PAGE TOP

【K-CON】Aluminum Spacer Collar for M8

    • Evaluation:

      It is perfect!!

      • Contributors: Japan User(translated)
      • Published on: 2019-03-01 10:17:55
      It is perfect!!

      Responses

      In response to comments please "Login" and complete "Full Registration"

      Other reviews

      Quantity as a Spacer for Bracket on Handlebar Post : 2pc. It is a purchase of eyes eye. In order to secure the distance to Meter when installing LED Monitor on the new Handlebar Post this time, this KITACOConvenience Parts K-CON : I purchased Exclusive Aluminum Spacer for M8 Screw. KITACOConveniencePartsK-CON is rich in variety and handy

      I used it for position adjustment of oversea made Exhaust System. KICK interference, footpeg interference etc.. Yes, Large Ideal for adjustment in units of a few millimeters. These parts are saved for Large change.

      I purchased it as a Spacer for Bracket on Handlebar Post. Before buying Spacer, I had dealt with several Washer piles, but I found this Spacer, purchased and exchanged and refreshed. KITACOConveniencePartsK-CON is rich in variety and handy.

      【What made you decide the purchase?】
      When SUPER SHERPA turns on Hand guard, Banjo bolt of Front brake interferes with the Guard iron core.
      If you adjust the angle of Hand guard, Brake hose, you can prevent it from interfering, but at that angle the wrist bends excessively when running at standing and it is hard to drive so purchase to buy it.

      【How was it actually used?】
      It is an ordinary M8 Spacer with an outer diameter of 13 mm and a thickness of 30 mm.
      There is not much Spacer of this Size, KITACO is such a fine Lineup is wonderful.

      【Mounting was difficult?】
      Just remove the Hand guard and insert the Spacer and install.
      At that time Bolt needs to be replaced as well.
      I am Trusco Zhongshan B23-0860 [Hexagon BoltStainless Steel Half Screw Size M 8 X 60] I used Bolt.
      Incidentally, this Bolt can also be used to attach OEMStack Bar of SEROW 225 to KL 250 Sherpa.

      【Please tell me the installation point and hang】
      You need to bend the hand guard a bit to make 30 mm of space.
      I inserted it in the near side gutter and bent with this principle. It turns easily unexpectedly.

      [Is there anything I was disappointed about?]
      There is none.

      【Hope for Manufacturer - Please let me know if you have any improvement points]
      There is none.

      【Have you compared items?】
      No. quotient ProductNo : ZE 71-1713, ZETA Zeta : Replacement Mounting Kit Extended Size
      Manufacturer's genuine goods are also available, but as KL 250 Sherpa interfere in KL 250 Sherpa it is only Brake side to buy both Mount Kit because there was resistance, so I bought it off.

      [Others]
      Was it OK even if the outside diameter was 18 mm?
      It seems to break from here when it is covered.

      I think that price is also cheap and it is very convenient to choose thickness and inner diameter. With these items, Universal Product is also easy to use. Chamfer itself is solid, too, it feels carefully made.

      【WebikeMonitor】
      There is a Rubber in the Cowl part to install RearCarrier, but as you tighten Bolt, the Rubber will collapse and Cowl will be damaged, so you can protect Cowl by putting a Spacer.

      It was used for attachment of the Screen considered to be an external article MT-01. Since there is a kind with a splendid diameter of

      inside and outside, a just right Size should be found generally. Probably,
      finishing will be reasonably priced. It is the highest if there is
      Color-alumite specification.

      The Lineup also of such accessories is carried out and they are very convenient.I thought that he was Brando who can also trust quality without a problem.

      if it exchanges for the Separate handle made from madmax -- the Spacer of the Convenience hooks of the
      KITACO --
      -- since it was short and had been buried, it lengthened 5 mm.
      --
      to which a Convenience hooks did not need to become useless now, either -- it is convenient if you use such goods well.

      A box was not attached without this product.
      Between a base and a clamp, kiln is carried out and desorption of a box is enabled.
      Although it is casual goods, there is a size aimed at perfectly.
      It is important in Colet.
      He is an unsung hero.

      It used in order to make the old type disk rotor of SR400 into flange bolt & wire lock specification.
      If there is this [ no ], the outer circumference of a flange will not be hit and fastened on the edge of a hub.
      Therefore, it is that of ! regarded as one-piece 200 yen over being high but although appreciated very much, and is three.

      it used for an external chamber and pure stay to carry out location appearance.
      It is the touch which may come to be pure in not attaching to a silencer band but making a stay main part offset.
      If it was a decade ago, had just been going to attach forcibly, but there are parts which also reach an itchy place and they are saved these days.

      Although he bought it for height adjustment, since the die length of an outside with a cap was together, it is comfortable and was decided.
      He buys it and I think that it was good.

      In hand guard wearing, it was used in order to avoid interference of a throttle holder and a grip.
      Since it is the thing which was being looked for, it is a five stars without a complaint!

      If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!!
      The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 25-mm product.
      If existence of Webike is not known Didn't it meet with the aluminum spacer collar made from a kitaco, and the vivid bolt?,
      .
      .
      By Webike, customization filled to originality and creativity can be performed, and it is a delightful limitation!! An attached image,
      The muffler made from p's supply is treated to the address V125, and it is a muffler protector made from burial. (tune by a moriwaki sticker and #OS800-30000-41!!) In order to equip,
      They are contents which use the aluminum spacer collar made from a kitaco and vivid bolt which are the products chosen as the end of deliberation.
      The spacer collar made from a product muffler protector made from burial 竊?kitaco.
      (#0900-093-00059, inside diameter phi8.2mm, outside-diameter phi20mm, and 25 mm in height) Product muffler made from product muffler made from product muffler made from 竊?p's supply attached silencer band 竊?p's supply attached M8 aluminum-collar (outside-diameter phi23 mm and, and 22 mm in height) 竊?p's supply attached aluminum -.
      Washer & flange nut we for product muffler made from billet plate 竊?p's supply attached silencer band conclusion,
      - vivid bolt made from a kitaco of M8x100 (#0900-080-0015) was chosen for the bolt used of this customization!! [ -- [refer to [ the in play part 1 ]] ], if two or more sets of the addresses V125 which drive the inside of a town are seen,
      It seems that its respectively different customization was given, and each was colored with personality and loves.
      Moreover, is conversion of a muffler mentioned the common feature of the customization?
      .
      .
      As a protector to the replace muffler which you chose, if it equips with the chamber protector made from burial, it is how?
      (Incidentally the outside diameter of a white duracon resin part is phi36mm.)
      The size of the sticker of a moriwaki is about 56 mm.
      Since the outer circumference of a duracon part is about 113 mm, the sticker of a moriwaki becomes a size like the semicircle. Replace muffler which incidentally must be praised, steiner muffler made from p's supply !!.
      (A thing with a pleasant low-and-medium-speed strengthening muffler to the extent that a willy is likely to be carried out by zero start TSU which is a word!!)

      If it says from [[in play part 2]] conclusion, the products here will be the highest products in general!!
      The aluminum spacer collar here is inside diameter:phi8.2mm. Outside diameter: phi20mm Height: It becomes a 30-mm product.
      If existence of Webike is not known Didn't it meet with the aluminum spacer collar made from a kitaco, and the vivid bolt?,
      .
      .
      By Webike, customization filled to originality and creativity can be performed, and it is a delightful limitation!! An attached image,
      The muffler made from p's supply is treated to the address V125, and it is a chamber protector made from burial. (tune by a moriwaki sticker and #OS800-30000-41!!) In order to equip,
      They are contents which use the aluminum spacer collar made from a kitaco and vivid bolt which are the products chosen as the end of deliberation.
      The spacer collar made from a product chamber protector made from burial 竊?kitaco.
      (#0900-093-00060, inside diameter phi8.2mm, outside-diameter phi20mm, and 30 mm in height) The engine side of the product muffler made from product muffler made from 竊?p's supply attached aluminum billet plate 竊?p's supply attached M8 aluminum-collar (outside-diameter phi20 mm and, and 14 mm in height) 竊?address V125.
      A muffler mount and M8 female-screw partial we the bolt used of this customization,
      - vivid bolt made from a kitaco of M8x100 (#0900-080-0015) was chosen!! [ -- [refer to [ the in play part 1 ]] ], if two or more sets of the addresses V125 which drive the inside of a town are seen,
      It seems that its respectively different customization was given and each loves the address V125 colored with personality.
      Moreover, is conversion of a muffler mentioned the common feature of customization of the address V125?
      .
      .
      If it equips with the chamber protector made from burial, how is it as a protector to the replace muffler which you chose (the outside diameter of a white duracon resin part is phi36mm.)?
      The size of the sticker of a moriwaki is about 56 mm.
      Since the outer circumference of a duracon part is about 113 mm, the sticker of a moriwaki is a size like the semicircle.
      it is just a sticker tune of a just size!! Replace muffler of the address V125 which we incidentally cannot but praise, steiner muffler made from p's supply it is -- TSU!!

      It was used for the height adjustment of the attachment of a hand guard.
      Since an outside diameter, an inside diameter and die length, and a variation occur and it can purchase and tune finely to number type 1 clue, it is convenient.