【Vesrah】Resin Brake Pad Review
Fits: HONDA VF700C Magna, HONDA VF1100S V65 Sabre, HONDA VF1100C V65 Magna, HONDA VF1000F, HONDA GL1200SE-I Gold Wing Aspencade, HONDA Shadow 1100, HONDA GL1200L Gold Wing LTD, HONDA GL1200I Gold Wing Interstate, HONDA GL1200A Gold Wing Aspencade, HONDA GL1200 Gold Wing, HONDA GB500, HONDA CBX750F, HONDA CBR750F Super Aero, HONDA CBR1000F, HONDA CBR600F, HONDA VFR750F, HONDA VFR750F, HONDA VFR700F2, HONDA VFR700F, HONDA VF750F,
The result of using various Manufactures
I've used a variety of manufacturers' products, but I've never had a middle class old car. (70s to early 80s) It was the best overall experience for
Especially the slowed down Fee Ring and the less aggressive nature of the disc!
If you don't have external parts, you can't use Metal pad easily because you can't replace the disc as soon as it is damaged.
Of course, it's a Resin pad, so it's not as good as Metal pad.
However, the overall price has gone up so much that it is not a candidate for the next replacement.
I'll use the Red Pad again for the Dust...
It may not be suitable for heavy Large type old car or powerful body (Durability wise)
Responses
Other reviews
Necessary and sufficient efficacy
I am using it with KawasakiZ1.
We are on Double disk with OEMCaliper.
Is it thanks to the Shim on the back of the Pad?
No squeaking so far.
Braking force, but it does not perform Race.
It works well enough for the TouringLevel's muddy driving.
If you say that this Pad does not stop, then that is too much Speed.
View detail
Maintenance
I replaced the Front Brake Pads on my Z1R with Vesra's. The pads no longer squeal and I can break without worry. I don't know about the durability yet. View detail
SD-401 should be called the old one.
Using it as it is, it is like that to begin with, but even the double disk on the 650RS W3 only works vaguely.
Especially with Solid's Rotor without Slit, it is the worst in the rain, it doesn't work as well as it should.
This is an area where I would like to ask manufacturers if they can do something about the friction material.
We are working very hard to stop squeaking and increase braking power, but the methodology is a secret.
To increase braking force with the old Tokico Caliper, the Caliper design philosophy must be revised.
Also, the Package was changed from the one I purchased this time, and the Pad has a groove, but the inside of the Pad is not the same as the one I purchased this time. (Fixed side) the groove is in the radial direction of Rotor, but the outer (Piston side) But unbelievably, the grooves are circumferential.
I would like to ask Vesla what he is thinking on this point.
View detail
GOLD WING1500SE R replacement
I decided to go with Resin because of the Record board pattern on the Metal pad, it is thicker and the braking force is ?approximately right.
To make the most of the braking power, we polished the Brake Disc to remove the record pattern. After a light test ride, it was perfect!
Disc Rotor is also ? expensive, so disc friendly is the best.
For the time being, the Rear area is Large sturdy.
View detail
malformation
I had bought Besra because it didn't squeak Brake.
The exchange would normally have taken 30 minutes to complete.
The Pad I purchased this time holds the Brake lever.
Glitch that does not return at all.
Initially, I inspected the vehicle body side Braque hydraulic failure and installation defects many times.
Not at all. I asked my go-to Shop and no luck.
It took me 3 hours to give up and put a pad with 200km on it.
Successfully installed and BreakingOK.
The Piston grounding surface of the Pad on the B side of this purchase was in poor shape.
It was a problem with the Pad not returning.
Get a store that specializes in OH.
"Drove 200km, Pad attached to front." is made by Besra.
What's this?
I did the maintenance myself and the Brake squeal went away.
I'm assuming you just happened to hit a defective product in a production lot.
Vesla's credibility has suffered.
Caliper is hurt and angry.
View detail