Reviews
Just attach it to the phone cover.
Quantity to Holder:Set is 90-degrees rotation, so the phone is in portrait and the Quantity:Set or beside Quantity:Set or not Set is determined by this orientation.
I can change it on the Holder side with Hexagonal Wrench.
I use it every time I go touring and have no problems.
Large Variety Satisfaction
View detail
For those who don't want to stand out with SimpleStyle
There are many different Smartphone Holders, but I think this product is the most discreet and easy to install.
In fact, it is so close to the Top Bridge that its presence can be eliminated.
If you want visibility, you can choose a Type to attach to the Handlebar.
Installation on the Holder is simply a 90-degrees rotation to fit the groove.
It will not loosen or fall off.
Satisfactory product
View detail
No worry about falling off.
There is no sign at all that the 120km/h section of the New Tokyo-Nagoya, the Decoration bumpy road, or anywhere else you might fall off.
Vibration absorption capacity is also very high.
I have tried a few and they are by far the most secure in preventing drops, and if you are really worried, you can easily lock it with Lever.
It is very easy to use as it is easy to connect Charger.
The only complaint I have is that it is difficult to clean because dust tends to accumulate in the groove where it is fitted.
Also, some people have a problem with the way it looks. (Depending on Motorcycle) It may seem a bit lumpy.
View detail
Fits: Others
Mounted on CUB 110cc Crank bar
We replaced the Rubber part of Crank Bar's Smartphone Holder with this one.
When I run, the phone is still vibrating in Small increments due to vibration. I'm not sure how much the vibration is reduced, but I think it's good for preventing breakdowns.
View detail
Holder's clattering sound is gone.
[How is it used?
I bought this product additionally because I was told that iPhone breaks Camera by vibration.
Was the one you received as per Image?
It was larger than I expected.
How was your experience with it?
I am not sure if the vibration of the phone itself is reduced and the Camera is protected, but the Smartphone Holder itself used to make a rattling sound, but that sound has disappeared, so I think the vibration is absorbed.
[Points to note]
The mounting position needs to be adjusted as it increases the bulk considerably.
How did it compare to other products?
I wanted to use DAYTONA's Smartphone Holder, so I didn't compare it to other products.
View detail
I lost it, so...
22.I lost my ClampSpacer for 2mm, so I bought Repair Parts.
Only Repair Parts can be purchased for fragile parts, so they can be used for a long time.
View detail
It can be used with a turnstile.
I bought this to attach my old Porch and Smartphone Case to my Scooter.
As others have stated in their reviews, it rotates when installing the Porch and other parts.
I solved the problem by adding a Nut to stop the loosening.
Because of its high quality, the appearance of the product without Porch and other products is not bad.
View detail
Easy to use
[How is it used?
I chose to install a new Smartphone Holder on my TouringMotorcycle and ultimately ended up with this product.
Anything as long as it's cheap!" I am very happy to be able to do this, And not too much of Plastic's cheap stuff, either." For me, I'm a bit of an either/or kind of guy. That's it! It seemed like a good idea.
Also, my phone has many buttons on the Right side, so I could not use the type that is inserted from the side, so I chose the type that is fixed at the four corners.
Was the one you received as per Image?
I chose Black and it was just like the Image.
How was your experience with it?
First of all, the Included Parts:are substantial for the price.
There is a diameter conversion rubberretc.Pattern and it is not difficult to install.
When the middle Button is pressed, the four corners are Fit to the phone.
Release is Quantity:Pair (for Left and Right) The only thing you need to do is to press the "+" and "-" prongs, so everything can be done with one hand while doing Gloves, which is easy.
[Points to note]
Make sure it is firmly secured before starting.
How did it compare to other products?
I had been using Chinese several hundred yen ones, but I felt they were well thought out with good strength and ease of use.
【Review】
I used to think that KaEdia was cheap or bad, but when I bought it this time, I got a good impression of Included Parts:, usability, etc.
As a smartphone mount, I have no complaints.
View detail
Fits: Others
Shock and Vibration Absorption
Installed on QuadLock.
Used in conjunction with Shock Absorption Damper.
Size is 22.2Φ and Body is quite soft.
The price is high, so I would like to buy 1 pc. for now to try it out.
View detail
![[Optional Accessory] Anti-Vibration Module](https://img.webike-cdn.net/catalogue/images/112586/34092_TS.jpg)
SP connect Anti-vibrationModule
I use an iPhone 12 and bought the anti-vibration because my Camera broke. It's been installed for about a week so it's not accurate yet,
I don't know, but for now Camera is usable.
It says it reduces vibration by 60%, but I don't know how much this is.
View detail
It holds the phone securely in place.
[How is it used?
I purchased this product to use my phone as Navigation in Touring.
Was the one you received as per Image?
The ball joint of the mount was smaller than I expected.
Was the installation difficult?
There are only two types of Spacer for Handlebar Mounting, 22.2mm and 25.4mm, and my Handlebar is 28.6mm, so I went to Home center and bought a 2mm thick Elastic band and inserted it between the Handlebar and Clamp. Without Spacer, it was just right because it is compatible with 32mm.
A Hexagonal Wrench was also included and was easy to install. However, the Ball joint does not have much operating range front to back, so once I tried driving with the phone attached, I loosened the Bolt on the Mount once and adjusted the angle.
How was your experience with it?
Driving on public roads, the phone was firmly secured and did not sway with the vibration of the Engine.
[Was there anything that disappointed you?
It would be nice if it moved back and forth a little more.
View detail
Modern necessities
I think Attachment is necessary in today's smartphone-essential world.
The clamp part is solid, so it seems unlikely to fall off while driving, but I am just a little worried about it digging into the Handlebar and scratching it.
It can be securely fastened to the Body even while still in the Smartphone Case.
There is also a locking mechanism so it won't rattle while driving, and it has an insurance band to prevent it from falling.
However, be careful not to use this band in the wrong position, as it can manipulate the volume button.
Vertical and horizontal rotation is also easy, but it is excellent because it does not turn on its own while driving.
It looks like you can choose with or without vibration control components, but I wondered … if it makes sense to go without.
They say that without vibration-damping components, the anti-shake function of the phone often breaks down! (According to a friend)
I decided to install it in the middle for visibility of the meter, but I think it would be better to install it a little closer to the left.
I will try various trial and error.
View detail
Easy to use
It is a replacement for DAYTONA's Smartphone Holder.
It is easy to install and easy to use.
Vibration absorbing Bumper was installed at the same time.
View detail
Simple and beautiful.
Simple and beautiful.
The finish is good and it blends in like OEM.
It is easy to install and remove the phone, yet there is no gapping or falling off. I think it is a well-made product.
I have been using it for Navigation with iPhoneSE2 for about 3 years. No particular negative effects on the phone.
I have heard that some models with a high-performance Camera may break due to SR vibration, so I haven't tried that one yet.
The price is not cheap, so the cost performance is not so bad.
View detail
Fits: YAMAHA MAJESTYS, YAMAHA Majesty S
It worked on my iPhone 15Pro.
[How is it used?
I was considering a Smartphone Holder to view Navigation on my BMW R100 Twin suspension.
Was the one you received as per Image?
It is easy to install and use, with One-touch to fix and remove the phone. It is intuitive and could be used without Stress.
Was the installation difficult?
Wiring around the Handlebar may be Large strange. The only thing to do is to wrap the included rubber parts around the handlebar, and then hook and fix it with a bracket.
I used DoctorRubber's Handlebar Grip Rubber as an anti-vibration measure. We recommend it as well!
https://www.webike.net/sd/25949395/
How was your experience with it?
It is easy to install and use, with One-touch to fix and remove the phone. It is intuitive and could be used without Stress.
To remove the phone, pull the red lever in front of the reverse side toward you.:Pair (for Left and Right) The claws of the "I" release.
[Included Parts:were they on?
All Included Parts:required for installation are provided.
View detail
Vibration Isolation Outclassing
A little soft, but firm and very good.
We will make it a good companion for future Touring.
View detail
Excellent workability
Best quality as Smartphone Holder. A product with no complaints in terms of retention, security, and workability. View detail
Better than the previous MODEL.
Purchased due to Motorcycle expansion.
It felt more solid (sturdy) than the previous MODEL.
Smartphone is also securely fixed, so you may not need Rubber's Belt?
Don't worry, even an amateur can install it easily.
View detail
Large texture
Size-wise, it's like a Large tree, but I think Hold is a good idea.
Good for single cylinder motorcycle as I also added vibration protection.
View detail
Smartphone Holder is the best!
The fit is so good that you don't feel the anxiety of saying your phone is going to fall off. View detail