving with 6V. View detail
Universal but...
I was looking for a Universal Oil filter wrench and found this one.
Compared to other companies' products, we chose this one because it can accommodate a large diameter.
In fact, I used it for Oil replacement and found it very nice that the Socket is compatible with 9.5 and 12.7.
However, the part that grips the Filter is still bare steel, so it will scratch the Filter when tightened.
The Oil Filter is basically out of sight, which was a little disappointing.
View detail
Universal Product
I bought it to clean the parts that were soaked with oil.
It may be a little soft, but I will adjust it by cutting it a little.
View detail
Well, it is about the same price.
It needs a little processing, but I think it's a good cosmetic product. View detail
Pipe Handlebar/Clamp, but as a Fog Lamp/Clamp.
I was looking for a clamp for the Fog Lamp, and since the Pipe diameter is 22mm and it is an M10 Bolt, I thought it might work, so I did some research and found that it might work, so I purchased it.
I wanted to hang it straight down from Clamp, so I was satisfied.
Of course, Bolt and Nut are purchased according to their length at the time of installation.
View detail
For ChainSelfMaintenance
I had been doing maintenance of the chain by myself, but I was not satisfied with the results, so I decided to purchase the equipment.
Both parallel and perpendicular can be checked.
Analogous method, but therefore reliable.
I think it is a good item to have, and I recommend it to those who do maintenance of looseness and deflection of a chain by themselves.
View detail
Fits: HONDA GORILLA, HONDA MONKEY
Required for Carburetor setting
Packing is essential for carburetor setting, etc., which requires multiple carburetor body roses.
Quantities, since rubber packing usually dies when opened and closed before aging.:It might be nice to have at least 2 Sets.
View detail
Among the many that are out there.
I chose this product to get Chain Alignment since I changed the Chain of MONKEY125 to Seal chain.
The reason why we chose this type is that there are many types of this type from various manufacturers, but the Screw that fixes the Sprocket to the Material:Plastic, and that was the criterion for our choice.
It is not a good idea to get scratches, no matter how hard it is to see them.
I got a 40cm Aluminum rod separately because the Aluminum rod was too short according to the reviews from other seniors.
I think it is cost-effective if it is mentally satisfying, although I think it can only provide a comforting adjustment.
View detail
It's cheap and there's a lot of it, so don't be afraid to use it.
I bought this for a variety of versatile uses.
For the time being, I plan to use it to wipe down after car washes, spray up simple coating agents, clean Helmet, and if there is any left over, to clean the house.
I thought it was a Small one after reading various Reviews,
It was a bit larger than I expected, just enough to cover the top of the helmet. (I'm posting a picture.)
The texture is the same level as that of common micro fiber,
It is not of a particularly high quality, but I think the strength of the Largeest is that you can use the GunGun without hesitation, and it does not get scratched easily even if you wipe up the Cowl.
I would buy it again when it runs out.
View detail
Pimping to 12V square eye CHALY.
Fit is perfect.
Small is not wired.
The fact that it is made of glass is also an added bonus.
Chinese LEDs are installed on these to ensure brightness.
We had a good shopping experience.
View detail
Fits: HONDA MONKEY, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY, HONDA GORILLA
The footrest for Monkey
I bought a footrest for a Honda Monkey, I really liked it because it is made of aluminum and is not adjustable - the length of 19 cm is what you need. It came up without any problems, the installation is fast and easy. The price and quality are minimal. I recommend it to everyone. I bought a footrest for the Honda Monkey, I really liked it because it is made of aluminum and is not adjustable - the length of 19 cm is just right. Fits without problems, installation is quick and easy. Minimum price and quality are high. I recommend to all. View detail
Fits: HONDA SUPER CUB110, HONDA CROSS CUB50, HONDA CROSSCUB110, HONDA SUPER CUB 50
It's a bargain
It is a simple Side stay.:Pair (for Left and Right) I think this price is a bargain at
There is no instruction manual, but anyone can install it with minimal tools. The quality of the product is in line with the price, but it does not bother me because of its simple shape. It has only been installed for a short period of time, so I am not sure about its durability, but I think it is solidly made without any rattling.
View detail
Fits: HONDA APE TypeD, HONDA APE 100 TypeD
Satisfaction can be obtained in both appearance and performance.
Aluminum case and bright red Spring color increase the impact of the look and feel. (^^;)
Spring rate seems to be more flexible than OEM when you drive it, and
I felt that the Dumping was firmly in place and the Rear was more stable.
I personally appreciate the fact that the total length can be adjusted with the pre-road fixed, but the Hook wrench
It is not included, so those who wish to adjust it must purchase it separately.
View detail
Rusted and replaced
I purchased the same product a long time ago, but it rusted due to neglect, so I purchased the same one from here this time. Rust in the tank is unavoidable, but the exterior is clean and the quality of the product is good enough. View detail