Reviews
usually
Installed on HURRICANE's Duralumin Pipe Handlebar.
It is a very ordinary Bar end cap, but I think it is a nice slit in it.
Rubbers for inner diameters from 14mm and 18mm are included.
View detail
Reasonable vibration reduction
Vibration is an inseparable fate of air-cooled single-cylinder engines.
It can be seen as a taste, but when driving for a long time or revving the engine to high RPMs, the vibration can be a painful experience (laugh).
I thought that since ESTRELLA is a 250, the vibration would not be like that, but the vibration was quite strong (laughs).
I thought it was time to take action, so I considered introducing Handlebar Weight.
Handlebar Weight Type ‥
Pierced Type and Closed End.
The use of a Pierced Type→Handlebar Weight to embed a weight in the handlebar to enable vibration reduction. 。 Type combined with additional Bar end weight.
Closed End→Handlebar Weight is placed inside the handlebar to reduce vibration.
→ESTRELLA is here.
Effect of Handlebar Weight ‥
○ Reduction of hand numbness due to vibration and prevention of fatigue.
○ Effective in preventing devices around Mirror and Handlebar from falling due to shaking or vibrations.
→ Vibration increases when you turn it up to high RPM, Mirror and others also shudder (lol).
[Notes] ‥
Note that if the grips are closed end, the value will change if the grips are cut and a new bar end weight is attached.
* Vehicles of 251cc and above must not exceed ±20mm in width.
That's when I came up with an idea☆ (laughs).
If the InnerBalancer and Bar End are one piece, then
I thought it would be rational to have a complete vibration control system (laugh) &arrarr; I mean, let's make it a Pierced Type!
So I bought this one.
*Note that the Handlebar internal diameter is different for each car model, so please check!
Procedure
Cut the edge of the grip section with Cutteretc.
(2) Cut the Axel side, Grip and the edge of the middle Throttle cone.
Even if it cannot be done neatly, it does not matter because the Bar End will eventually be closed.
(iii) Mounting.
...too easy (laughs)
[Effect]
◎Idling has clearly reduced vibration since the time of Idling.
◎Even when running at high rpm, vibration is reduced, so I am less tired!
◎Handlebar itself has become heavier, which has also increased straight line stability.
◎Parenthesis good to look at too (lol) *Personal differences.
I don't think there is anything bad about it, but if I had to say one thing...
If you are going to put this on, it would be better to choose Pierced Type Grip itself, because it is an act of reducing the durability of the Grip itself.
I had wondered whether it would be a good idea to add weight to a motorcycle, which is originally light in weight, but I now realize that there is merit in reducing vibration and improving handling stability.
If you drive an air-cooled single-cylinder slowly, even the vibration is idyllic or leisurely and comfortable, isn't it?
However, when driving a long distance, such as for a long-distance trip, the vibration that was supposed to be pleasant sometimes becomes painful.
Adding weight to the handlebar and doing other little things can have various positive effects, so I would like to recommend this to anyone who is concerned about vibration, regardless of car type.
For vehicles 251cc or larger, there is a vehicle inspection requirement, so it would be good to pay attention to the handlebar width.
View detail
Fits: YAMAHA YZF-R6, YAMAHA FZ8, YAMAHA YZF-R1, YAMAHA FJR1300
First replacement from NORMAL!
I bought it in Black
It is a very good product with good texture and Standard.
The Bolt on the Axel side was too long,
I purchased a Bolt about 10mm shorter and installed it.
Clutch Side is installed without Spacer.
View detail
Fits: HONDA CB1000R, HONDA CB1100, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR600RR, HONDA CB1300 SF, HONDA CB1300SUPER BOLDOR, HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
Solid impression
I chose this one because I like TSR and I don't like more colors. it is not as flashy as Color Anodized Aluminum, but it has a solid look that I like. The texture is also good.
It seems to be slightly heavier than the OEM, but not enough to realize the effect of vibration reduction.
Installation is really easy, just remove and replace. If you do not have it, please be careful.
View detail
Standard products for vibration control
Purchased as required due to change from OEM Handlebar.
Vibration is considerably reduced because of the Weight both inside the Handlebar and at the Bar End.
The longer the range of the product, the more effective it is.
Installation is also easy for beginner DIYers as only one screw is needed.
View detail
Fits: HONDA FORZA, SUZUKI GSX1400, SUZUKI GSX1300R, SUZUKI GSX-S750, SUZUKI GSR750, HONDA PCX150, HONDA PCX150, HONDA PCX125, HONDA PCX125, HONDA NM-4, HONDA NC750S, HONDA NC700X, HONDA NC700S, HONDA CBR650F, HONDA CBR1000RR, HONDA CB650F, HONDA CB400SF, HONDA CB400SB, HONDA CB250R, HONDA HORNET900
Too big?
Too much presence in the smallest groms.
But when it runs, the Handlebar Chatter is gone.
I feel more secure while driving.
View detail
Fits: HONDA FORZA, SUZUKI GSX1400, SUZUKI GSX1300R, SUZUKI GSX-S750, SUZUKI GSR750, HONDA PCX150, HONDA PCX150, HONDA PCX125, HONDA PCX125, HONDA NM-4, HONDA NC750S, HONDA NC700X, HONDA NC700S, HONDA CBR650F, HONDA CBR1000RR, HONDA CB650F, HONDA CB400SF, HONDA CB400SB, HONDA CB250R, HONDA HORNET900
Needed for CBR650R
The CBR650R has quite a lot of vibration, so the Weight will reduce it considerably and make it easier to ride!
The OEM bar end is equipped with a screw lock material, which is only a little difficult to remove, but the installation itself is very easy.
There are many different colors to choose from.
View detail
Fits: HONDA FORZA, HONDA PCX125, HONDA PCX125-E:HEV, HONDA PCX125Hybrid, HONDA PCX150, HONDA PCX160, HONDA ADV150, HONDA ADV160
Handling becomes lighter.
Running test
Weight of Bar End End 200g→170g." The Handle Ring becomes lighter due to the change of the handlebar's thickness, and the vibration transmitted to the handlebar is not a problem, but it may lack stability for those who often drive at high speeds. However, if you drive a lot at high speed, it may lack stability.
View detail
Fits: KAWASAKI GPZ1100, KAWASAKI GPZ900R, KAWASAKI NINJA250R, KAWASAKI NINJA400R, KAWASAKI NINJA650, KAWASAKI NINJA650R, KAWASAKI Z750, KAWASAKI Z750S, KAWASAKI Z800, KAWASAKI ZEPHYR1100, KAWASAKI ZRX1100, KAWASAKI ZRX1200DAEG, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZX-7R, KAWASAKI ZX-9R, KAWASAKI ZX14R, KAWASAKI ZZR1100, KAWASAKI ZZR1200, KAWASAKI ZZR1400
Just fit!
Since Bar End has been purchasing this Manufacturer for a long time,
We have long been aware of the quality of the product. This time, the vibration of the two-cylinder Engine
I purchased this product to take out. I am satisfied with the firm installation.
View detail
Fits: HONDA FORZA, HONDA PCX125, HONDA PCX125-E:HEV, HONDA PCX125Hybrid, HONDA PCX150, HONDA PCX160, HONDA ADV150, HONDA ADV160
The Shock driver in the instruction manual is not required.
About the product
The texture is very good, but it is smaller than expected. Grip and Bar End Cap A gap opens between the (Total weight:170g/OEM equivalent)
Installation
It's in the instruction manual. Shock driver." is not required.
Utilizing BOXWrench to meet Cap bolt (M6×40) standards. +Bit." and expressed in 10 levels of force, it can be loosened with about 30% of the force.Cap bolt has a Screw lock." A small amount of the "P" is applied and can be installed in about 5 minutes.
About the running test
We will re-submit if we feel a change is warranted.
View detail
Fits: DUCATI XDiavel, DUCATI SUPER BIKE 1299 Panigale, DUCATI DIAVEL, DUCATI StreetFighterV4, DUCATI SUPER BIKE PanigaleV2, DUCATI SUPER BIKE PanigaleV4R, DUCATI SUPER BIKE PanigaleV4, TRIUMPH Supersports Daytona 675, DUCATI SPORT TOURING ST2, DUCATI SPORT TOURING ST3, DUCATI SPORT TOURING ST4, DUCATI SUPER SPORT 900 SS, DUCATI SUPER SPORT 800, DUCATI SUPER SPORT 1000, DUCATI SCRAMBLER Sixty 2, DUCATI SCRAMBLER 800, DUCATI MULTISTRADA 1200, DUCATI SUPER BIKE 748, DUCATI SUPER BIKE 916, DUCATI SUPER BIKE 996
Unify Slider with AELLA
[How is it used?
Used for city driving and touring.
Was the one you received as per Image?
AELLA's Frame Slider, Front Axle Slider, and Rear Axle Slider had been installed in the past, and the design and texture are exactly the same, giving a sense of unity and high quality. (The design and texture are exactly the same, giving a sense of unity and luxury.)
Was the installation difficult?
Installation of this product is very easy as it can be done with a single hexagonal Spanner.
However, in my case, when removing the OEM Bar End, the tool was incompatible or rattled and licked the Screw hole.
If you are doing this as a DIY project, it is better to make sure that the OEM bar end can be removed without any problem. (The tool I used was Astro's Torx bit, and I managed to remove the OEMBar End because it was not tightened that hard.)
How was your experience with it?
The weight difference between the OEM Bar End and the OEM Bar End is not much, and I honestly thought the anti-vibration effect would be Brushbo. (I didn't feel that numb in the OEM condition to begin with.)
I feel that it is effective in terms of the appearance of the Slider system, which has become more unified.
[Included Parts:were they on?
Included Parts:Not available.
[Was there anything that disappointed you?
When an AELLA Bar End is attached to an OEMHandlebar or OEMGrip, there is a slight gap between the Grip and Bar End, and the Handlebar is visible. (This is the same with the OEMBar End, but the Bar End is now black, which makes the Silver Handlebar more visible.)
I thought that the Titaniumium washer that AELLA is selling is to hide this.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: HONDA CB1000R, HONDA CB1100, HONDA CBR1000RR, HONDA CBR1000RR, HONDA CBR600RR, HONDA CBR600RR, HONDA CB1300 SF, HONDA CB1300SUPER BOLDOR, HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
Cb400 handle bar ends
Excellent quality but it needs the proper fittings in the handlebar for it to attach. Make sure you have the right fittings for the handlebars View detail
To match Grip.
I changed the blue end to this one to match the grip to black. The brake lever is gold, so the grip is black and the end is also black. View detail
Fits: SUZUKI GSR250, SUZUKI GSR400, SUZUKI GSX1400, SUZUKI GLADIUS650400, SUZUKI GSX-S1000F, SUZUKI SV650, SUZUKI V-STROAM250, SUZUKI V-STROAM650XT, SUZUKI V-STROAM650, SUZUKI V-STROAM1050DE, SUZUKI V-STROAM1050XT, SUZUKI V-STROAM1050, SUZUKI GSX-S1000GT, SUZUKI GSX250R, SUZUKI BURGMAN400, SUZUKI V-STROAM, SUZUKI GSX-S1000S, SUZUKI GSX-S1000
Buy ja59
I wanted to install a low thickness bar end on my ja59, so after removing the OEM bar end, I tried to install it, but it was not possible.
I think I can install it by cutting and shortening the bar end fixing part, but I think I will save it for another motorcycle this time.
I learned a lot, I couldn't install it, but the design is good and I am satisfied with the product!
View detail
Fits neatly
Gold, the symbol of Manufacturer, is very Beauty! View detail
Fits: HONDA NSR250R
Bar End
Bar End, Design is good, so it is replaced.
It is not bad looking.
Quantity:Pair (for Left and Right) Quantity:2pc. The price is a little expensive because it is sold as a single pc.
View detail
Fits: YAMAHA MT-03, YAMAHA MT-25, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3, YAMAHA MT-03, YAMAHA MT-25, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R3
Nice construction and good design.
Design is good, good make,
It is good for dress-up.
You can enjoy color combinations.
Installation can be a bit tricky...
The drawback is that if it falls over, it is difficult to remove.
If you are going to ride on a mountain pass or Circuit and there is a possibility of falling, you can use a cheap Bar End.
It is a good idea to replace them when they fall over.
View detail
Bar End
The price is high, but the product is definitely made in Japan. View detail
Fit perfect!
I replaced the handlebar of my 2018 Suzuki SV650 with an aftermarket brand. New handlebar was made of aluminum alloy and the internal diameter was smaller at 14mm so the the OEM bar end did not fit. This product are heavy and fit perfectly. Waiting for the weekend to test the vibration damping effect on the handlebar. View detail
I don't know.
I don't know because I haven't tested the difference by replacing it with another Weight.
To the Handlebar, the coming seismic intensity has been reduced by a Large amount.
View detail