【ODI】MX V2 Lock-on Grip Review
Fits: HONDA CR125R, HONDA CR250R, KAWASAKI KX125, KAWASAKI KX250, SUZUKI RM125, SUZUKI RM250, HUSQVARNA TE300, SUZUKI DRZ400SM, KTM 50SX, SUZUKI DRZ400S, SUZUKI RMZ450, HONDA CRF450R, HONDA CRF250RX, YAMAHA WR250F, YAMAHA WR450F, YAMAHA WR450F, YAMAHA WR250R, YAMAHA WR250X, YAMAHA SEROW225WE, YAMAHA SEROW250,
In reserve.
Purchased as a spare because it was worn out and had to be replaced. The gnawing feeling is great, but a little durable.
Responses
Other reviews
Easy to install and remove! But it doesn't turn!
[How is it used?
The handlebar was replaced at the same time as the handlebar replacement.
I could have used a regular Grip, but SEROW250 was on the compatibility list even though it is not a Racer, so I really wanted to use it when I switched to SEROW250.
It's been about 200 km since the replacement, which is an alternative.
Was the one you received as per Image?
It's just as I imagined. No more, no less, but the Grip end is cool.
Was the installation difficult?
On the Throttle side, simply select a cam from the compatibility chart and snap it in place, but be sure to carefully align the cam position.
If you put it in without thinking, the waffle will be in an unexpected position (yay!).
The Clutch Side is simply placed in the Handlebar and tightened with a screw, but the Clearance is tight.
This time, Renthal did not need to be shaved as described in the product description, but I could feel the palm of my hand tapping into it.
The screw is thin, so be careful about overtorque. 1.69Nm is a range that cannot be measured with a torque wrench, so use a hand torque wrench to the extent that the screw does not spin out of control.
How was your experience with it?
Once it's on, it's just like a regular Grip. The slightly soft compound does not make it sticky, but it has a good bite. 。 There is a feeling that if you are a spirited runner, it will decrease quickly.
Unlike OEM, there is a gap between the Throttle holder and the Throttle holder, but so far it has not affected practical use. I expect that the "Mimi" part moves softly, so it is like a grip doughnut. I am hoping that the soft and movable part of the "Mimi" will be like a Grip doughnut and prevent blisters from forming.
By the way, I expected it might be a little High Solo since it is the same Cam as Racer, but when I compared it, it was the same thickness as SEROW250OEM.
[Included Parts:were they on?
It comes with some Cam for Replacement. Please check DirtFreak or the original site for the compatibility list.
[Was there anything that disappointed you?
I was wondering if it is necessary to have a fine footpeg for mounting the cam on other Lock on-like grips. I was wondering if it is necessary to have a fine footpeg to mount the cam on other Lock on-like grips.
With the standard Throttle holder position, it shifts a bit, so you can either cut the boss and shift it to accommodate or compromise. If you are concerned about it, you may be bothered by it. Currently, we compromise on the positional relationship between the kill switch and the throttle holder, and we have set the quantity:Pair (for Left and Right) The Waffle position is a little off in
Cautions for installation.
There is no instruction manual, so you need to refer to Site 。 Well, it is not that difficult.
The Hexagonal Wrench to tighten the screws on the Clutch Side is not included.
As with all grip changes, after removing the thruggle holder, clean the wire thailand and the inside of the thruggle pipe, and reapply grease. If you neglect to do so, the throttle will become heavy and dull (I have done this in the past).
View detail