Reviews
It was too difficult for me.
I had experience pasting automotive film in the past, so I bought it thinking it would work, but it turned out to be disastrous.
The shape is complex and cannot be aligned well with subtle curved surfaces at all.
Moreover, it is difficult to remove air bubbles because of the thickness of the ??Film, and it is stretched so much that air bubbles do not come out at all.
It is wiser to be honest and ask the PRO to do this.
Sorry, this is a bit of a whiney impresario. Yes, the product is solid and looks good.
View detail
Firm knee grip.
I was using KIJIMA's Tank Pad (208-006), but the surface was getting rough.
Replaced with EasyGrip Tank Pad.
PROSeries Black.
Since it was supposed to be for Circuit, I thought it would be better for other uses, but I bought it because I thought the finer grains would be less uncomfortable.
The location was at the bottom of the Tank and where the Side cover part fits.
I put it on this part with my own Seat.
result
There is no slippage at all, nor is there any unwanted snagging, allowing for a very firm knee grip.
View detail
scratch-resistant
It was put up to prevent Tank from being scratched. View detail
I knew it!
It is an unquestionable Grip feeling.
It increases stability.
View detail
Cut is inaccurate.
I don't need the spray bottle included, etc., so I want it to be cheaper and more accurate. View detail
Easier Knee grip
This will be a reReview.
Immediately after delivery, only the side cover was attached, but later the tank side was also attached because the legs hit the tank side when the vehicle body is supported by the outer legs with the ass shifted, such as when driving on a mountain pass.
The positioning was done without any particular instruction manual, and the position of the legs was determined by straddling the tank, making sure not to miss the point where the legs hit the tank, and fine-tuning the position so that the line of the tank would be consistent with the line of the tank.
As with the Side cover section, when attaching, peel off the backing paper gradually to prevent air bubbles from entering, and apply it from the center outward in a way that releases air.
Although I am rather clumsy, I think I was able to apply it reasonably neatly.
As a result of driving on the pass, the Tank was well supported during Cornering and had the expected effect.
Especially in the forward leaning posture of SS, it is somewhat easier to support the upper body by having a good knee grip.
As I wrote in my last Review, [Color] Even though it is called Clear, I am a little dissatisfied with the Cream coloring.
A little more transparency would be nice without destroying the design of the car body.
View detail
viscosity
When I remove the Cover during the next touring after applying the adhesive, the pad at the bottom is fluttering. Already no adhesion.
It was put on by a Shop Service person. I wouldn't write this kind of comment, but it's a pity that PRO put it on.
I'm wondering if I should buy the same item.
View detail
I have a good knee grip.
[How is it used?
Purchased because the tank was too large and difficult to grip by the knees.
I chose the Pro type because I thought it should look less lumpy.
Was the one you received as per Image?
I think it was as per Image.
I thought it would be like this since it is Rubber or Silicon.
Was the installation difficult?
A cleaning sheet before pasting is also included.
Size was also no problem, as it is dedicated to the car model.
How was your experience with it?
It is not rugged, but it does serve as a firm non-slip surface.
[Included Parts:were they on?
The cleaning sheet and Instruction Manual are included, but the Instruction Manual is only available in English version.
[Was there anything that disappointed you?
I think it is a little expensive, but I will use it for a long time, so it is OK.
View detail
Quality is better with Stomp Grip.
I had installed the Stomp Grip but the seat on the side cowl side was too small and didn't hit my knee area, so I left the Stomp Grip on the tank side as is and replaced it with the EasyGrip on the side cowl side. As other reviewers have said, the EasyGrip is a large size, and I am satisfied with its functionality, but the EasyGrip looks like it is cut out from a large Seat to fit the car model, but the StompGrip has no warts on the edges and is molded one by one, so the texture and appearance are parenthesis. The StompGrip has no warts on the edges and is molded one by one. It's a choice between functionality and appearance. View detail
Reliable EasyGrip
We used EasyGrip about 3-4 years ago when we switched from StompGrip.
Since then, EasyGrip has been my choice, and I personally think that EVOType has better gripping power than Stomp.
Recommended for people who drive on circuits and mountain passes, and for sports drivers.
View detail
It is a good item
[How is it used? It's been a month since I installed it on the Meter panel of my NINJAH2SXSE (2021 model).
Was the one you received as per Image? The size is perfect for the Meter screen. I was worried about damage to the screen since the Meter is an LCD panel, but I am now feeling more secure.
Was the installation difficult? It's easy. It is the same way as the film on a cell phone screen. A small amount of detergent was enclosed in the bottle to wet the adhesive surface during installation. I did not see any Instruction Manual. I diluted it and used it. I sprayed it on the adhesive surface and pushed out the water with the included spatula, which I rubbed lightly to avoid scratching the surface of the film. Moisture was absorbed with Tissue.
How was your experience with it? I have been using it for a month now and I have no problems. There are a few small bubbles left, but no problem in use.
[Accessories] A bottle containing a small amount of detergent and a spatula are included.
[Was there anything that disappointed you? Nothing in particular. It is just a Film, so the cosmetics are rather expensive (2 stars). The shape is perfect and even an amateur could apply it well, so I am satisfied (4 stars overall).
View detail
The shape doesn't fit.
The shape does not fit.
It looks like it, but no matter how you do it, the shape doesn't fit.
Therefore, dust accumulates there because some edges do not adhere closely to each other.
And it peels off from there.
Anyway, the shape doesn't fit.
View detail
There is also some gripe feeling.
Recently, SmallWound has become prominent on Tank!
I told myself not to worry about it because it was a training machine and I used it heavily, but I found an outlet product and stuck it on for prevention& protection.
The result was a Large success. The cut was quite precise, and by carefully removing air bubbles while adjusting the cut, I was able to achieve a generally clean finish.
Although it is not a GripType, it seems to have a non-slip effect and has some grippy feeling.
The work is to clean the surface thoroughly with Seat for removing oil from the attached kit, and then apply a liquid detergent diluted in the same way as for WindowFilm. (Container is also included.) Spray generously on the paste surface and Film and adjust the position.
The included spatula for pasting is just the right size and easy to use, but it seems to have two sides, so if you make a mistake, a wound will remain as shown in the image. (It is hard to see due to the reflection.)
Because of the complex shape of Z, we divided it into parts and removed air bubbles from the center outward.
To be sure, I left it for a day after the water dried to check the adhesion and took it for a test drive. There were no parts that were about to peel off, and the adhesion was firm, so there was probably no need to worry.
If it can be applied neatly, it will look good, and even slippery materials such as synthetic fibers can be used to hold the tank in place. (Not compared to GripType...)
The instruction manual is not included in the package, so please check the manual before preparation, and be prepared to work carefully and sparingly.
View detail
Knee grip is easier and upper body fatigue is reduced.
I was going to use a Knee Pad to prevent slipping because my body shape is such that the Knee Grip is located at the side cover area, and I had used a Stomp Grip on my previous car and had a good feeling about it. However, the EasyGrip was selected this time because the range of the pad in the side cover was too narrow and it was not in the position I wanted.
Purchased PRO from shape etc. (Circuit) and the color should not spoil the Design as much as possible. [Color] I chose Clear.
I had compared the images with those of the G model up to the 2011 model, and I thought that there would be no problem installing it on the 24 model, and I was right.
Since there is no Instruction Manual for installation, I could not figure out the correct position to put it, but I put it at the position shown in the picture based on the Seat, Cowl shape, and the knee position when straddling the seat, etc.
Since there are protrusions on the surface and the Side cover is also in a phase, it is Large strange to install to prevent air from entering.
I felt like I peeled off the protective Seat on the back side little by little and managed to stretch it by pressing it from the Center toward the outside.
Despite these difficulties, the difference in knee grip between with and without the pad is enormous. Without the pad, I had to press my ankle against the heel guard to support my body, but now I can support my body at two points, my knee and ankle, which considerably improves my sense of fatigue even after running the same distance.
Currently, only the side cover portion is attached, but we plan to attach the tank side portion as needed in the future.
The only complaint is, [Color] It's a bit like Cream, even though it's Clear.
further [Color] It would have been better if it was Clear.
View detail
I love it!
I am satisfied with the outstanding Hold performance and the Large change! View detail
Fit for purpose
I chose the clear film despite being put on a black tank. The manufacturer claims the pads will take on a slight blue colour against black background.. but it's not really noticeable for me. It did take a bit of effort to push the majority of air bubbles out during installation. The colour block on the tank is still nicely visible, so that's a bonus. Make sure you know where your knees tend to sit & move on the tank before fitting the pads & allow this to guide your fitting location on the tank. View detail
The price is reasonable and the effect is decent.
Each car is Exclusive Design, or the price is high.
However, considering the difficulty of installation and the effect after installation, it was a good purchase.
I think I did.
I have read in other reviews that the adhesion is weak.
If it is done, it will adhere properly to the tank and resin parts and is strong enough.
After installation, I drove the car and it was very easy to get a good grip on the knee.
Ride quality and operability have improved.
View detail
Prices are high for dedicated products.
[How is it used?
I used it for about 3 months. I am satisfied with the expected Grip effect.
Was the one you received as per Image?
I was torn between the EVO shape and the PRO shape, but I decided on the PRO one based on other people's impressions. I wanted to make the bumps less noticeable, and I also wanted to get the color of the car body. [Color] I chose Clear. A photo of the entire car body is attached for reference.
Was the installation difficult?
There may be some difficulty depending on the Tank shape of the vehicle. In my case, the tank shape has no gouges and is straightforward, so it was relatively easy. After temporarily attaching with paper tape, I peeled off half of the backing paper from the edge and patiently attached the tape. The first one was just a little off, but the second one seemed to grab the hang. The air bubbles definitely get in, but I think you can make it better by applying it little by little and getting used to it over and over again with your hands. (It will gap, so you have to pull it in the right direction little by little! Also, a rubber roller would be nice).
What is your experience and what is your disappointment?
Knee grip is easy. I am satisfied on that point, but there are two minus points:1. it seems to be a little aggressive on Jeans, and the fabric is a little fuzzy; 2. the price is too high; and 3.
A word to the manufacturer.
Please give me a few canned Sizes that I can use in Universal. Cut yourself.
View detail
Not slippery at all.
I would recommend this one, although the tank is slippery so I couldn't get a knee grip at all and was feeling a little stressed,
As soon as I put this product on, it stopped as if it was stuck and I was able to get a good knee grip! I was able to grip my knees with this product.
It is recommended because it stabilizes the driving.
View detail
The look and feel requires Zero preparedness.
The product is extremely cheap, and I thought it was a SiliconCoaster that you can buy at a 100-yen store. It was so solid that I thought it was a cross section of a fish cake, and there was no texturing process, etc.
Undoubtedly, it will make the installed vehicle look cheap.
I can honestly say that the texture and build quality are definitely not worth the price of the product.
If judged by product production Cost, it is clear from the appearance that the R&G company's product is definitely much more costly, and the dress-up satisfaction is higher.
As for the feeling of use, it shows an effect (high gripping force) that is commensurate with its material. In my case, I have a habit of sliding the product on the contact surface when I move my posture, so I prefer a slightly weaker grip like R&G's. However, R&G's support for GSX-8S is more effective (high grip strength) than R&G's for Tank side. I prefer the slightly weaker grip support force of R&G products, but the R&G product for GSX-8S has a pad on the tank side but no pad on the frame cover side (lower side), which is unfortunate.
Therefore, R&G tank grips are only used in very rare situations, such as when a turnaround of winding is necessary, when a high-speed corner is turned in, and when turning, and therefore, the support as a tank grip is not obtained. It is a mere decoration. (I am 176cm tall and have an 85cm inseam.) ) We would like to inform you that we had no choice but to purchase this product for this reason.
In addition to the above, care must be taken during installation. The included degreaser is extremely aggressive to the frame cover and will definitely discolor the resin parts to a whiteish color. However, for those who focus on keeping the body clean and well-maintained, it is likely to receive a very Large mental Damage.
For this reason, we can say that if you are nervous or are also considering a Case to remove SiliconPad, you should be careful about using the supplied degreaser.
View detail