Reviews
Only special tools can do this.
In order to revive the immobilized YamahaRZ350, I set out to overhaul it, but the Pulley remover I had on hand was not enough to get the job done. I knew the power of the special tool from my previous experience of removing a bicycle without a co-sauce, so I searched for it and found this YamahaOEM tool at a reasonable price. The feeling is that there is no rattling, and I can put a lot of power into it. However, it didn't shake, probably because it was an old motorcycle, so I applied more force with the Expander and was able to remove it safely. There was no sign of overworking the tool, and I am glad I purchased it. View detail
![Service Manual [Complete Version]](https://img.webike-cdn.net/catalogue/images/111384/service_manual_yamaha_TS.jpg)
Purchased to better understand my car.
As expected, I cannot do the work up to engine overhaul, but it is useful for daily inspections.
It's a great read.
I was a little surprised that the current Service manual didn't explain it with pictures, but I guess Illustration is easier to read.
View detail
![YX-6 ZENITH Graphic [Zenith Graphic] Helmet](https://img.webike-cdn.net/catalogue/images/73802/907911788L00_TS.jpg)
Goggles are good to use.
Usually SHOEI and ARAI use L Size and THOR uses XL.
I bought XL but Cheek pad was too tight so I bought Cheek padXLW and installed it.
→The result is a Size/Fit feel similar to ARAI's XL.
Goggles are 100% Accuri2 (image) The Racecraft2 is delicate because the nose guard interferes with it.
With Goggles, I can hear the driving noise, and with Shield, it's nice because it's very sound insulated.
Visor is too small to be effective in city driving. Styling is more important than function.
View detail
![SF-7II ZENITH Lea Winds [Zenith Lea Winds].](https://img.webike-cdn.net/catalogue/images/110508/907913258F00_TS.jpg)
Using Zenith:・・・・
Was the one you received as per Image?
It was exactly as shown in the Image and was well made.
I am not a cheap or bad person.
[How did you feel about the Fit?
I chose SizeFree, but it's not too large.
It can be used normally, it's just that it's only for city driving, PetitTwo should be considered as the way forward.
How was your experience with it?
The feel is good, it is light and the basic performance is TIGHTLY.
What are the specifications of the product?
Smoke Shield (sold separately) is used.
There are no other special functions, and it is Simple.
[Was there anything that disappointed you?
Nothing in particular. Frankly, I feel better because I had no expectations at all.
How did it compare to other products?
No comparison.
It was purchased for 125?, so it was a cosmetic choice.
Since my Motorcycle is a Yamaha, I inevitably chose a Yamaha product.
I think the performance is sufficient for my needs, although the Fit feeling etc. is not bad,
Overall, it is loose, so it is not suitable for long distances. It is considered to be only for short distances.
I think it is necessary and sufficient.
View detail
Fits: YAMAHA BirdCity125, YAMAHA BirdCity155, YAMAHA BirdCity125 A/C
It is easy to cover because it is a dedicated product.
Used on BirdCity125 with Rear box.
I was parked in the open air in Space facing the driveway where my house is located, and one day when I went to get in, I saw a flyer at Handlebar that said I would buy it, and I also bought it for security purposes.
I was looking for a cheaper Universal Product, but since I have a Rear Box and the BirdCity has a wide front width, I was not sure if the Universal Product would fit when I put it on, so I ended up settling for this product, which is a dedicated product. I was looking for a Rear box.
I had already used Y's Gear's E Type on another motorcycle, so I knew about the fabric to some extent, but the front side is made of fabric with color, and there are slits on the front and back that can be used to pass locks, etc. It is still a very easy-to-use cover.
Since it is for full equipment, I am assuming that a High Screen will be installed, but my BirdCity has a screen that is not that long, even though it is an Other Brand Product, so when I put it on, the screen portion is too much.
It might be OK to fasten it with a clothespin, but it would have been better if the Cover had a Velcro tape or something to fasten it shortly.
I also personally like to use a long wire lock to reduce flapping of the Cover to reduce the quantity.:Pair (for Left and Right) I was a little disappointed that the Slit through the lock on the Front side is only for the Left front wheel, although I wanted to pass the front wheel of the
Also, dust and sand may come in depending on the wind direction due to the ventilation on the side.
But still, it is better than the previous open-air parking, and it is no longer dirty every time I look at it.
As for durability, I am not sure yet, but it is easy to put on, so I think this is the one I will buy next time.
View detail
Fits: YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP
parts shortage
There were no defects in the product.
However, parts were missing.
I think I am at fault for taking so long to open the order and for starting without NumberRinging all the parts. I ordered only Grommet today.
It is impossible to install until the part arrives, so it is not possible to put it on.
If you are considering purchasing, please make sure to check the part.
View detail
Excellent DoubleGuard in all areas.
Was the one you received as per Image?
The color and shape are as shown in the Image, but it felt surprisingly thin.
It is a Y's Gear product, but there is no noticeable Logo, so I personally rate that highly as well.
I don't like the ones with the large manufacturer logo on the back.
[How did you feel about the Fit?
I am 181cm tall and weigh just under 70km and purchased a 3L, which is slightly roomy over my regular clothes.
Rain pants can be worn with Over Pants underneath.
It is very helpful in the winter because I like to layer my clothes.
In addition, the hems are slightly longer, so they will not slip up in the riding position and get wet inside.
How was your experience with it?
Used the day after purchase as it rained immediately (slightly light rain).
It is a 30km one way commute and was very comfortable with no flooding like the previous Rain Wear.
I commute by motorcycle even in heavy rain, so I have high expectations for the water resistance in that area.
I chose the color Orange, and it has good visibility and looks good even in dimly lit rainy weather.
The rest of the DoubleGuard in various locations is excellent.
SleeveDoubleGuard, in particular, shuts out water from Gloves.
No unpleasant wetting.
WaistDoubleGuard is good because it has a good fit around the stomach and prevents flooding.
Now it's just a matter of how many years they will work hard....
[Was there anything that disappointed you?
Nothing in particular so far.
How did it compare to other products?
I have been using Rain Wear made in Thailand all this time.
After about a year and a half, the crotch area became heavily flooded and I was quite disappointed and purchased this product.
I was introduced to this product by a friend who has purchased Repeat many times, and I expect it to be durable.
View detail
Side case tracer 9gt
It's price for one pair and complete bracket It's price for one pair and complete bracket It's price for one pair and complete bracket It's price for one pair and complete bracket It's price for one pair and complete bracket t's price for one pair and complete bracket It's price for one pair and complete bracket It's price for one pair and complete bracket It's price for one pair and complete bracket It's price for one pair and complete bracket View detail
![[Yamaha Stock] Brembo Radial Brake Master Cylinder ASSY](https://img.webike-cdn.net/catalogue/webike_images/0000/0000/0289/24980842_20211228131537152_TS.jpg)
Fits: YAMAHA YZF-R7
It is a MASTER with excellent cost performance!
[How is it used?
This will be an imprementation with 100% Circuit driving.
Was the one you received as per Image?
Yes.
As shown in the photo, it arrives in a box in Assembly condition.
Was the installation difficult?
If you are able to bleed the air out of the Brake, it is an easy category.
For workability, pull out the Fluid from the Reserver tank to the banjo bolt of the MASTER.
Next, remove the banjo bolt from the OEMMASTER, and then remove and install the MASTERBody in the reverse order.
How was your experience with it?
This time, we replaced the OEM Nisshin Radial master from YZF-R1M, and the fee rings are excellent.
The piston diameter is the same (16mm), but the lever ratio is different, making it slightly stroker. This is very effective in circuit driving, and the BrakeRelease side has a lot of Strokes, which makes control easier. I think it is better than RCSMASTER of brembo. The R7OEMMASTER is 16mm, so it is theoretically more on the Stroke side. The closest thing to a replacement Brembo master is the Racing master 16x18, but since you can get one for about half the price, this master is a very cost-effective option. Moreover, since the banjo is not located on the bottom as usual but on the side, it is highly possible to use the OEM hose. In fact, again, the Banjo bolt and Hose use the OEM as is. However, one thing to note is that brembo usually has a bolt pitch of 1.00mm, but this one has a bolt pitch of 1.25mm. Therefore, if your car is equipped with the OEM Brembo master, the pitch may not match.
[Included Parts:were they on?
There is no particular Included Parts:as it arrives in Assembly condition.
[Was there anything that disappointed you?
None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
Two separate banjo bolt Gaskets are required for installation.
Others are basically Bolt On. The hose from the reservoir tank to the MASTER is a transplant from the OEM Nisshin MASTER, because the length and bending angle of the R7 hose are not the same. The hose here, as well as the banjo bolt pitch, has a different diameter nipple than a normal brembo.
Finally, if you are riding a YZF-R1/M and suffering from the OEM patched fee rings, I highly recommend this MASTER. It is the most cost-effective solution for the smallest cost and the largest effect. In other words, Demerit is Zero.
View detail
It is safe if you have it.
I feel like I would buy Motorcycle if I bought it.
Every time I bought a motorcycle, I got the Service Manual and PartsManual.
This is especially necessary for those who have older motorcycles and do their own maintenance!
A service manual would be perfect.
It is very easy to read, and the exploded view allows me to accurately trace the OEM parts number, which is very useful for ordering parts.
I feel like I bought it before Motorcycle, but … it's ok. I have already decided which Motorcycle to buy.
Oh, it has nothing to do with people who throw everything to Motorcycle shops.
More and more people don't even change the oil themselves anymore.
View detail
Quality that only an OEM can provide
Since we put a cover on the body of the car, there were many times when the Mirror got caught on the cover and tore the cover...
It was difficult to cover the Cover with the protruding Mirror.
However, it is troublesome to remove Mirror each time. 。
OEM Flexible Bracket was purchased.
I used to use another company's product and liked it because of the range of motion, but the vibration ruined it quickly in the past.
I was skeptical, but I thought OEM would be large and sturdy, and the bracket was thick and looked sturdy, so I bought the YAMAHAOEM one. 。
Flexible Bracket
Flexible Bracket is not the type that can be folded down after installation, but the type that can be rotated back and forth freely. 。
YAMAHAOEM, Y's Gear's Flexible Bracket is
There are 3 types.
A Type H:115mm×W:100mm
B Type H:100mm×W:85mm
C Type H:75mm×W:65mm
I chose C Type because I want to show Refreshing around Handlebar.
However, if the vehicle has a screen such as SS or Scooter, the bracket may interfere with the screen, and it is not suitable for vehicles such as Separate Handlebars where the vibration of the vehicle body comes directly to the bracket.
after replacement
[Good point]
◎Mirror can be rotated and folded, making it easier to cover.
It can be neatly stored in→Cover.
◎Even when parking SPACE is narrow, it is possible to narrow the width of the car as much as possible.
◎Bracket is thicker and more rigid, making it resistant to vibration and less prone to Mirror shake. ◎Bracket is thicker and more rigid, so it is resistant to vibration and does not feel the shaking of Mirror.
◎Of course, Japanese Vehicle Inspection Correspondence.
[Bad point]
◎Maybe it is the way the Bracket is made, but the Mirror is more inward-looking, so visibility is reduced. ◎Bracket construction or Mirror is more inward, so visibility will be reduced.
◎Installation and adjustment can be time-consuming due to the many moving parts (laughs).
◎They are resistant to vibration, but because of the wide range of motion, the angles will Gap slightly if left unattended. →SmallAdjust frequently.
There are good parts and bad parts.
There is no problem at all for car inspection. 。
It would be better to use it with your own fine-tuning.
There are similar products even if they are not OEM. The point to pay attention to is the thickness of the base of the bracket. The thicker the bracket, the longer it will last.
View detail
High price, but self-sufficiency in the name of OEM Product
I considered purchasing a Chinese product, but I still thought it was tacky, so I purchased an OEM Product.
Super careful packaging and the color is perfect!
Includes parts for R1, R6, and R7 installation and Instruction Manual
Bolt on installation.
It is necessary to put Hexagonal Wrench in Walletetc. because it is not possible to access to the on-board tools with the key.
View detail
To my friend's Motorcycle.
Ordered for installation on a friend's Motorcycle.
The installation went without any problems.
I was thinking that the tools would be a Drill and a Hole saw.
Hole saws are expensive to buy new, so if you don't have one, you should ask a Motorcycle shop for one.
View detail
OEMSticker
It is a YAMAHALogo sticker.
However, the image is pure White, but it looked slightly Cream-colored.
View detail
Purchased without hesitation!
Purchased to add a top box.
Since we plan to install another company's top box, we could have originally purchased another company's inexpensive rear carrier, but we chose this one because of its heavy construction and design. However, considering that the Plate (sold separately) must also be purchased, the price is higher, and the cost performance is not as good as I would have liked.
View detail
For ETCBody protection
I had it installed at the shop at the same time as the ETCSetup and Body installation prior to delivery.
I thought the OEMOption would be sufficient for the quality of the product.
I am satisfied that it fits under Seat and Beauty.
View detail
Fits: YAMAHA YZF-R25, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA MT-09, YAMAHA MT-09, YAMAHA XSR900, Others , YAMAHA YZF-R3, YAMAHA YZF-R25, YAMAHA XSR900, YAMAHA SCR950, YAMAHA NIKEN, YAMAHA NIKEN GT, YAMAHA TRACER GT, YAMAHA MT-09, YAMAHA MT-07, YAMAHA MT-03, YAMAHA XMAX, YAMAHA YZF-R15, YAMAHA YZF-R125
Y'S GEAR ETC Pouch3
The double-sided tape is used to attach the Magic tape, which has a very good adhesive. Unfortunately, the hole for the WiringCable is too large, so it is best to install the WiringCable together with the ETC when installing the ETC. View detail
For Grip heater
I bought this for my Grip heater and it is easy to install as long as you can remove the front cowl. I am satisfied with it. View detail
Xsr900 oem frame slider
Item all in perfect condition. View detail
It's a must if you want to maintain it.
I purchased this product to replace Handlebar.
Since I am still planning to replace the exhaust pipe and do some brake maintenance, I thought it was essential if I want to play around with it, as it provides necessary information such as tightening torque and assembly order.
View detail