【ZETA】SX3 Handlebar MX-313 Review

Stable operation

Installed on CRF250l. Taper Handlebar is a little bit difficult to replace the attachment around the handlebar due to its size diameter. It was a little bit difficult to replace the attachment around the handlebar, but I think it made the operation better. I am glad to have replaced the standard handlebar with this one. View detail

Just the right height

The OEMHandlebar of YZ125X was higher, so we bought this one, which is about 1cm lower.
This time I am replacing Handlebar because I gave it to an acquaintance.
It is also significant that I bought it because the Baba brothers recommended it.


[How is it used?
Enduro race (Grass Race) I bought it to put on my YZ125X that is going to
I don't do any hard races, but mostly GRUGRU-type Enduro races, occasional forest roads, and practicing on the course.
I had a pretty large fall, but the handlebar did not bend. (OEMLever broke).


Was the one you received as per Image?
The Handlebar width was too wide as per the figures in the fit table, for better or worse, as per Image.
Strength was stronger than Image.


How was your experience with it?
ZETA Material:All of the Aluminum products are weak Image, but Handlebar was very hard to bend.
The height is also Exactly and definitely easier to ride than OEM.
I don't feel any demerit such as not being able to reach the handlebar when descending etc. if it is about 1cm.


[Points to note]
The Aluminum Ground is soft and will scratch the mess when the Hand guard Clamp is installed.
And the standard height of Japanese people. (172cm) As for me, the Handlebar is too long, so I cut One Side 2cm each.
I wish there was a shorter Handlebar width product.
The attached Bar pad is easy to come off, though not as easy as YamahaOEM, so it is recommended to use 25MODEL's OEMBAR pad. (OEM Product No.:BHR-26124-00) to the \"M\" in the \"M\" column.
Also, when installing the odi lock on grip, the Knurl portion of the Clutch Side is too thick to fit at all, so a lot of shaving work is required.


How did it compare to other products?
I tried a handlebar called \"universal low\" by Pro taper, which is a little lower, but it was either pulled too much or hung too much, or it did not come firmly when cornering, so I quit.
I really wanted a Renthal Handlebar, but I couldn't find one with the right height, so by process of elimination I ended up with this product.


I don't know about 4st YZs, but I think this MX-111 would be easier to ride than the OEM if you are around 160-170 tall in a 2st YZ. View detail

Almost the same shape as Husk's TE300 OEMHandlebar

Purchased for use with HUSQVARNATE 300 used with HardEnduro.
Although we wanted to lower the Handlebar, it was almost the same shape as the OEMHandlebar (pro taper).
It will be kept as a spare for a while.
ZETA handlebar has a knurl on the left side, so it needs to be modified to eliminate the unevenness in order to install the lock on grip. View detail

Pricey, but a good buy!

Replaced the Fat bar with this Fat bar!
For VSTROM250SX Type:FMX-TAKA I assembled a Higashino ReplicaMODEL that says!

It was a very interesting experiment with a very rare Bar End shape. (^。^) y-. O-
The last Handlebar was not tall enough to begin with, so it ended up being a good choice!

It is a sharp handlebar^^; with a narrow width and a raised end, but it is easy to change the Machine to a Large size.
Controlable Handlebar now! 。 As a result, it was the right decision to buy it! View detail

Increase in body range of motion

I was looking for a low handlebar width and this product caught my eye.
Comparing the one I actually received with the one I have now, it was clear that the low handlebar was exactly what I was looking for.
Handlebar width is still long, so Quantity:Pair (for Left and Right) 1.I cut off about 5 cm to just fit my width and adjusted the handlebar angle to my liking by lowering it toward me.
When I actually used it, the Handlebar was low and brought a little forward, so I felt I could move more than I wanted to with a wider range of body motion.
This was my first time using Zita's Handlebar and I think it is a great product. View detail