【DAYTONA】Hyper Pad Brake Pads Review
Fits: SUZUKI Sky Wave 400, SUZUKI Jebel 250, SUZUKI TS200R, SUZUKI TS125R, SUZUKI RMX250, SUZUKI RMX250 S, SUZUKI DR250SHE, KAWASAKI KX250, KAWASAKI KLX250, SUZUKI DR250S, KAWASAKI KX125, SUZUKI RM125, SUZUKI RM250, KAWASAKI KLX230R, KAWASAKI KLX125, KAWASAKI KLX230, KAWASAKI KDX250SR, KAWASAKI KDX200SR, KAWASAKI D-Tracker, KAWASAKI D-Tracker X,
Used on the front of the TS125R
[How is it used?
Used with TS125RFront.
Application:Off-road
Replaced OEMPad.
Was the one you received as per Image?
Just like the image. They were Brake Pads with an unadorned feel.
Was the installation difficult?
The installation is not that difficult, and if you have enough time, it is very durable.
However, if the piston is sticking or is reluctant to move, it will take a bit of work.
When removing the pad pin or caliper mounting bolt, it is recommended that you use a good precision tool from a proper tool manufacturer if possible.
When you remove the Pad, you can push the entire Pad when you push the Piston back. (Skinning) This can be done easily by using
How was your experience with it?
Compared to the OEM, I think it had the same effect and controllability. At the time, I had no problems with the Skill and was able to decelerate at the speeds I was capable of. However, when I first changed the brake pads, I regretted that I should have chosen the Red Pad from DAYTONA, because with the Red Pad, I could decelerate at a faster speed range without worry, and I missed the chance to improve my kill.
There was not much aggression to the Disc Rotor, and the Pad itself lasted a long time.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
As my own kill increased, there were times when I wanted it to work.
(Points and hangs for installation/things you should prepare together)
As the installation point or hang, the
To reduce the squeal, chamfer the short side of the pad with an ironworking file.
Apply a thin layer of brake pad grease to the surfaces of the caliper and piston. (Base material) If you apply it on the whole side, Dust will not adhere well.
If the surface of the pad pin is covered with rust or dirt, I use about #400 water-resistance paper and inexpensive lubricant such as Kure 556, etc., and clean it with oil. Then apply a thin layer of pad grease and install.
Use a mild detergent and tooth brush to clean the caliper. Use a mild detergent and toothbrush to clean calipers. ・Parts cleaners that are less aggressive to rubbers should be used only where there is a lot of dirt. (Chain cleaner) Cleaned at
Spray the entire caliper with silicon spray and wipe it with a dustcloth. (Before installing the pad)
You may want to prepare the following items together
Pad grease
Lubricant for oil sharpening
Silicon spray
RubberGrease or Silicon grease (For piston cleaning and wringing out)
Parts cleaner (Chain cleaner)
Scraper (A leather skewer or slotted screwdriver is also acceptable.)
Iron Rasp
Water-resistance Paper
PistonPliers (PistonTool) (For piston cleaning and wringing out)
Pad pin (If the rust is severe and causing bumps)
Responses
Other reviews
Used in Caliper for RZ50
We chose the cheapest one because it is used for city driving and touring.
The durability is not bad, and I would buy it again.
View detail
It can be used normally
Pad was getting low, so I replaced it.
It's not particularly faulty or ineffective.
View detail
Not installed yet.
I ordered this for my NSR50 RearBrake CaliperOverhaul. View detail
DAYTONA Front Brake Pads VIRAGO250
I am satisfied with the quality, cost performance, and controllability. View detail
Pad replacement
Pad replacement for LEAD125.
I ran it for a bit and it looks fine.
View detail