Reviews
Fits: HONDA PCX125, HONDA PCX125 Hybrid, HONDA PCX150, HONDA PCX160, HONDA CB125R, HONDA CBR125R, HONDA CB250R, KAWASAKI Z125-PRO, HONDA PCX125 E:HEV, Others , YAMAHA BWS 50, YAMAHA BWS125, YAMAHA MAJESTYS, HONDA ZOOMERX, HONDA MONKEY125, HONDA glom, HONDA CROSSCUB110, HONDA DAX125, HONDA CT125CT110 HUNTER CUB, HONDA CL250
KITACO Helmet Holder
Installation was quick and easy. Before releasing the bolt, you must remember the original position to hold it in its original position. I bought a high-quality product, so if someone asks, I will highly recommend it. View detail
Fits: KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-)
Necessities
The OEM helmet holder position on the ninja is not good enough for the helmet to hit the footpeg, so I installed this. It is very easy to use and I wonder why it was not in this position from the beginning. When you remove the helmet lock, you have to remove the t30 screw, but be careful not to lick it, because the screw lock is painted and very hard. View detail
Fits: KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-)
Necessities
The OEM helmet holder position on the ninja OEM would not allow the helmet to hit the footpeg, so I added this. It is very easy to use and I wonder why I didn't put it in this position from the beginning. The t30Screw is coated with a screw loosener when removing the helmet lock, so be careful not to lick the screw. View detail
Fits: BMW R1200R, BMW R1200RS, BMW R1250R, BMW R1250RS, BMW S1000RR
It's perfect
We had a Dealer install it on a BMW R1250R in 2023!
The labor cost was 1,650 yen.
Very useful.
View detail
Absolutely necessary!
It is a must-have product because Eliminator's OEM Product is not easy to use.
It is easy to install and very user-friendly.
View detail
Fits: SUZUKI GIXXERSF250, SUZUKI GIXXER250, SUZUKI GIXXER150
That would be handy
The DL1000 V-STROM250SX is mounted on the same frame as the Gixxer 250, so no special modifications were required.
Wrap the Rubber around the Bracket and insert it into the Bracket.
*Because it is only clipped by Bracket, it is better not to run with Helmet hanging down, because there is a risk of it coming off.
I don't think I'll be using it much since I have a top case, but I think it will come in handy when I have a full load of souvenirs, etc.
View detail
It is easy to install.。
You only need one Hexagonal Wrench to install it, just apply Screw lock and tighten it. I always buy helmet locks from this manufacturer because they are inexpensive and the quality is very good. View detail
I would also like to see the foundation for Right Side *.
The screws holes for the SIDE vernier mounting bracket on the GSX-8R Tandem Footpeg Reverse side are used for SMART mounting.
As others have mistakenly said, Install the foundation with the smooth side on the outside (the one with the loci on the inside)." The first one with Logo is installed on the outside, and the second one with Logo is installed on the inside. Holder upside down?" I panicked.
View detail
Very convenient!
First of all, this product is per Large! It's a Dial type so you don't need a key! I didn't realize how convenient it would be to just use it…The texture of the switch when you press it is also great! The weight is reasonable and the build quality is good! Once you use it, you will never go back to the OEM Helmet lock which is hard to use! I will never go back to the OEM hard to use Helmet locks once I have used them! View detail
Postscript to postscript!
You probably think that a helmet is something that someone else is using in direct contact with your skin, and that there is no reason for someone to steal such a thing. The idea of a thief is that he/she wants a helmet for a Tandem person. So don't think that because the helmet is large, it is durable or that the probability of it being stolen is low. View detail
Postscript.
In my opinion, the screws of this Helmet lock are Large, which is an oddly soft material. In my opinion, the screws that fasten the Helmet lock are Large and are made of an oddly soft material! Therefore, it is safer to work with caution and take it easy or Shop.
Helmet locks themselves may be inexpensive, but helmets are expensive, and if they are stolen, you will not be able to get back on your motorcycle.
View detail
I was relieved that it was as good as I imagined.
The vehicle used is z900RS.
Due to the convenience of installing the Side Back on the opposite side of the Exhaust System. The existing helmet holder could not be used.
Then, I thought of for Tandem, Helmet holder.
It can be installed on the opposite side of the existing helmet holder.
This product has arrived. It looks the same in appearance as the existing OEM product.
I wondered if the existing helmet holder could be attached to the bracket as it is, and it did so without any discomfort.
In other words, the Helmet holder that can be used with the Engine key arrived on the opposite side of the existing one.
View detail
It takes hang to tighten.
With a diameter of 22mm, it was installed on the Pipe of SP Mukawa's Carrier.
I had to bite down on the Rubber to tighten it, but it was very hard and difficult.
I think the role as Helmet holder is not a problem.
View detail
Ease of use unique to Exclusive Design
[How is it used?
RC42 has a Helmet holder if you don't remove the Seat.
It was inconvenient when I was on the road because I could not use it. I was looking for a product that was easy to use, and I found this product and purchased it with high expectations for its exclusive design.
Was the one you received as per Image?
Almost as per the Image.
Was the installation difficult?
Installation was very easy!
The only tools used are +Driver and 5mm and 6mm Hexagonal Wrench.
How was your experience with it?
Balance varies slightly depending on the type of helmet.
It is a Level that is not a problem.
[Included Parts:were they on?
The key is Quantity:Includes 2pcs. Includes a helpful Instruction Manual.
[Was there anything that disappointed you?
None in particular.
View detail
Slightly difficult to install, but functions well
Helmet holder for retrofit type.
Demerit is that it doesn't come with a key from the beginning like Kawasaki does these days...
It is 100 times better than hooking up to a Tandem seat.
Functionality is adequate.
There is a slight problem with the installation, because the Bolt that holds the Plate is close to the body of the car,
In a normal hexagonal Wrench, Quantity:Only 1 pc out of 2 pcs could be tightened.
I think it can be tightened by Offset wrench etc. because there was a gap of about 20mm when I temporarily tightened it by hand.
Also of note, this Helmet holder uses the Bolt hole on the back of the Tandem Footpeg.
Since these are probably bolt holes for installation of OEM SoftSide case brackets, it is necessary to confirm whether they can be used together or not.
View detail
I think I got the wrong model number….
I don't know if I got the year wrong, but I couldn't fix it with 2 points, but with one bolt, so I'm a little worried. I am satisfied with it. View detail
Helmet lock
I had been thinking about installing the Helmet Lock Holder, but finally decided to go with METALGEAR, View detail
Can also be installed on the GSX-S1000GX.
[How is it used?
In the photo, I used a helmet, but I was concerned about the load on the chinstrap, so I installed a wire lock and used it to lock the seat bag.
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
It was easy to install by simply removing the Bracket from the Tandem Footpeg.
The Bracket is quite heavy, so recommends that you remove it while holding your hand on it.
How was your experience with it?
I am satisfied because I don't have to take off the tandem seat any more because I don't have a helmet holder.
[Included Parts:were they on?
Key Quantity:2pcs and Instruction Manual, 2 KIJIMASticker
[Was there anything that disappointed you?
I was expecting to be able to convert it to one-key, but the keyway was the opposite type from the vehicle. If you want to convert to one-key, it is difficult to purchase on Net.
[Availability and clarity of the Instruction Manual
Even the Torque value of the BracketBolt of the Tandem Footpeg was kindly listed.
[Opinions and requests to Manufacturer
The GSX-S1000GT and RearSub-frame seem to be the same and can be installed. We would appreciate it if you could add it to the list of compatible models.
View detail
The construction is very good, but when you actually use it, it is very difficult to use.
The make is very good and looks OEM 。 I put it on my MOTO GUZZI which does not have a helmet lock, but it is attached without any discomfort. 。 However, in actual use, the helmets touch the exhaust system because of the low position of the helmets. View detail
I am very satisfied
Installation of the product is very easy. Also, the delivery of the product is very fast, and the product description page and configuration are the same. View detail