Reviews
Soft, flexible and easy to use!
The material is soft and easy to put in and out of the wiring. It is also resistant to deterioration even when exposed to ultraviolet rays! It is easy to use, durable and Large satisfaction! View detail
Hard but strong!
It has a slit in it and you put the wiring inside, but it's just too hard! It is not flexible, so it is hard to put in and take out the wiring, and it is not easy to handle! However, this is one of its strong points and its durability is outstanding! I mainly use it to put together the ETC and sub-computer wiring inside the motorcycle! It is a recommendation because it is very useful if used in the right place at the right time! View detail
Ideal for Repair
I purchased this product to refresh a MotorcycleParts terminal cover that was given to me by a friend because it was yellowish and deteriorated. I recommend periodic replacement of the cover because many people use the cover for many years without replacing it, causing it to become damaged and short! View detail
The quality is good and can be used without problems!
Active (ACTIVE) I purchased this product for Repair because I damaged the Electro Tap of my company's LEDNumberSIDEBlinker. It works fine and the quality is good! As with all Electro Tap products, it is not waterproof at all, so please use it in a place where it will not be exposed to water! View detail
Particularly good for places where there is a lot of ROSS
Reusable Tie Wrap for easy removal.
It is especially effective for parts that are frequently removed and attached. It is a little thicker than regular tie wrap, so be careful, but I use it to tie parts that are often removed when disassembling.
Off-road motorcycles are especially used for this purpose.
The thicker the wire, the sturdier it is, so there is no need to worry too much. However, if you cut the extra length, you can only use the same length or a shorter portion.
View detail
The ability to release as intended is still an advantage.
Vehicles used in Races and competitions are often cleared.
If Tie Wrap can be Released in such cases, it can be used once more.
This is important.
But it's not cosmetic. Definitely.
But they are SDGs. Because they can be reused.
Even if you are not a "good" person, you don't have to use a nipper to cut it, so you don't have to choose a place for it. It is surprisingly possible even in a gap where tools cannot fit.
View detail
The construction is delicate.
[How is it used?
Used for VRDBrake master in GALE SPEED
I purchased this because there is nothing else available.
Just tie it on as it is a regular 2Cable compatible.
Was the one you received as per Image?
As you can imagine.
Purchased with MASTER.
Was the installation difficult?
It's not hard, but tying Cable together is a bit complicated.
How was your experience with it?
It's working normally.
[Included Parts:were they on?
Instruction Manual included
[Was there anything that disappointed you?
Large sturdy at the moment, although it feels fragile.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I saw that it rusts easily, but I don't know.
View detail
Purchased for Tachometer installation!
With the installation of the Tachometer, we chose the Wiring processed one so that we can use it without any hassle when extracting the electric Pulse!
We are happy to offer a wide variety of Bullet Terminal!
View detail
For Wiring processing
Purchased for Wiring process. No problem. View detail
For Wiring processing
Purchased for use in Wiring process. No problem. View detail
Fits: KAWASAKI Ninja 250
Used on ninja250
I purchased two of these for use on my ninja250.
The Rubber cap is quite solid and seems to be waterproof, but I think it is better to treat the Harness with insulated Tapeetc.
View detail
Fits: KAWASAKI Ninja H2 SX SE, KAWASAKI VERSYS1000 SE, KAWASAKI Ninja[Ninja ] H2 SE, KAWASAKI Ninja[Ninja ] H2 SE+, KAWASAKI Ninja[Ninja ] H2 SX, KAWASAKI Ninja 1000, KAWASAKI Ninja 1000SX, KAWASAKI Ninja 1000, KAWASAKI VERSYS 1000 SE
One key system
[How is it used? 24-hour (e.g. observation, operation (of a machine), care (of patient))
Was the one you received as per Image? Yes
Was the installation difficult? difficult (e.g. customer, guest, child)
How was your experience with it? as expected (as opposed to expected)
[Included Parts:were they on? None
[Was there anything that disappointed you? None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
I like the stuff, but I didn't need it for crf250rally….
Purchased when replacing crf250rallyBlinker
Rear blinkerMinus side connector is not the same shape as the light blue or Orange one, so I thought I could use it on the Plus side,
The Minus side is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Expected
I was concerned about the dim glow of the post-attached (added) Indicator, so I decided to add a rectification Diode.
When I replaced the meter with a Universal one this summer, there was only one warning lamp, so I purchased an LED lamp from KIJIMA and added an Indicator Lamp, but the Red Lamp was glowing dimly. Well, if I didn't care about it, it would have been fine, so I didn't touch it until now, but recently, I decided to add a rectifying diode while reviewing the wiring.
After following the instructions and incorporating it into Wiring, I was able to eliminate the blurriness of the Lamp, but Wiring became so long that it was difficult to store it.
View detail
Used when replacing crf250rallyRear blinker
Used when replacing crf250rallyBlinker
LeftBlinker is Orange.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Used for crf250rallyRear blinker
Used when replacing crf250rallyBlinker
RightBlinker is Blue.
However, the Minus-side Connector is not sold at KITACOConvenienceParts, so it must be purchased at another electrical shop.
View detail
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R SE, KAWASAKI NINJA2 Helmet50R EX250P
I don't want to hurt OEMHarness.
I want to use CouplerON as much as possible, because cutting OEM harnesses is a source of trouble.
Considering the price and construction, this is a very expensive product, but the advantage is that it does not damage the OEM's harness.
Installation is easy. In the case of the Ninja ZX-25R, remove the DummyCoupler and insert this product into the DummyCoupler.
The original DummyCoupler is simply attached to the Coupler on the other side of this product.
After installation, an energization test was also conducted.
Checked with Tester and no problem.
View detail
Good product but paid import tax.
The product appears original and in good condition. It's a shame, however, that having paid import taxes nullified the lower price of the item. so waiting 15 days for shipping is not worth it if you have to pay the same price as in Italy, which arrives the next day. -------------------------------------------------- -------- The product is original and in good condition. Too bad that the fact of having paid the import fees has frustrated the lower price of the article. So having waited 15 days of shipping is not convenient if you have to pay for the same price as Italy, which arrives the next day. Powered by Google Translator View detail
The texture of pressing the Switch is great.
Since the NSR50 does not have the OEM Kill switch, I installed the Kill switch on the Minus side of the Ignition coil. The quality of pressing the switch is much better than the cheap ones made by Chinese manufacturers! The only thing is that the price is a little bit expensive for MinusPoint. View detail
I used it for VRD.
[How is it used?
I purchased this along with the VRD.
You can't use this without it, can you? Necessities
I don't need another Race car.
Was the one you received as per Image?
It's just as I imagined.
It is packaged in a small but solid box.
That's what GALE SPEED is all about. Even the cheapest items are well packaged and quality is important to me.
Was the installation difficult?
Bolt1 pc so it was not particularly difficult.
Wiring requires a little ingenuity, but it can be done if you have the time.
How was your experience with it?
As you can imagine, it responds normally.
[Included Parts:were they on?
The instruction manual is attached, but it is easy to understand even if you do not read it.
[Was there anything that disappointed you?
Nothing in particular.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
I have to buy it because it is a necessary item. The price is reasonable, so I think it's okay.
View detail