Reviews
easy to read
I installed the mirror on my MONKEY125 because it was hard to see. The rearward view is not only easier but also extended to the front, so I can use it very comfortably with less eye movement. View detail
The quality of modeling is rather good.
Material:Plastic and relatively well formed, there was no BALIetc.
Female thread side has embedded Nut for secure installation.
Well, it's still a bit expensive there, so I hope it's a bit cheaper.
View detail
Purchased for installation of Kellerman Barrett Ato
[How is it used?
We put a Stainless Steel Gold fold and Spacer on the +Screw of the Switch box, and then attached a M5 10mm OD Pipe nut to the bottom of the box with an M5 ultra-low cap bolt, and then attached this Kellerman Universal Bracket.
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
It is easy because all we had to do was loosen the screws, fix the bracket to the pipe nut, and tighten the screws. It was firmly fixed.
How was your experience with it?
I have not yet purchased and installed the Barrett Ato, so I can't make an overall judgment, but I am satisfied that I was able to secure the Bracket as shown in the Image. I would like to purchase Barrett Ato as soon as I have the budget and am ready to do so.
[Included Parts:were they on?
Nothing was missing regarding Included Parts:, such as M6Spacer or Screws.
[Was there anything that disappointed you?
I am dissatisfied with the price. I think it is a little too expensive, but it is an overseas Manufacture, so it can't be helped.
View detail
Thanks to this, Shark mirror5 was installed in SUPER BOLDOR.
This time, I don't like the snail-like cowl mirror of CB400SB, so I decided to replace it with a handle mirror like Naked motorcycle.
So, first of all, which mirror would suit CB400SB the best? After much agonizing, I finally decided on the Shark mirror5 from Tanax. I had a hard time because the price was too expensive even though it was only a mirror, and I had a hard time here, too. (Sorry, it was much cheaper than Webike.)
Finally, I tried to install it, but it hit the cowl when I tried to put it on normally. I almost lost my mind, but since I had bought an expensive Mirror, I decided to go ahead and buy an OffsetHolder-45 (which was also too expensive!). In desperation, I decided to use Quantity:2pc. Set was bought, and Challenge was made to install it again.
As a result, thanks to this OffsetHolder, I was able to install it without hitting Cowl. It is like the OffsetHolder is attached to the original Mirror as well, so the Quantity:2pc. It looks like you are attaching OffsetHolder of Set, but it is attached in a nice way.
There are two reasons why we chose four pieces:One is to fasten iron to iron with bolt so that it does not slip, and the other is to use something like genuine leather or rubber to hold the bolt in place.:I wish it had been attached as a set, and the price is too high. However, I think the precision is fine and the construction is perfect. And since they are made by TANA-X, I don't think there will be any problem at all.
I have also tried to see if it would move with vibration after installation, but so far there seems to be no problem.
Personally, I think it turned out really cool. By the way, I spent a lot of money on MORIWAKI products to cover the hole in the cowl mirror. (I was already in a state of desperation.)
View detail
TANAX OFFSET HOLDER 45
Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the side mirror visibility. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. -------------------------------------------------- -------- Thank you so much for the quality and delivery. After the release of the new Monkey 125, it seems that this part is the part that can be used to counteract the extreme vulnerability related to the view of the side mirror. Due to the recommendation from other Monkey users, I will purchase it without hesitation and use it well. Powered by Google Translator View detail
Not very good quality.
HURRICANEClamp Bar
Item Number ： HU1035B
For YZF-R25
This is a type of handlebar with a fixed bolt to be installed. The supplied bolt and Spacer collar are not strong enough, so we replaced them. The length of the bar is shorter and more compact than other manufacturers.
View detail
Good for dress-up use rather than functional use!
Normally I could only let go of my Left hand when I was tired, but thanks to these Parts, I can also let go of my Right hand? I can also let go of my Right hand thanks to these Parts.
SpeedQuantity:Set requires hang, but you will get used to it.
Parenthesis is good just by putting it on. (Lol)
View detail
Fits: KAWASAKI Ninja 250R, KAWASAKI Ninja 250R, KAWASAKI Ninja 250R, KAWASAKI Ninja 250R, KAWASAKI Ninja 250R, KAWASAKI Ninja 250R, KAWASAKI Ninja 250, KAWASAKI Ninja 250, KAWASAKI Ninja 250, KAWASAKI Ninja 250, KAWASAKI Ninja 250, KAWASAKI Ninja 250R
Used for 250DUKE
It is sold for NINJA2 Helmet50, so I bought it for use on 250DUKE at my own risk.
When replacing, there was some interference with the Handlebar Clamp, it was hard, and the Socket size of 22mm and 24mm were required.
View detail
Large change in installation work
If you remove the handlebar cover of the scooter, a hole will be made there, and you just want to hide it.
I happened to have another job to replace the handlebar, so I worked on it in conjunction with that. In addition, there is nothing to hold the parts in place, so you have to use gold glue to fix the handles in place.
If you are not confident if you want to replace it, I suggest you ask Shop to do so.
View detail
Fits: YAMAHA TZR50, KAWASAKI ZEPHYR750, HONDA NSR50, HONDA NS-1, HONDA CB400SF, KAWASAKI ZEPHYR400, YAMAHA XJR400, YAMAHA RZ50, HONDA NSR250
One point custom
Purchased for One point custom color insert on the body of the car.
Each color is available so you can match it to your taste.
Clutch adjustment is easier because the rotating part is easier to turn.
View detail
Buy 2, guys
You're purchasing a set of ONE unit. I made a mistake buying only one thinking it comes as a set of 2 units. Don't make the same mistake as I did. As for the product itself, no complaints - it's sturdy and good-looking. View detail
By Motorcycle!
I use it instead of the cruiser, and it has been working fine on my CB1300SF, although it has loosened a little due to vibration. I am afraid that it might break because it opens its mouth during installation. It seems to relieve my shoulder stiffness since I don't have to keep twisting the Axel while driving. View detail
For Smartphone Holder
The Clamp is very useful for my SuCUB, because I have to tighten the Clamp to the Mirror and then attach the Smartphone Holder. If the Clamp is facing the wrong way, your head will be in a state of a ring of wisdom, so please check carefully before purchasing. View detail
Best product!
I ride a current Z400.
Before installing this product, I could not even tell if there was a vehicle behind me, but after installation, I can see it differently and I am satisfied with Large.
If the price were a little lower, it would be a perfect score.
View detail
If it is a bit cheaper
It is a must have product to replace a different handlebar diameter, but a lower price tag would be better.
Also, if you could include a thin double-sided tape, it would make positioning easier.
View detail
relief from a worry
I bought this for my CT125 because the LeftMirror is in a strange place and it was hard to see the back of the car.
I am happy with this Parts and it is much easier to see.
I was torn between 30mm and 45mm, but the 45mm is just right.
View detail
Fits: YAMAHA TZR50, HONDA NSR250, YAMAHA XJR400, YAMAHA RZ50, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, HONDA NSR50, HONDA CB400SF, HONDA NS-1
Gold's Clutch adjusterZ125pro
The Bolt is a little longer than OEM, but it came on with no problem at all. If you are considering this, please do so at your own risk.
[How is it used? Town ride
Was the one you received as per Image? Yes.
Was the installation difficult? Easy if you can lubricate the Clutch Wire
How was your experience with it? I think it has quite a dress-up effect.
[Included Parts:were they on? None
[Was there anything that disappointed you? None
Other items that would be helpful
Just work together when lubricating the installation points and hang/clutch wires.
Availability and clarity of Instruction Manual/A piece of paper is included, but it is a reminder to have it properly installed by a skilled contractor. This is fine, since the person who intends to install such a component does not need instructions for installation or use.
Notes/Nothing in particular.
Items to buy together/None in particular
Opinions and requests for Manufacturer/Good enough product.
View detail
Fits: HONDA CT125CT110 HUNTER CUB, HONDA glom, HONDA MONKEY125, HONDA DAX125, HONDA CB250R
Bolts are ….
The quality is fine, but how much better it would have been if the Bolts were Black!
I was so focused on the features that I didn't pay attention to the coloring, which I thought was a mistake.
View detail
Fits: HONDA NC750X, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR
Clamp set for Attachment Cross Bar
This product is listed in Honda's OEMAttachmentCatalogue and is installed in combination with the Shaft for AttachmentCross Bar.
Current NC750X (from 2021) I purchased this product because the OEM Knuckle guard is attached to the Handlebar Brace, and I thought it would not be possible to install the Handlebar Brace with a regular Handlebar Brace Clamp because of the Cable clip in the mounting position. This product has a thin wall so the cable clip can be easily fended off and installed.
Since the standard outer diameter of 22.2mm can be used for installation, it can be used for other purposes in addition to handlebars, depending on the ingenuity of the user.
I wish they were the same color because the Bolt and Washer are Silver and the color looks floaty lol.
View detail
Fits: HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA NC750X, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP
Shaft for Attachment Cross Bar
This product is listed in Honda's OEMAttachmentCatalogue and is to be installed in combination with the AttachmentCross Bar Clamp set.
The outer diameter is 22.2mm, the same as a standard handlebar, so attachments can be attached to the handlebar.
Current NC750X (from 2021) This product could be installed with a pre-2021 OEMOption Knuckle guard that does not have an Option setting on the
I do not think it will play the same role as the Handlebar Brace, but it will serve well enough to attach other attachments.
View detail