Reviews
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
For Repair
Purchased because I broke the Rear blinker by so-called cold cocking it.
CB400 NC39 SPEC1? OEM discontinued.
I thought about using a reproduct, but the bulb rating was low and I thought it would be a high flasher. If so, I decided to use LEDs.
Smaller than OEM, so Posh's 40mm extension was used for installation.
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
LED Blinker
It is a little expensive, but I am satisfied with the shape and stylishness. View detail
Genuine Yamaha Fuel Tank Pad for MT09
This was something I had been meaning to buy but never got around to it. The correct tank pad was not hard to find, I just filtered the manufacturer and then model of bike and there were a couple to choose from. I deceided on the genuine Yamaha one as it will fit as it should do with it being made for this bike. The cost was not too bad actually and better than I had seen for sale locally. With a couple of other tank pads for other bikes, I had them all shipped together via EMS. EMS just do what they say and get your order to you quickly. Mine arrived 5 days after the shipping date which is perfect. The entire order was neatly packed in the box, the tank pads were all kept nice and flat so there was no distortion which could have been a problem when fitting. The tank pad came in a Yamaha packet and was neatly presented. The pad itself feels very nice and smooth but does have a bit of friction due to the materials used. I was expecting a slightly more domed gel pad but for what it is, it's fine for my needs. Fitting was straight forward and when on without issue although I pre fit with low tach tape to get the placement visually before starting. Pleased with the purchase and hopefully, this stops any future scuffs from happening with my jacket zip. Thanks Webike View detail
Weak rigidity of the bar
I installed it on my 2nd model MT09SP, but it is a large size because it interferes with the controller of the rear suspension. The bar is not rigid, so when the back is attached, it bends inward, so I have to check the interference with the tire every time I attach it. View detail
Genuine Yamaha Tank Pads for MT07
These were purchased to help protect the side of the fuel tank from scuffs. There was already a centre tank pad fitted but the side was open to accidents. The correct part was not hard to find. I just used the search facility on Webike and narrowed down the search to OEM Yamaha and fuel tank protection. There was a few to choose from but only this one was specifically Yamaha branded. The cost was pretty good for such a good tank protector and along with a few other items in my basket, I got them all shipped together to save on a bit of shipping cost. I generally use EMS these days as they just get the job done. I almost always get my order delivered within a week and more so in 5 days from shipping Webike warehouse. This was no exception, the order arrived in 5 days as expected. The outer box was sealed along each side and the inner was well padded out. Witth these tank pads being flat and needing to stay that way during transit, Webike ahd the taped to a large piece of cardboard to keep them safe. This worked a treat. The tank pads themselves were packaged in a nice Yamaha standard packet. They are flexible but do have some structure to them. They were slightly on the thin side but when you think about it, if they were much thicker, you would struggle to gethem placed where you need them anyway. I am very pleased with the purchase and look forward to trying them out on the road as they also supoosed to give a little grip to the tank too. Added bonus. Thanks Webike View detail
I like the tuning fork Mark.
I bought it because I like the design. I expect it to be durable.
The curved tank at the bottom was attached by pushing it down. I think it is better to stick it carefully here.
I'm a tedious person, so I do it in one shot, but the original procedure is (1) Centers. (2) Spray an appropriate amount of diluted neutral detergent (3) The order is to paste and adjust the position.
View detail
Nicely fit
Nicely fit, on my yamaha 2014 mt09. No modification needed. Fast shipping from dealer. Item solid and original, will continue support the website View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
YamahaOEMBlinker
The look is Carbon Style and cool, and the brightness is bright and perfect. View detail
Fits: YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA XSR700, YAMAHA MT-09 SP, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
I am repeating this LED Blinker on my Yamaha car.
[How is it used?
I installed this product on my 2014 YZF-R1 Rearfor Blinker as a LED winker conversion. (I'm considering to convert Front to Built-in)
Was the one you received as per Image?
As a YamahaOEMLED Blinker, it was small in size and true to its image.
Was the installation difficult?
Since I have an external Fender Eliminator on the rear, I used the included RubberSpacer to add bulk, but the body just barely sticks out.
How was your experience with it?
If you install it as it is, one-third of the body is hidden by the width of the License Plate, so I raised it with the included SpacerRubber. It may be possible to consider further raising the height with a few more centimeters of Spacer.
[Included Parts:were they on?
OEMRelay-compatible resistors and Brackets were also included.
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
Opinions and requests to Manufacturer
I would like to sell from Body1pc. as a part, as a supplemental part.
View detail
Ease of attaching Yoke Protector
I was worried that the installation position would shift and I would have to reattach it, but the product is one size smaller and fit naturally between the convexes of the yoke and could be attached in one step. View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
Installed on SEA BASS Motorcycle.
[How is it used?
The design of the OEM blinker of the GSX-S1000F was not to my liking, and while searching for a blinker with a better design on Webike, I found an LED blinker with the design I liked in Yamaha's Option product. I found an LEDBlinker of my favorite design in Yamaha's Option product, so I bought it.
I am now going around and using it on my SV650X.
Was the one you received as per Image?
Today, LED blinkers of various designs are available from various companies, but at that time, LED blinkers were just starting to be released by ThirdParty, Parenthesis is good!" The price of Blinker, which seems to be a good idea, was still too high to be easily replaced.
In such a situation, this product is for one unit (4 Blinkers). If you work hard, you can reach it." When I learned from Webike that it was available in my price range, I did not hesitate to purchase it, and it is just as Image described.
Was the installation difficult?
This time it was included in the package. Resistance is not used, but rather an LED-compatible ICRelay made by DRC.
Essentially, one resistor is attached to one BlinkerWiring and connected to the Wiring on the car body side.
Cowl removal and installation rather than installation of this product. "Getting there and after installation." work was tedious.
Once the exterior has been removed, the only thing left to do is to remove the OMBlinker and replace it with the product, and then use a different manufacturer's product. Cowl mounting collars will be almost complete.
The Wiring connections are "Bullet Type Terminal So, if you replace it with the OEM TypeCoupler for each manufacturer sold at KITACOConvenienceParts or Poshetc., you can have the same beautiful Wiring process as OEM.
How was your experience with it?
As expected of a Yamaha OEM option product, we are very satisfied with the CoolDesign, which is neither conspicuous nor causes deterioration of visibility.
[Included Parts:were they on?
Quantity of 2 BlinkerBodies and 2 resistors to be attached to each:Set, 2Quantity of this product for 1Large vehicle.:You need to purchase Set.
[Was there anything that disappointed you?
No complaints, high quality, and if you like the design, you will love it.
Other items that would be helpful
Point and hang of installation
By Vehicle or Manufacturer Blinker mounting collars. can be purchased separately for uncomfortable installation similar to that of the OEMBlinker.
[Availability and clarity of the Instruction Manual
There is an Instruction Manual, and although the level of difficulty is a little higher for those who are not good at electrical work, it is manageable if you read the Instruction Manual carefully.
[Notes]
If the OEM has a vehicle with LED Blinker, the included resistors and LED-compatible ICRelay are not required.
[ITEMS TO BUY TOGETHER
For vehicles that have a Large threaded hole when removing the OEMBlinker, it is recommended that the vehicle be fitted with the appropriate Blinker mounting collars. if you want to do a Beauty Wiring process like the OEM state. OEM TypeCoupler by Manufacturer If you don't want to install resistors on each Blinker, you can use the LED-enabled ICRelay separately.
[Opinions and requests to Manufacturer
I like the design, so it would be great if you could change the model to a more modern style of LEDs where you can't see the grains of LED bulbs while keeping the same exterior shape.
View detail
Yamaha Rear Carrier for MT09 / MT10
Bought for my MT09 2015. Product easy to install as it like plug and play except need to make hold at the bike side cover yet it still so easy as the marking already being mark at the cover. Look great and sturdy. Waiting for the Yamaha Top Box to arrive. Overall service from Webike are great and really fast delivery for EMS. Order from 2 March 2023 and received the item at 5 March 2023 from Japan to Malaysia. View detail
Used with Carrier only & no Box
The installation was done by Shop.
Not only the 09, but also other recent motorcycles have small rear sets, making it quite difficult to load them as they are.
Also, I really don't like the idea of attaching a Box to anything other than Scooter, so I used a WaterproofRucksack bundled with a Net on this Carrier. (I use the Box in the Scooter because it is convenient. (I use the Box in the Scooter, because it's convenient.)
By doing so, I was able to use it in such a way that the overall silhouette would not collapse, luggage could be attached, the luggage would not get wet, and valuables could be carried around with it. It is nice to be able to carry a person in the back with luggage strapped to it.
The body color of the 09 is dark purple and the Carrier is black, but you can't tell the difference if you don't look at the gun up close.
View detail
OEMQuality
Since I bought my MT-09 used, it came with this.
I replaced the Tank, so now I bought a new one and stuck it on.
I think Parenthesis is good because it matches the design of MT-09.
It seems to be durable, but the surface of the first one that was attached to it had a WHITE look to it. Is that due to the material? I guess it can't be helped.
Since the base paper also serves as a pattern for pasting, I think it can be pasted on Beauty.
View detail
Factory Luggage Rack MT-09/MT-10
This is a factory luggage rack for the MT-09 and MT-10. It fit my 2022 Yamaha MT-10 perfectly. This part number is the same as the United States part number of 1RC-F48D0-V0-00. The only difference is it is offered here in silver or black. This came with instructions for both MT-09 and MT-10. In my picture you will see my commuter bag and straps. No problem fitting either one on the bike. The rack is solid once mounted on the bike. It does not move. I also used blue thread locker on it to make sure. Very happy with the part! I also like the very clean look of the rack. It bolts to the seat frame in spots that are already there from the factory. The only holes needed were through plastic. I used a step drill bit to make those holes. Then just screw in the four bolts with washers and done! Very Easy! View detail
Mounted on Mt09sp2022
If the Seat is not removed and worn, the Logo on the Tank is hidden. Also, some air was getting into the tank. View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
MT-09 YamahaEuropeLED Flasher
I was looking for an LED Blinker that is not too small, as the MT-09 (2017MODEL) Blinker is not a standard LED. I also didn't like the OEM mounting position, so I tried to change the position as well.
The Front was changed to the position next to the Meter, and the Rear was changed to the License Plate, giving it a cleaner appearance.
The YamahaEuropeBlinker is not plugged into the OEMCoupler (gibo), so it takes a bit of work, but it is not too much trouble.
Design, I have no complaints about the light level.
View detail
Even though it's an OEM Product…
Rough paint job even though it is YamahaOEM Product.
I was disappointed with the same Level as the $5,000 Chinese product.
View detail
Fits: YAMAHA XSR700, YAMAHA XSR900, YAMAHA MT-09, YAMAHA MT-09, YAMAHA MT-09 SP, YAMAHA MT-09 SP, YAMAHA Applicable to 12V 10W only, YAMAHA MT-09, YAMAHA YZF-R15, YAMAHA YZF-R125, YAMAHA XSR125
Installed on a Racer 900GT
I installed it on a 2020 Toracer 900GT.
I purchased the LEDs because other manufacturers have been using LEDs for quite some time now, but Yamaha is still using bulbs at this time.
The installation is a little troublesome. The front panel is double-layered where the blinker is attached, so the inner panel is screwedQuantity:Quantity 2pc and special clasps:2pc. The Rear side is easier to work with if you remove the license plate bracket. And Quantity:Pair (for Left and Right) I put the resistor inside the Seat Cowl on the Rear side, but I think it is better to avoid the plastic part because of the heat generated. I did not want to cut the OEM wiring, so I bought a Conversion Connector and installed it, so there was no wiring. I am happy with the way the light shines differently than the OEM.
View detail
Looks are everything?
It's all about looks, right? It doesn't work, it doesn't do anything. I bought it in Black because they were out of Silver and painted it. Silver was out of stock, so I bought a Black one and painted it? I am not satisfied with it, right? View detail